We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • DIN 5480-2:1991-10

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    INVOLUTE SPLINES BASED ON REFERENCE DIAMETERS - PART 2: NOMINAL AND INSPECTION DIMENSIONS

    Available format(s):  Hardcopy, PDF

    Superseded date:  14-03-2020

    Language(s):  English

    Published date:  01-01-1991

    Publisher:  German Institute for Standardisation (Deutsches Institut für Normung)

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    1 Scope
    2 Normative references
    3 Graphic representation of dimensions
       and measurements
       3.1 Space width/tooth thickness
       3.2 Diameters
       3.3 Inspection dime
    4 Module m = 0,5 mm
    5 Module m = 0,6 mm
    6 Module m = 0,75 mm
    7 Module m = 0,8 mm
    8 Module m = 1 mm
    9 Module m = 1,25 mm
    10 Module m = 1,5 mm
    11 Module m = 1,75 mm
    12 Module m = 2 mm
    13 Module m = 2,5 mm
    14 Module m = 3 mm
    15 Module m = 4 mm
    16 Module m = 5 mm
    17 Module m = 6 mm
    18 Module m = 8 mm
    19 Module m = 10 mm
    Bibliography
    Figures

    Abstract - (Show below) - (Hide below)

    Applies to involute splines and spline joints based on reference diameters for connecting hubs and shafts either with a removable connection, a sliding fit or a permanent fit.

    General Product Information - (Show below) - (Hide below)

    Development Note Supersedes DIN 5480-3 E, DIN 5480-4 E, DIN 5480-5 E, DIN 5480-6 E, DIN 5480-7 E, DIN 5480-8 E, DIN 5480-9 E, DIN 5480-10 E, DIN 5480-11 E, DIN 5480-12 E and DIN 5480-13 E. (01/2008) Suspended until publication of a revised English text, due to a new German edition. (03/2015)
    Document Type Standard
    Publisher German Institute for Standardisation (Deutsches Institut für Normung)
    Status Superseded

    Standards Referencing This Book - (Show below) - (Hide below)

    DIN 3977 E : 1981 MEASURING ELEMENT DIAMETERS FOR THE RADIAL OR DIAMETRAL DIMENSION FOR TESTING TOOTH THICKNESS OF CYLINDRICAL GEARS
    DIN ISO 6413:1990-03 TECHNICAL DRAWINGS - REPRESENTATION OF SPLINES AND SERRATIONS
    DIN 3961 E : 1978 TOLERANCES FOR CYLINDRICAL GEAR TEETH; BASES
    DIN 5480-1 E : 2006 INVOLUTE SPLINES BASED ON REFERENCE DIAMETERS - PART 1: GENERAL
    ISO 6413:1988 Technical drawings Representation of splines and serrations
    DIN 5466-1:2000-10 Splined joints, calculation of load capacity - Part 1: General basis
    ISO 54:1996 Cylindrical gears for general engineering and for heavy engineering Modules
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective