Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

DIN EN 60296 : 2012

Current
Current

The latest, up-to-date edition.

FLUIDS FOR ELECTROTECHNICAL APPLICATIONS - UNUSED MINERAL INSULATING OILS FOR TRANSFORMERS AND SWITCHGEAR (IEC 60296:2012)
Available format(s)

Hardcopy

Language(s)

German

Published date

01-12-2012

FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Properties of oil
  4.1 Functional properties
  4.2 Refining and stability
  4.3 Performance
  4.4 Health, safety and environment (HSE) properties
5 Classification, identification, general delivery
  requirements and sampling
  5.1 Classification
  5.2 Requirements
  5.3 Mixability
  5.4 Identification and general delivery requirements
  5.5 Sampling
6 Properties, their significance and test methods
  6.1 Viscosity
  6.2 Pour point
  6.3 Water content
  6.4 Breakdown voltage
  6.5 Dielectric dissipation factor (DDF)
  6.6 Appearance
  6.7 Acidity
  6.8 Interfacial tension (IFT)
  6.9 Sulfur content
  6.10 Corrosive sulfur
  6.11 Antioxidant additive content
  6.12 Oxidation stability
  6.13 Gassing
  6.14 Electrostatic charging tendency (ECT)
  6.15 Flash point
  6.16 Density
  6.17 Polycyclic aromatics (PCA)
  6.18 Polychlorinated biphenyls (PCB)
  6.19 2-Furfural and related compounds (2-FAL)
7 Specific requirements for special applications
  7.1 Higher oxidation stability and low sulfur content
  7.2 Electrostatic charging tendency (ECT)
  7.3 Gassing
Annex ZA (normative) Normative references to international
                     publications with their corresponding
                     European publications
Annex ZB (normative) Special national conditions
Bibliography

DevelopmentNote
Supersedes DIN 57370-1 and DIN VDE 0370-1. (01/2005) Supersedes DIN IEC 60296. (01/2013)
DocumentType
Standard
Pages
0
PublisherName
Verband Deutscher Elektrotechniker
Status
Current
SupersededBy
Supersedes

Standards Relationship
NBN EN 60296 : 2012 Identical
VDE 0370-1 : 2012 Corresponds
UNE-EN 60296:2012 Identical
EN 60296:2012 Identical
IEC 60296:2012 RLV Identical
I.S. EN 60296:2012 Identical
NF EN 60296 : 2014 Identical
BS EN 60296:2012 Identical

DIN EN ISO 17855-2:2016-06 PLASTICS - POLYETHYLENE (PE) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 17855-2:2016)
DIN EN ISO 15103-2:2007-09 PLASTICS - POLY(PHENYLENE ETHER) (PPE) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
DIN EN ISO 1872-2:2000-12 PLASTICS - POLYETHYLENE (PE) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
DIN EN ISO 175:2011-03 Plastics - Methods of test for the determination of the effects of immersion in liquid chemicals (ISO 175:2010)
DIN EN ISO 19069-2:2016-07 PLASTICS - POLYPROPYLENE (PP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 19069-2:2016)
DIN EN ISO 17855-2 E : 2016 PLASTICS - POLYETHYLENE (PE) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 17855-2:2016)
DIN EN ISO 1874-2:2013-03 PLASTICS - POLYAMIDE (PA) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 1874-2:2012)
DIN EN ISO 8986-2 E : 2010 PLASTICS - POLYBUTENE-1 (PB-1) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
DIN EN ISO 19069-2 E : 2016 PLASTICS - POLYPROPYLENE (PP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 19069-2:2016)
DIN EN ISO 20028-2 E : 2017 PLASTICS - THERMOPLASTIC POLYESTER (TP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 20028-2:2017)
DIN EN ISO 16396-2:2017-07 Plastics - Polyamide (PA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 16396-2:2017)
DIN EN ISO 25137-2 E : 2017 PLASTICS - SULFONE POLYMER MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 25137-2:2009)
DIN EN ISO 16396-2 E : 2017 PLASTICS - POLYAMIDE (PA) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 16396-2:2017)
DIN EN ISO 20028-2:2015-08 (Draft) PLASTICS - THERMOPLASTIC POLYESTER (TP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 20028-2:2017)
DIN EN ISO 11542-2:2010-01 Plastics - Ultra-high-molecular-weight polyethylene (PE-UHMW) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 11542-2:1998 + Cor. 1:2007) (includes Corrigendum AC:2008)
DIN EN ISO 175 E : 2011 PLASTICS - METHODS OF TEST FOR THE DETERMINATION OF THE EFFECTS OF IMMERSION IN LIQUID CHEMICALS
DIN EN ISO 25137-2:2016-08 (Draft) PLASTICS - SULFONE POLYMER MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 25137-2:2009)
DIN EN ISO 8986-2:2010-04 PLASTICS - POLYBUTENE-1 (PB-1) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES

View more information
$178.00
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more