We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • DIN EN ISO 11296-7 E : 2013

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 7: LINING WITH SPIRALLY-WOUND PIPES (ISO 11296-7:2011)

    Available format(s):  Hardcopy, PDF

    Superseded date:  09-11-2019

    Language(s):  English

    Published date:  01-01-2013

    Publisher:  German Institute for Standardisation (Deutsches Institut für Normung)

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    National foreword
    National Annex NA (informative) - Bibliography
    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Symbols and abbreviated terms
    5 Pipes at the "M" stage
    6 Fittings at the "M" stage
    7 Ancillary components
    8 Fitness for purpose of the installed lining
      system at the "I" stage
    9 Installation practice
    Annex A (normative) - Spirally-wound pipe - Test
            method for watertightness in a deflected
            condition
    Annex B (informative) - Examples of methods
            for reconnecting and sealing laterals to
            SWO pipe
    Bibliography

    Abstract - (Show below) - (Hide below)

    Describes requirements and test methods for pipes which are formed on site by spirally winding and jointing a pre-manufactured profiled plastics strip, or a profiled plastics strip and integral locking joiner strip, and used for the renovation of underground non-pressure drainage and sewerage networks.

    General Product Information - (Show below) - (Hide below)

    Development Note Supersedes DIN EN 13566-7 E. (07/2013)
    Document Type Standard
    Publisher German Institute for Standardisation (Deutsches Institut für Normung)
    Status Superseded
    Superseded By

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 7619-1:2010 Rubber, vulcanized or thermoplastic Determination of indentation hardness Part 1: Durometer method (Shore hardness)
    DIN EN ISO 9967 E : 2016 THERMOPLASTICS PIPES - DETERMINATION OF CREEP RATIO (ISO 9967:2016)
    ISO 11295:2017 Classification and information on design and applications of plastics piping systems used for renovation and replacement
    DIN EN ISO 306 E : 2014 PLASTICS - THERMOPLASTIC MATERIALS - DETERMINATION OF VICAT SOFTENING TEMPERATURE (VST) (ISO 306:2013)
    ISO 527-2:2012 Plastics Determination of tensile properties Part 2: Test conditions for moulding and extrusion plastics
    ISO 11296-1:2009 Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks Part 1: General
    ISO 6259-1:2015 Thermoplastics pipes Determination of tensile properties Part 1: General test method
    EN 1979 : 1999 PLASTICS PIPING AND DUCTING SYSTEMS - THERMOPLASTICS SPIRALLY-FORMED STRUCTURED-WALL PIPES - DETERMINATION OF THE TENSILE STRENGTH OF A SEAM
    DIN EN ISO 9969 E : 2016 THERMOPLASTICS PIPES - DETERMINATION OF RING STIFFNESS (ISO 9969:2016)
    ISO 11296-4:2009 Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks Part 4: Lining with cured-in-place pipes
    ISO 179-1:2010 Plastics Determination of Charpy impact properties Part 1: Non-instrumented impact test
    ISO 306:2013 Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST)
    ISO 4948-2:1981 Steels Classification Part 2: Classification of unalloyed and alloy steels according to main quality classes and main property or application characteristics
    ISO 4435:2003 Plastics piping systems for non-pressure underground drainage and sewerage Unplasticized poly(vinyl chloride) (PVC-U)
    ISO 9967:2016 Thermoplastics pipes Determination of creep ratio
    ISO 37:2017 Rubber, vulcanized or thermoplastic Determination of tensile stress-strain properties
    EN 14364:2013 PLASTICS PIPING SYSTEMS FOR DRAINAGE AND SEWERAGE WITH OR WITHOUT PRESSURE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON UNSATURATED POLYESTER RESIN (UP) - SPECIFICATIONS FOR PIPES, FITTINGS AND JOINTS
    ISO 9969:2016 Thermoplastics pipes Determination of ring stiffness
    ISO 527-1:2012 Plastics Determination of tensile properties Part 1: General principles
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective