We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • BS ISO 8085-3 : 2001

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    POLYETHYLENE FITTINGS FOR USE WITH POLYETHYLENE PIPES FOR THE SUPPLY OF GASEOUS FUELS - METRIC SERIES - SPECIFICATIONS - PART 3: ELECTROFUSION FITTINGS

    Available format(s):  Hardcopy, PDF

    Superseded date:  31-01-2014

    Language(s):  English

    Published date:  01-01-2001

    Publisher:  British Standards Institution

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Symbols
    5 Material
    6 General requirements
    7 Geometrical characteristics
    8 Mechanical characteristics
    9 Physical characteristics
    10 Technical file
    11 Marking
    12 Packaging
    Annex A (informative) Examples of typical connector sockets
            for electrofusion fittings
    Annex B (normative) Formulae for calculating the equivalent
            dimensions of non-metric fitting series
    Annex C (normative) Short-term pressure test method
    Annex D (normative) Tensile test for fitting/pipe assemblies
    Bibliography

    Abstract - (Show below) - (Hide below)

    Gives the requirements for polyethylene electrofusion fittings intended to be used with PE pipes and fittings for the supply of gaseous fuels.

    General Product Information - (Show below) - (Hide below)

    Committee PRI/88/2
    Development Note Supersedes 00/122205 DC (12/2001)
    Document Type Standard
    Publisher British Standards Institution
    Status Superseded
    Superseded By
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    EN 682:2002/A1:2005 ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR SEALS USED IN PIPES AND FITTINGS CARRYING GAS AND HYDROCARBON FLUIDS
    ISO 8085-2:2001 Polyethylene fittings for use with polyethylene pipes for the supply of gaseous fuels Metric series Specifications Part 2: Spigot fittings for butt fusion, for socket fusion using heated tools and for use with electrofusion fittings
    ISO 6964:1986 Polyolefin pipes and fittings Determination of carbon black content by calcination and pyrolysis Test method and basic specification
    ISO 13477:2008 Thermoplastics pipes for the conveyance of fluids Determination of resistance to rapid crack propagation (RCP) Small-scale steady-state test (S4 test)
    ISO 3:1973 Preferred numbers Series of preferred numbers
    ISO 18553:2002 Method for the assessment of the degree of pigment or carbon black dispersion in polyolefin pipes, fittings and compounds
    ISO/TS 10839:2000 Polyethylene pipes and fittings for the supply of gaseous fuels Code of practice for design, handling and installation
    ISO 13957:1997 Plastics pipes and fittings Polyethylene (PE) tapping tees Test method for impact resistance
    ISO 13479:2009 Polyolefin pipes for the conveyance of fluids Determination of resistance to crack propagation Test method for slow crack growth on notched pipes
    IEC 60364-1:2005 Low-voltage electrical installations - Part 1: Fundamental principles, assessment of general characteristics, definitions
    ISO 12176-2:2008 Plastics pipes and fittings Equipment for fusion jointing polyethylene systems Part 2: Electrofusion
    ISO 12162:2009 Thermoplastics materials for pipes and fittings for pressure applications Classification, designation and design coefficient
    ISO 13478:2007 Thermoplastics pipes for the conveyance of fluids Determination of resistance to rapid crack propagation (RCP) Full-scale test (FST)
    ISO 3126:2005 Plastics piping systems Plastics components Determination of dimensions
    ASTM D 4019 : 1994 : REV A Standard Test Method for Moisture in Plastics by Coulometric Regeneration of Phosphorus Pentoxide (Withdrawn 2002)
    IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
    ISO 13954:1997 Plastics pipes and fittings Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm
    ISO 9356:1989 Polyolefin pipe assemblies with or without jointed fittings Resistance to internal pressure Test method
    ISO 13955:1997 Plastics pipes and fittings Crushing decohesion test for polyethylene (PE) electrofusion assemblies
    ISO/TR 10837:1991 Determination of the thermal stability of polyethylene (PE) for use in gas pipes and fittings
    ISO 1872-1:1993 Plastics Polyethylene (PE) moulding and extrusion materials Part 1: Designation system and basis for specifications
    ISO 497:1973 Guide to the choice of series of preferred numbers and of series containing more rounded values of preferred numbers
    EN 12117 : 1997 PLASTICS PIPING SYSTEMS - FITTINGS, VALVES AND ANCILLARIES - DETERMINATION OF GASEOUS FLOW RATE/PRESSURE DROP RELATIONSHIPS
    ISO 11413:2008 Plastics pipes and fittings Preparation of test piece assemblies between a polyethylene (PE) pipe and an electrofusion fitting
    ISO 1133:2005 Plastics Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics
    ISO 13951:2015 Plastics piping systems Test method for the resistance of plastic pipe/pipe or pipe/fitting assemblies to tensile loading
    ISO 4437:2007 Buried polyethylene (PE) pipes for the supply of gaseous fuels Metric series Specifications
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective