We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • BS ISO 4437-1:2014 (published 2014-01)

    Current The latest, up-to-date edition.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    Plastics piping systems for the supply of gaseous fuels. Polyethylene (PE) General

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  31-01-2014

    Publisher:  British Standards Institution

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Symbols
    5 Abbreviated terms
    6 Material
    Annex A (informative) - LPG and manufactured gas
    Bibliography

    Abstract - (Show below) - (Hide below)

    Describes the general properties of polyethylene (PE) compounds for the manufacture of pipes and fittings intended to be used for the supply of gaseous fuels.

    General Product Information - (Show below) - (Hide below)

    Committee PRI/88/2
    Development Note Together with BS ISO 4437-2, BS ISO 4437-3 and BS ISO 4437-5, it supersedes BS ISO 4437, BS ISO 8085-1, BS ISO 8085-2 and BS ISO 8085-3. Supersedes 12/30256736 DC. (01/2014)
    Document Type Standard
    Publisher British Standards Institution
    Status Current
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 4437-5:2014 Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) Part 5: Fitness for purpose of the system
    ISO 13953:2001 Polyethylene (PE) pipes and fittings Determination of the tensile strength and failure mode of test pieces from a butt-fused joint
    ISO 1167-2:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 2: Preparation of pipe test pieces
    ISO 1133-1:2011 Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 1: Standard method
    ISO 6964:1986 Polyolefin pipes and fittings Determination of carbon black content by calcination and pyrolysis Test method and basic specification
    ISO 9080:2012 Plastics piping and ducting systems Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation
    ISO 13477:2008 Thermoplastics pipes for the conveyance of fluids Determination of resistance to rapid crack propagation (RCP) Small-scale steady-state test (S4 test)
    ISO 3:1973 Preferred numbers Series of preferred numbers
    ISO 4437-2:2014 Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) Part 2: Pipes
    ISO 18553:2002 Method for the assessment of the degree of pigment or carbon black dispersion in polyolefin pipes, fittings and compounds
    ISO/TS 10839:2000 Polyethylene pipes and fittings for the supply of gaseous fuels Code of practice for design, handling and installation
    ISO 13479:2009 Polyolefin pipes for the conveyance of fluids Determination of resistance to crack propagation Test method for slow crack growth on notched pipes
    ISO 11414:2009 Plastics pipes and fittings Preparation of polyethylene (PE) pipe/pipe or pipe/fitting test piece assemblies by butt fusion
    ISO 12162:2009 Thermoplastics materials for pipes and fittings for pressure applications Classification, designation and design coefficient
    ISO 6259-1:2015 Thermoplastics pipes Determination of tensile properties Part 1: General test method
    ISO 13478:2007 Thermoplastics pipes for the conveyance of fluids Determination of resistance to rapid crack propagation (RCP) Full-scale test (FST)
    ISO 16871:2003 Plastics piping and ducting systems Plastics pipes and fittings Method for exposure to direct (natural) weathering
    ISO 472:2013 Plastics Vocabulary
    ISO 13954:1997 Plastics pipes and fittings Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm
    ISO 1183-1:2012 Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method
    ISO 1183-2:2004 Plastics Methods for determining the density of non-cellular plastics Part 2: Density gradient column method
    ISO 15512:2016 Plastics Determination of water content
    ISO 11357-6:2008 Plastics Differential scanning calorimetry (DSC) Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT)
    ISO 4065:1996 Thermoplastics pipes Universal wall thickness table
    ISO 497:1973 Guide to the choice of series of preferred numbers and of series containing more rounded values of preferred numbers
    CEN/TS 1555-7 : 2013 PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS POLYETHYLENE (PE) - PART 7: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY
    ISO 4437-3:2014 Plastics piping systems for the supply of gaseous fuels Polyethylene (PE) Part 3: Fittings
    ISO 6259-3:2015 Thermoplastics pipes Determination of tensile properties Part 3: Polyolefin pipes
    ISO 760:1978 Determination of water — Karl Fischer method (General method)
    ISO 11413:2008 Plastics pipes and fittings Preparation of test piece assemblies between a polyethylene (PE) pipe and an electrofusion fitting
    ISO 1043-1:2011 Plastics Symbols and abbreviated terms Part 1: Basic polymers and their special characteristics
    EN 12099 : 1997 PLASTICS PIPING SYSTEMS - POLYETHYLENE PIPING MATERIALS AND COMPONENTS - DETERMINATION OF VOLATILE CONTENT
    ISO 1167-1:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective