We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • CEN ISO/TS 22391-7 : 2011

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - POLYETHYLENE OF RAISED TEMPERATURE RESISTANCE (PE-RT) - PART 7: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY (ISO/TS 22391-7:2011)

    Available format(s): 

    Superseded date:  15-01-2019

    Language(s): 

    Published date:  12-01-2013

    Publisher:  Comite Europeen de Normalisation

    Add to Watchlist
    Pure ENs are not available for sale, please purchase a suitable national adoption

    Sorry this product is not available in your region.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Abbreviated terms
    5 General
    6 Testing and inspection
    Bibliography

    Abstract - (Show below) - (Hide below)

    Provides guidance on the assessment of conformity of products and assemblies in accordance with other applicable part(s) of ISO 22391 intended to be included in the manufacturer's quality plan as part of the quality management system and for the establishment of certification procedures.

    General Product Information - (Show below) - (Hide below)

    Committee TC 155
    Document Type Standard
    Publisher Comite Europeen de Normalisation
    Status Superseded
    Superseded By

    Standards Referenced By This Book - (Show below) - (Hide below)

    14/30297462 DC : 0 BS EN 15015 - PLASTICS PIPING SYSTEMS - HOT AND COLD WATER PIPING COMPONENTS - REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR PIPES AND FITTINGS
    PREN 15015 : DRAFT 2014 PLASTICS PIPING SYSTEMS - HOT AND COLD WATER PIPING COMPONENTS - REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR PIPES AND FITTINGS

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO/IEC 17025:2005 General requirements for the competence of testing and calibration laboratories
    ISO 3951-1:2013 Sampling procedures for inspection by variables Part 1: Specification for single sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection for a single quality characteristic and a single AQL
    ISO/IEC 17021:2011 Conformity assessment Requirements for bodies providing audit and certification of management systems
    ISO 22391-5:2009 Plastics piping systems for hot and cold water installations Polyethylene of raised temperature resistance (PE-RT) Part 5: Fitness for purpose of the system
    ISO 2859-2:1985 Sampling procedures for inspection by attributes Part 2: Sampling plans indexed by limiting quality (LQ) for isolated lot inspection
    ISO 22391-2:2009 Plastics piping systems for hot and cold water installations Polyethylene of raised temperature resistance (PE-RT) Part 2: Pipes
    ISO/IEC 17020:2012 Conformity assessment Requirements for the operation of various types of bodies performing inspection
    ISO 3951-3:2007 Sampling procedures for inspection by variables Part 3: Double sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection
    ISO 9001:2015 Quality management systems Requirements
    ISO 9000:2015 Quality management systems Fundamentals and vocabulary
    ISO 22391-3:2009 Plastics piping systems for hot and cold water installations Polyethylene of raised temperature resistance (PE-RT) Part 3: Fittings
    ISO/IEC Guide 65:1996 General requirements for bodies operating product certification systems
    ISO 22391-1:2009 Plastics piping systems for hot and cold water installations Polyethylene of raised temperature resistance (PE-RT) Part 1: General
    ISO 3951-5:2006 Sampling procedures for inspection by variables Part 5: Sequential sampling plans indexed by acceptance quality limit (AQL) for inspection by variables (known standard deviation)
    ISO 3951-2:2013 Sampling procedures for inspection by variables Part 2: General specification for single sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection of independent quality characteristics
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective