DIN EN ISO 14253-1:2013-12
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Hardcopy , PDF
07-03-2021
German, English
01-01-2013
This standard is included in DIN Handbook 11-1 and 303.
DevelopmentNote |
DRAFT 2016 issued in July 2016. (07/2016)
|
DocumentType |
Standard
|
Pages |
21
|
PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
Status |
Superseded
|
SupersededBy |
Standards | Relationship |
ISO 14253-1:2017 | Identical |
NBN EN ISO 14253-1 : 2013 | Identical |
I.S. EN ISO 14253-1:2013 | Identical |
SN EN ISO 14253-1 : 2013 | Identical |
UNI EN ISO 14253-1 : 2013 | Identical |
ONORM EN ISO 14253-1 : 2014 | Identical |
BS EN ISO 14253-1:2013 | Identical |
UNE-EN ISO 14253-1:2015 | Identical |
NS EN ISO 14253-1 : 2017 | Identical |
NEN EN ISO 14253-1 : 2018 | Identical |
EN ISO 14253-1:2017 | Identical |
NF EN ISO 14253-1 : 2017 | Identical |
I.S. EN ISO 14253-1:2017 | Identical |
DIN 874-1:2003-11 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - STRAIGHT EDGES - PART 1: STEEL STRAIGHT EDGES - DIMENSIONS, TECHNICAL DELIVERY CONDITIONS |
DIN EN ISO 10360-7:2011-09 | Geometrical product specifications (GPS) - Acceptance and reverification tests for coordinate measuring machines (CMM) - Part 7: CMMs equipped with imaging probing systems (ISO 10360-7:2011) |
DIN 863-1:2016-07 (Draft) | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - MICROMETERS - PART 1: MICROMETERS FOR EXTERNAL MEASUREMENTS; MAXIMUM PERMISSIBLE ERRORS |
DIN 874-2:2003-11 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - STRAIGHT EDGES - PART 2: KNIFE EDGE STRAIGHT EDGES - DIMENSIONS, TECHNICAL DELIVERY CONDITIONS |
DIN EN ISO 11137-3:2015-08 (Draft) | STERILIZATION OF HEALTH CARE PRODUCTS - RADIATION - PART 3: GUIDANCE ON DOSIMETRIC ASPECTS OF DEVELOPMENT, VALIDATION AND ROUTINE CONTROL (ISO 11137-3:2017) |
DIN EN ISO 463 : 2009-07 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL MEASURING EQUIPMENT - DESIGN AND METROLOGICAL CHARACTERISTICS OF MECHANICAL DIAL GAUGES |
VDI/VDE 2660 Blatt 1:2010-07 | Experimental stress analysis - Optical strain sensor based on fibre Bragg grating - Fundamentals, characteristics and sensor testing |
VDI/VDE 2617 Blatt 6.1:2007-05 | Accuracy of coordinate measuring machines - Characteristics and their testing - Coordinate measuring machines with optical probing - Code of practice for the application of DIN EN ISO 10360 to coordinate measuring machines with optical sensors for lateral structures |
VDI/VDE 2617 Blatt 4:2006-05 | Accuracy of coordinate measuring machines - Characteristics and their checking - Manual for the use of DIN EN ISO 10360-3 for coordinate measuring machines with additional axes of rotation |
DIN EN ISO 2538-2:2015-01 | Geometrical product specifications (GPS) - Wedges - Part 2: Dimensioning and tolerancing (ISO 2538-2:2014) |
DIN HDBK 303 : 2ED 2008 | |
DIN EN ISO 11608-5:2013-01 | Needle-based injection systems for medical use - Requirements and test methods - Part 5: Automated functions (ISO 11608-5:2012) |
DIN CEN ISO/TS 8062-2;DIN SPEC 91184:2014-03 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL AND GEOMETRICAL TOLERANCES FOR MOULDED PARTS - PART 2: RULES (ISO/TS 8062-2:2013) |
DIN EN ISO 8015:2011-09 | Geometrical product specifications (GPS) - Fundamentals - Concepts, principles and rules (ISO 8015:2011) |
DIN EN ISO 13385-1:2011-12 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL MEASURING EQUIPMENT - PART 1: CALLIPERS; DESIGN AND METROLOGICAL CHARACTERISTICS (ISO 13385-1:2011) |
DIN EN ISO 25178-605:2014-06 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - SURFACE TEXTURE: AREAL - PART 605: NOMINAL CHARACTERISTICS OF NON-CONTACT (POINT AUTOFOCUS PROBE) INSTRUMENTS (ISO 25178-605:2014) |
DIN EN ISO 12781-1:2011-07 | Geometrical product specifications (GPS) - Flatness - Part 1: Vocabulary and parameters of flatness (ISO 12781-1:2011) |
DIN EN ISO 10360-6:2009-01 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - ACCEPTANCE AND REVERIFICATION TESTS FOR COORDINATE MEASURING MACHINES (CMM) - PART 6: ESTIMATION OF ERRORS IN COMPUTING GAUSSIAN ASSOCIATED FEATURES |
VDI/VDE/DGQ 2618 Blatt 1.2:2003-12 | Inspection of measuring and test equipment - Instructions for the inspection of measuring and test equipment for geometrical quantities - Uncertainty of measurement |
VDI/VDE 2617 Blatt 10:2011-01 | Accuracy of coordinate measuring machines - Characteristics and their checking - Acceptance and reverification tests of lasertrackers |
VDI/VDE/DGQ/DKD 2622 Blatt 15.1:2011-10 | Calibration for measuring equipment for electrical quantities - Artificial mains networks |
VDI/VDE 2617 Blatt 7:2008-09 | Accuracy of coordinate measuring machines - Parameters and their checking - Estimation of measurement uncertainty of coordinate measuring machines by means of simulation |
VDI/VDE 2617 Blatt 5:2010-12 | Accuracy of coordinate measuring machines - Parameters and their reverification - Interim check with artefacts |
VDI/VDE 2600 Blatt 1:2013-10 | Inspection process management - Identification, classification and proof of suitability for inspection processes |
VDI/VDE 2617 Blatt 2.1:2014-03 | Accuracy of coordinate measuring machines - Parameters and their reverification - Code of practice for the application of DIN EN ISO 10360-2 for length measurement |
VDI/VDE/DGQ/DKD 2622 Blatt 19:2015-06 | Calibration of measuring equipment for electrical quantities - Characterisation of HF-measuring cables |
VDI/VDE/DGQ/DKD 2622 Blatt 15.4:2010-05 | Calibration of measuring equipment for electrical quantities - Passive measuring equipment for use in EMC-applications - Current clamps |
VDI/VDE 2617 Blatt 12.1:2011-03 | Accuracy of coordinate measuring machines - Characteristics and their checking - Acceptance and reverification tests for tactile CMM measuring microgeometries |
VDI/VDE 2634 Blatt 2:2012-08 | Optical 3-D measuring systems - Optical systems based on area scanning |
VDI/VDE 2629 Blatt 2:2012-06 | Accuracy of contour-measuring systems - Characteristics and their checking - Determination of the uncertainty of specific contour measurements using standards/calibrated workpieces |
VDI/VDE 2617 Blatt 8:2006-07 | Accuracy of coordinate measuring machines - Characteristics and their testing - Test suitability of measurements with coordinate measuring machines |
VDI/VDE 2617 Blatt 9:2009-06 | Accuracy of coordinate measuring machines - Characteristics and their reverification - Acceptance and reverification tests for Articulated Arm Coordinate Measuring Machines |
VDI/VDE 2617 Blatt 13; VDI/VDE 2630 Blatt 1.3:2011-12 | VDI/VDE 2617 Blatt 13: Accuracy of coordinate measuring machines - Characteristics and their testing - Guideline for the application of DIN EN ISO 10360 for coordinate measuring machines with CT-sensors - VDI/VDE 2630 Blatt 1.3: Computed tomography in dimensional measurement - Guideline for the application of DIN EN ISO 10360 for coordinate measuring machines with CT-sensors |
VDI/VDE 2617 Blatt 11:2011-03 | Accuracy of coordinate measuring machines - Characteristics and their checking - Determination of the uncertainty of measurement for coordinate measuring machines using uncertainty budgets |
VDI/VDE/DGQ/DKD 2622 Blatt 21:2004-05 | Calibration of measurement equipments for electrical quantities - Recorders |
VDI/VDE 2630 Blatt 1.2:2010-11 | Computed tomography in dimensional measurement - Influencing variables on measurement results and recommendations for computed tomography dimensional measurements |
VDI/VDE 2630 Blatt 2.1:2015-06 | Computed tomography in dimensional measurement - Determination of the uncertainty of measurement and the test process suitability of coordinate measurement systems with CT sensors |
VDI/VDE/DGQ 2618 Blatt 1.1:2001-12 | Inspection of measuring and test equipment - Instructions to inspect measuring and test equipment for geometrical quantities - Basic principals |
VDI/VDE 2634 Blatt 3:2008-12 | Optical 3D-measuring systems - Multiple view systems based on area scanning |
VDI/VDE 2629 Blatt 1:2008-08 | Accuracy of contour-measuring systems - Characteristics and checking of characteristics - Acceptance testing and reverification testing of contour-measuring systems according to the tactile stylus method |
VDI/VDE/DGQ/DKD 2622 Blatt 1:2014-06 | Calibration of measuring equipment for electrical quantities - Fundamentals |
VDI/VDE 2624 Blatt 2.1:2008-12 | Measurement of mechanical quantities - Instructions for calibration of mobile force measurement systems |
DIN EN ISO 13225:2012-08 | Geometrical product specifications (GPS) - Dimensional measuring equipment; Height gauges - Design and metrological characteristics (ISO 13225:2012) |
DIN EN ISO 12180-2:2011-07 | Geometrical product specifications (GPS) - Cylindricity - Part 2: Specification operators (ISO 12180-2:2011) |
DIN EN ISO 10360-10:2017-03 | Geometrical product specifications (GPS) - Acceptance and reverification tests for coordinate measuring systems (CMS) - Part 10: Laser trackers for measuring point-to-point distances (ISO 10360-10:2016) |
DIN EN ISO 25178-70:2014-06 | GEOMETRICAL PRODUCT SPECIFICATION (GPS) - SURFACE TEXTURE: AREAL - PART 70: MATERIAL MEASURES (ISO 25178-70:2014) |
DIN EN ISO 2538-1:2015-01 | GEOMETRICAL PRODUCT SPECFICATIONS (GPS) - WEDGES - PART 1: SERIES OF ANGLES AND SLOPES; (ISO 2538-1:2014) |
DIN EN ISO 10360-2:2010-06 | Geometrical product specifications (GPS) - Acceptance and reverification tests for coordinate measuring machines (CMM) - Part 2: CMMs used for measuring linear dimensions (ISO 10360-2:2009) |
DIN EN ISO 10360-5:2011-01 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - ACCEPTANCE AND REVERIFICATION TESTS FOR COORDINATE MEASURING MACHINES (CMM) - PART 5: CMMS USING SINGLE AND MULTIPLE STYLUS CONTACTING PROBING SYSTEMS |
DIN EN ISO 2692:2015-12 | Geometrical product specifications (GPS) - Geometrical tolerancing - Maximum material requirement (MMR), least material requirement (LMR) and reciprocity requirement (RPR) (ISO 2692:2014) |
DIN EN ISO 14978:2006-09 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - GENERAL CONCEPTS AND REQUIREMENTS FOR GPS MEASURING EQUIPMENT |
DIN EN ISO 11608-1:2015-04 | Needle-based injection systems for medical use - Requirements and test methods - Part 1: Needle-based injection systems (ISO 11608-1:2014) |
DIN EN ISO 12781-2:2011-07 | Geometrical product specifications (GPS) - Flatness - Part 2: Specification operators (ISO 12781-2:2011) |
DIN EN ISO 14405-3:2013-08 (Draft) | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL TOLERANCING - PART 3: ANGULAR SIZES (ISO 14405-3:2016) |
DIN EN ISO 13102:2012-12 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL MEASURING EQUIPMENT: ELECTRONIC DIGITAL-INDICATOR GAUGE - DESIGN AND METROLOGICAL CHARACTERISTICS (ISO 13102:2012) |
DIN HDBK 11-1 : 4ED 2016 | |
DIN EN ISO 12780-2:2011-07 | Geometrical product specifications (GPS) - Straightness - Part 2: Specification operators (ISO 12780-2:2011) |
DIN EN ISO 14253-3:2011-10 | Geometrical product specifications (GPS) - Inspection by measurement of workpieces and measuring equipment - Part 3: Guidelines for achieving agreements on measurement uncertainty statements (ISO 14253-3:2011) |
DIN EN ISO 16610-71:2014-12 | Geometrical product specifications (GPS) - Filtration - Part 71: Robust areal filters: Gaussian regression filters (ISO 16610-71:2014) |
DIN 16742:2013-10 | PLASTICS MOULDED PARTS - TOLERANCES AND ACCEPTANCE CONDITIONS |
DIN EN ISO 14253-2:2011-11 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - INSPECTION BY MEASUREMENT OF WORKPIECES AND MEASURING EQUIPMENT - PART 2: GUIDANCE FOR THE ESTIMATION OF UNCERTAINTY IN GPS MEASUREMENT, IN CALIBRATION OF MEASURING EQUIPMENT AND IN PRODUCT VERIFICATION (ISO 14253-2:2011) |
DIN EN ISO 3650:1999-02 | Geometrical product specifications (GPS) - Length standards - Gauge blocks (ISO 3650:1998); German version EN ISO 3650:1998 |
DIN EN ISO 5436-1:2000-11 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - SURFACE TEXTURE: PROFILE METHOD - MEASUREMENT STANDARDS - PART 1: MATERIAL MEASURES |
DIN EN ISO 1938-1:2016-03 | Geometrical product specifications (GPS) - Dimensional measuring equipment - Part 1: Plain limit gauges of linear size (ISO 1938-1:2015) |
DIN EN ISO 1938-2:2017-05 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL MEASURING EQUIPMENT - PART 2: REFERENCE DISK GAUGES (ISO 1938-2:2017) |
DIN EN ISO 12181-2:2011-07 | Geometrical product specifications (GPS) - Roundness - Part 2: Specification operators (ISO 12181-2:2011) |
DIN EN ISO 16610-31:2015-09 (Draft) | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - FILTRATION - PART 31: ROBUST PROFILE FILTERS: GAUSSIAN REGRESSION FILTERS (ISO 16610-31:2016) |
DIN EN ISO 13385-2:2013-06 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL MEASURING EQUIPMENT - PART 2: CALLIPER DEPTH GAUGES; DESIGN AND METROLOGICAL CHARACTERISTICS (ISO 13385-2:2011) |
DIN EN ISO 10360-8:2014-03 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - ACCEPTANCE AND REVERIFICATION TESTS FOR COORDINATE MEASURING SYSTEMS (CMS) - PART 8: CMMS WITH OPTICAL DISTANCE SENSORS (ISO 10360-8:2013) |
DIN EN ISO 25178-3:2012-11 | Geometrical product specifications (GPS) - Surface texture: Areal - Part 3: Specification operators (ISO 25178-3:2012); German version EN ISO 25178-3:2012 |
DIN CEN ISO/TS 8062-2;DIN SPEC 91184:2014-03 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL AND GEOMETRICAL TOLERANCES FOR MOULDED PARTS - PART 2: RULES (ISO/TS 8062-2:2013) |
DIN EN ISO 1119:2012-04 | Geometrical product specifications (GPS) - Series of conical tapers and taper angles (ISO 1119:2011) |
DIN EN ISO 10535:2007-04 | Hoists for the transfer of disabled persons - Requirements and test methods (ISO 10535:2006) |
DIN EN ISO 12179:2000-11 | GPS - Surface texture: Profile method - Calibration of contact (stylus) instruments (ISO 12179:2000); English version of DIN EN ISO 12179 |
ISO/TR 14638:1995 | Geometrical product specification (GPS) Masterplan |
ISO 8015:2011 | Geometrical product specifications (GPS) Fundamentals Concepts, principles and rules |
ISO/IEC Guide 99:2007 | International vocabulary of metrology Basic and general concepts and associated terms (VIM) |
ISO 3534-2:2006 | Statistics Vocabulary and symbols Part 2: Applied statistics |
DIN EN ISO 9000:2015-11 | QUALITY MANAGEMENT SYSTEMS - FUNDAMENTALS AND VOCABULARY (ISO 9000:2015) |
ISO 9000:2015 | Quality management systems — Fundamentals and vocabulary |
ISO 14253-2:2011 | Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 2: Guidance for the estimation of uncertainty in GPS measurement, in calibration of measuring equipment and in product verification |
DIN ISO 3534-2:2013-12 | STATISTICS - VOCABULARY AND SYMBOLS - PART 2: APPLIED STATISTICS (ISO 3534-2:2006) |
ISO 25378:2011 | Geometrical product specifications (GPS) Characteristics and conditions Definitions |
ISO/IEC Guide 98-3:2008 | Uncertainty of measurement — Part 3: Guide to the expression of uncertainty in measurement (GUM:1995) |
ISO 3534-1:2006 | Statistics — Vocabulary and symbols — Part 1: General statistical terms and terms used in probability |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.