Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

DEFSTAN 05-133(PT1)/1(2011) : 2011

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

METHODS FOR TESTING PAINTS, CHEMICALS AND ASSOCIATED PRODUCTS - PART 1: PAINTS AND ALLIED PRODUCTS
Available format(s)

Hardcopy , PDF

Superseded date

28-01-2020

Language(s)

English

Published date

01-01-2011

1 Scope
2 Warning
3 Normative References
4 Abbreviations
5 Synopsis of Grouping Different Category of Tests
6 Tests Performed on Liquid Paint and Removers
7 Physical Tests Performed on the Dry Paint Film
8 Immersion Tests Performed on the Dry Paint Film
9 Environmental Tests Performed on the Dry Paint Film

Describes a compendium of test methods used to test paint and allied products within paint related Defence Standards in the Defence Standard 80 series.

DevelopmentNote
This standard is obsolescent because it is no longer required for procurement of new equipment but is retained for maintenance purposes in support of existing in-service equipment. (11/2016)
DocumentType
Standard
Pages
32
PublisherName
UK Ministry of Defence Standards
Status
Superseded
SupersededBy

DEFSTAN 80-213/3(2017) : 2017 PAINT, FINISHING, POLYURETHANE, MULTI-PACK, ANTI-SLIP, FOR LAND VEHICLES, LOW VOC
DEFSTAN 80-125/5(2017) : 2017 PAINT, FINISHING, EMULSION FOR CANVAS TYPES: BRUSHING OR SPRAYING
DEFSTAN 80-037/4(2017) : 2017 PAINT, FINISHING, OIL-RESISTING TYPES: BRUSHING OR SPRAYING
DEFSTAN 80-215/3(2017) : 2017 PAINT, FINISHING, TEMPORARY COLOUR, ALKALI REMOVABLE, NON-AEROSPACE USE
DEFSTAN 80-218/3(2017) : 2017 TEMPORARY COLOUR COATING (TCC) REMOVER, NON-AIRCRAFT USE
DEFSTAN 80-031/6(2017) : 2017 PAINT, FINISHING, GENERAL SERVICE, ALUMINIUM - TYPE: BRUSHING OR SPRAYING
DEFSTAN 80-054/6(2017) : 2017 PAINT, FINISHING, GENERAL SERVICE, FUEL RESISTANT, GLOSS - TYPE: BRUSHING OR SPRAYING
DEFSTAN 80-168/5(2017) : 2017 COMPOUND, PROTECTIVE, FOR VEHICLE UNDERBODIES, WATER-BASED
DEFSTAN 80-124/3(2017) : 2017 PAINT, PRIMING, DEFENCE EQUIPMENT, STOVING - TYPES: SPRAYING AND DIPPING
DEFSTAN 80-065/4(2017) : 2017 PAINT, FINISHING, FOR THE INTERIOR OF JERRICANS
DEFSTAN 80-131/3(2017) : 2017 PAINT, ALUMINIUM, HEAT RESISTING - TYPE: BRUSHING

BS EN ISO 1514:2004 Paints and varnishes. Standard panels for testing
BS EN ISO 1518:2001 Paints and varnishes. Scratch test
BS EN ISO 3696:1995 Water for analytical laboratory use. Specification and test methods
BS 2X 34:1998 Specification for two component polyurethane finish for aerospace purposes
BS EN 23270:1991 Specification for temperatures and humidities for conditioning and testing paints, varnishes and their raw materials
BS EN ISO 7539-5:1995 Corrosion of metals and alloys. Stress corrosion testing Method for the preparation and use of C-ring specimens
BS EN 10111:2008 Continuously hot rolled low carbon steel sheet and strip for cold forming. Technical delivery conditions
BS EN 2832:1993 Hydrogen embrittlement of steels. Notched specimen test
BS 410-1:2000 Test sieves. Technical requirements and testing Test sieves of metal wire cloth
ISO 11507:2007 Paints and varnishes Exposure of coatings to artificial weathering Exposure to fluorescent UV lamps and water
BS EN ISO 2431:2011 Paints and varnishes. Determination of flow time by use of flow cups
BS 2L 97:1971 Specification for plate of aluminium-copper-magnesium-manganese alloy (solution treated, controlled stretched and aged at room temperature) (Cu 4.4, Mg 1.5, Mn 0.6)
BS EN ISO 2812-1:2007 Paints and varnishes. Determination of resistance to liquids Immersion in liquids other than water
DEFSTAN 91-25/4(2002) : 2002 LUBRICATING OIL, GEAR, NAVAL: LIGHT SERVICE NATO CODE: O-240 JOINT SERVICE DESIGNATION: OM-100
BS EN 10130:2006 Cold rolled low carbon steel flat products for cold forming. Technical delivery conditions
BS ISO 3116:2007 Magnesium and magnesium alloys. Wrought magnesium alloys
BS EN 1652:1998 Copper and copper alloys. Plate, sheet, strip and circles for general purposes
DEFSTAN 91-39/3(2001) : 2001 HYDRAULIC FLUID, PETROLEUM: ANTI-WEAR NATO CODE: H-576 JOINT SERVICE DESIGNATION: OM-33
DEFSTAN 03-2/6(2011) : 2011 CLEANING AND PREPARATION OF METAL SURFACES
BS 3L500(2011) : 2011 PROCEDURE FOR INSPECTION, TESTING AND ACCEPTANCE OF WROUGHT MAGNESIUM BASE ALLOYS
BS EN 29117:1992 Methods of test for paints. Tests associated with paint film formation Paints and varnishes. Determination of through-dry state and through-dry time. Method of test
BS EN 2395:2005 Aerospace series. Aluminium alloy AL-P2014A-T4 or T42. Sheet and strip. 0,4 mm ≤a ≤6 mm
BS L 168:1978 Specification for bars and extruded sections of aluminium-copper-magnesium-silicon-manganese alloy (solution treated and artificially aged) (not exceeding 200 mm diameter or minor sectional dimension) (Cu 4.4, Mg 0.5, Si 0.7, Mn 0.8)
BS EN ISO 2409:2013 Paints and varnishes. Cross-cut test
DTD 5592 : LATEST ACRYLIC SHEETS FOR AIRCRAFT GLAZING
DEFSTAN 91-48/2(1997) : 1997 HYDRAULIC FLUID, PETROLEUM: SUPERCLEAN NATO CODE: H-515 JOINT SERVICE DESIGNATION: OM-15 HYDRAULIC FLUID, PETROLEUM: NORMAL NATO CODE: H-520 JOINT SERVICE DESIGNATION: OM-18
BS 2X 33:1998 Specification for two component epoxy primer for aerospace purposes
DEFSTAN 03-19/4(2010) : 2010 ELECTRO-DEPOSITION OF CADMIUM

View more information
$26.52
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more