Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

DIN EN 60664-1 : 2008

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

INSULATION COORDINATION FOR EQUIPMENT WITHIN LOW-VOLTAGE SYSTEMS - PART 1: PRINCIPLES, REQUIREMENTS AND TESTS
Available format(s)

Hardcopy

Superseded date

02-07-2022

Language(s)

German

Published date

01-01-2008

INTRODUCTION
SECTION 1: GENERAL AND DEFINITIONS
1.1 Scope
1.2 Normative references
1.3 Definitions
SECTION 2: BASIS FOR INSULATION COORDINATION
2.1 Basic principles
2.2 Voltages and voltage ratings
2.3 Frequency
2.4 Time under voltage stress
2.5 Pollution
2.6 Information supplied with the equipment
2.7 Insulating material
SECTION 3: REQUIREMENTS AND DIMENSIONING RULES
3.1 Dimensioning of clearances
3.2 Dimensioning of creepage distances
3.3 Requirements for design of solid insulation
SECTION 4: TESTS AND MEASUREMENTS
4.1 Tests
4.2 Measurement of creepage distances and clearances
Annex A (informative) - Basic data on withstand characteristics
                        of clearances
Annex B (informative) - Nominal voltages of supply systems
                        for different modes of overvoltage
                        control
Annex C (informative) - Partial discharge test methods
Annex D (informative) - Additional information on partial
                        discharge test methods
Annex E (informative) - Comparison of creepage distances specified
                        in table 4 and clearances in table A.1
Annex ZA (normative) - Normative references to international
                        publications with their corresponding
                        European publications
Figures
Tables

Defines the requirements for clearances, creepage distances and solid insulation for equipment based upon their performance criteria. It includes methods of electric testing with respect to insulation coordination. It also deals with insulation coordination for equipment within low-voltage systems. Applies to equipment for use up to 2000 m above sea level having a rated voltage up to a.c. 1000 V with rated frequencies up to 30 kHz, or a rated voltage up to d.c. 1500 V.

DevelopmentNote
Supersedes DIN IEC 28A-121-CD, DIN IEC 28A-142-CD and DIN VDE 0110-1. (12/2003) Supersedes DIN IEC 60664-1. (01/2008)
DocumentType
Standard
Pages
81
PublisherName
Verband Deutscher Elektrotechniker
Status
Superseded
SupersededBy
Supersedes

Standards Relationship
BS EN 60664-1:2007 Identical
I.S. EN 60664-1:2007 Identical
EN 60664-1:2007 Identical
IEC 60664-1:2007 Identical
UNE-EN 60664-1:2008 Identical
NF EN 60664-1 : 2007 Identical
NBN EN 60664-1 : 2007 Identical
VDE 0110-1 : 2008 Corresponds

DIN EN ISO 13856-2:2013-08 SAFETY OF MACHINERY - PRESSURE-SENSITIVE PROTECTIVE DEVICES - PART 2: GENERAL PRINCIPLES FOR THE DESIGN AND TESTING OF PRESSURE-SENSITIVE EDGES AND PRESSURE-SENSITIVE BARS (ISO 13856-2:2013)
DIN EN ISO 13856-3 E : 2013 SAFETY OF MACHINERY - PRESSURE-SENSITIVE PROTECTIVE DEVICES - PART 3: GENERAL PRINCIPLES FOR DESIGN AND TESTING OF PRESSURE-SENSITIVE BUMPERS, PLATES, WIRES AND SIMILAR DEVICES (ISO 13856-3:2013)
DIN 16196:2015-03 DIAL INDICATING THERMOMETERS WITH ELECTRICAL LIMIT CONTACT DEVICES - FILLED SYSTEM THERMOMETERS AND BIMETALLIC THERMOMETERS
DIN EN 1760-2:2001-07 SAFETY OF MACHINERY - PRESSURE SENSITIVE PROTECTIVE DEVICES - PART 2: GENERAL PRINCIPLES FOR THE DESIGN AND TESTING OF PRESSURE SENSITIVE EDGES AND PRESSURE SENSITIVE BARS
VDI/VDE/DGQ/DKD 2622 Blatt 20:2013-12 Calibration of measuring equipment for electrical quantities - Direct-voltage measuring amplifiers
KTA 3403 : 2015(R2017) CABLE PENETRATIONS THROUGH THE REACTOR CONTAINMENT VESSEL OF NUCLEAR POWER PLANTS
VDI 3819 Blatt 2:2013-07 Fire protection building services - Functions and correlations
DIN 19704-3:2014-11 HYDRAULIC STEEL STRUCTURES - PART 3: ELECTRICAL EQUIPMENT
DIN EN ISO 669 E : 2016 RESISTANCE WELDING - RESISTANCE WELDING EQUIPMENT - MECHANICAL AND ELECTRICAL REQUIREMENTS (ISO 669:2016)
DIN EN ISO 669:2016-07 RESISTANCE WELDING - RESISTANCE WELDING EQUIPMENT - MECHANICAL AND ELECTRICAL REQUIREMENTS (ISO 669:2016)
DIN EN ISO 5826:2014-07 RESISTANCE WELDING EQUIPMENT - TRANSFORMERS - GENERAL SPECIFICATIONS APPLICABLE TO ALL TRANSFORMERS (ISO 5826:2014)
DIN EN ISO 13856-3:2013-12 SAFETY OF MACHINERY - PRESSURE-SENSITIVE PROTECTIVE DEVICES - PART 3: GENERAL PRINCIPLES FOR DESIGN AND TESTING OF PRESSURE-SENSITIVE BUMPERS, PLATES, WIRES AND SIMILAR DEVICES (ISO 13856-3:2013)
DIN EN 1760-2:2009-08 SAFETY OF MACHINERY - PRESSURE SENSITIVE PROTECTIVE DEVICES - PART 2: GENERAL PRINCIPLES FOR THE DESIGN AND TESTING OF PRESSURE SENSITIVE EDGES AND PRESSURE SENSITIVE BARS

View more information
$333.44
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more