Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

PD ISO/TR 16335:2013

Current
Current

The latest, up-to-date edition.

Corrosion of metals and alloys. Corrosion tests in artificial atmospheres. Guidelines for selection of accelerated corrosion test for product qualification
Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

30-09-2013

Foreword
Introduction
1 Scope
2 Normative references
3 Categories and characteristics of accelerated corrosion
  tests
4 Recommended fields of application for different kinds of
  tests and their suitability
5 Corrosivity of tests and relative corrosion rates of standard
  metals
6 Requirements for test equipment and reproducibility of test
  results
7 Recommended procedures for product qualification
Annex A (informative) - Characteristics of standardized
        accelerated atmospheric corrosion tests
Annex B (informative) - Initial risk analysis of potential
        failure modes for products or functional units
Bibliography

Pertains for the selection of suitable accelerated atmospheric corrosion tests for qualification of products with metallic materials without or with permanent corrosion protection or temporary corrosion protection.

This Technical Report is applicable for the selection of suitable accelerated atmospheric corrosion tests for qualification of products with metallic materials without or with permanent corrosion protection or temporary corrosion protection. The characteristics of a number of standardized accelerated corrosion tests are also given to serve as a guide in the preparation of test specifications.

In this Technical Report the following aspects are taken into account:

  • Categories of accelerated atmospheric corrosion tests

  • Recommended fields of application for the different kinds of tests and their suitability

  • Corrosivity of tests and relative corrosion rates of standard metals

  • Requirements for test equipment, criteria for reproducibility and correlation with in-service performance

  • Recommended procedures for product qualification

The main purpose of this Technical Report is to present a framework for comparing the different accelerated corrosion test methods, which presently are available as International Standards. The suitability of a test method varies with the requirements set by the intended application of the product.

Committee
ISENFE/8
DocumentType
Standard
Pages
28
PublisherName
British Standards Institution
Status
Current

Standards Relationship
ISO/TR 16335:2013 Identical

ISO 16151:2005 Corrosion of metals and alloys Accelerated cyclic tests with exposure to acidified salt spray, "dry" and "wet" conditions
ISO 9223:2012 Corrosion of metals and alloys — Corrosivity of atmospheres — Classification, determination and estimation
ISO 11997-2:2013 Paints and varnishes — Determination of resistance to cyclic corrosion conditions — Part 2: Wet (salt fog)/dry/humidity/UV light
ISO 11130:2010 Corrosion of metals and alloys Alternate immersion test in salt solution
ISO 9226:2012 Corrosion of metals and alloys — Corrosivity of atmospheres — Determination of corrosion rate of standard specimens for the evaluation of corrosivity
IEC 60068-2-60:2015 RLV Environmental testing - Part 2-60: Tests - Test Ke: Flowing mixed gas corrosion test
IEC 60812:2006 Analysis techniques for system reliability - Procedure for failure mode and effects analysis (FMEA)
MIL-STD-810 Revision G:2008 ENVIRONMENTAL ENGINEERING CONSIDERATIONS AND LABORATORY TESTS
ISO 9224:2012 Corrosion of metals and alloys — Corrosivity of atmospheres — Guiding values for the corrosivity categories
IEC 60068-2-11:1981 Basic environmental testing procedures - Part 2-11: Tests - Test Ka: Salt mist
ISO 9225:2012 Corrosion of metals and alloys — Corrosivity of atmospheres — Measurement of environmental parameters affecting corrosivity of atmospheres
ISO 14993:2001 Corrosion of metals and alloys Accelerated testing involving cyclic exposure to salt mist, "dry" and "wet" conditions
ISO 21207:2015 Corrosion tests in artificial atmospheres — Accelerated corrosion tests involving alternate exposure to corrosion-promoting gases, neutral salt-spray and drying
ISO 16701:2015 Corrosion of metals and alloys Corrosion in artificial atmosphere Accelerated corrosion test involving exposure under controlled conditions of humidity cycling and intermittent spraying of a salt solution
ISO 11997-1:2017 Paints and varnishes — Determination of resistance to cyclic corrosion conditions — Part 1: Wet (salt fog)/dry/humid
ISO 10062:2006 Corrosion tests in artificial atmosphere at very low concentrations of polluting gas(es)
ISO 9227:2017 Corrosion tests in artificial atmospheres — Salt spray tests
ISO 20340:2009 Paints and varnishes Performance requirements for protective paint systems for offshore and related structures
ISO 11844-1:2006 Corrosion of metals and alloys Classification of low corrosivity of indoor atmospheres Part 1: Determination and estimation of indoor corrosivity
IEC 60068-2-52:2017 Environmental testing - Part 2-52: Tests - Test Kb: Salt mist, cyclic (sodium chloride solution)
ISO 11474:1998 Corrosion of metals and alloys Corrosion tests in artificial atmosphere Accelerated outdoor test by intermittent spraying of a salt solution (Scab test)
IEC 60068-2-30:2005 Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle)

View more information
$407.85
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more