Name: DIN EN 12067-1:1998-12
Brand: DIN

DIN EN 12067-1:1998-12

Superseded

GAS/AIR RATIO CONTROLS FOR GAS BURNERS AND GAS BURNING APPLIANCES - PART 1: PNEUMATIC TYPES

Available format(s)

Hardcopy , PDF

Superseded date

01-06-2011

Language(s)

English

Published date

01-01-1998

Publisher

German Institute for Standardisation (Deutsches Institut für Normung)

Foreword
1 Scope
2 Normative references
3 Definitions
4 Construction requirements
5 Performance requirements
6 Test methods
7 Instructions and declarations
8 Marking
Annexes
A (informative) - Use of ISO 7-1: 1994 and ISO 228-1: 1994
  threads for gas connections
B (informative) - Leak tightness test - volumetric method
C (informative) - Leak tightness test - pressure loss method
D (informative) - Conversion of pressure loss into leakage
  rate
ZA (informative) - Clauses of this European Standard
   addressing essential requirements or other provisions
   of EU Directives

Describes the safety, construction and performance requirements for gas/air ratio controls for inlet pressures up to and including 500 mbar of nominal connection size up to and including DN 150, intended for use with gas appliances used with one or more fuel gases of the first, second and third families. Also describes the test procedures for evaluating these requirements and defines information necessary for use and installation.

DocumentType	Standard
Pages	38
PublisherName	German Institute for Standardisation (Deutsches Institut für Normung)
Status	Superseded

Standards	Relationship
UNE-EN 12067-1:1999	Identical
NBN EN 12067-1 : 99 AMD 1 2003	Identical
UNI EN 12067-1 : 2006	Identical
SN EN 12067-1 : 1999 AMD 1 2003	Identical
NF EN 12067-1 : 98 AMD 1 2003	Identical
NS EN 12067-1 : 1999 AMD 1 2003	Identical
NEN EN 12067-1 : 1998 AMD 1 2003	Identical
I.S. EN 12067-1:1999	Identical
EN 12067-1 : 98 AMD 1 2003	Identical
BS EN 12067-1:1999	Identical

EN 60998-2-2:2004	Connecting devices for low-voltage circuits for household and similar purposes - Part 2-2: Particular requirements for connecting devices as separate entities with screwless-type clamping units
ISO 274:1975	Copper tubes of circular section — Dimensions
EN 60998-2-1:2004	Connecting devices for low-voltage circuits for household and similar purposes - Part 2-1: Particular requirements for connecting devices as separate entities with screw-type clamping units
EN 161:2011+A3:2013	Automatic shut-off valves for gas burners and gas appliances
ISO 262:1998	ISO general purpose metric screw threads — Selected sizes for screws, bolts and nuts
ISO 7-1:1994	Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation
EN 60529:1991/AC:2016-12	DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
ISO 301:2006	Zinc alloy ingots intended for castings
ISO 228-1:2000	Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation
EN 60730-1:2016	Automatic electrical controls - Part 1: General requirements
ISO 1817:2015	Rubber, vulcanized or thermoplastic Determination of the effect of liquids