We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • DIN EN ISO 15874-1:2004-03

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - POLYPROPYLENE (PP)

    Available format(s):  Hardcopy, PDF

    Superseded date:  07-03-2021

    Language(s):  English

    Published date:  01-01-2004

    Publisher:  German Institute for Standardisation (Deutsches Institut für Normung)

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions, symbols and abbreviated terms
      3.1 Terms and definitions
      3.2 Symbols
      3.3 Abbreviated terms
    4 Classification of service conditions
    5 Material
      5.1 General
      5.2 Influence on water intended for human consumption
      5.3 Reprocessable material
    Bibliography

    Abstract - (Show below) - (Hide below)

    Defines the general aspects of polypropylene (PP) piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water whether or not intended for human consumption (domestic systems) and for heating systems, under design pressures and temperatures according to the class of application. Also covers a range of service conditions (classes of application), design pressures and pipe dimension classes.

    General Product Information - (Show below) - (Hide below)

    Development Note Suspended until publication of a revised English text, due to a new German edition. (06/2013)
    Document Type Standard
    Publisher German Institute for Standardisation (Deutsches Institut für Normung)
    Status Superseded
    Superseded By

    Standards Referencing This Book - (Show below) - (Hide below)

    EN 806-1:2000/A1:2001 SPECIFICATIONS FOR INSTALLATIONS INSIDE BUILDINGS CONVEYING WATER FOR HUMAN CONSUMPTION - PART 1: GENERAL
    EN ISO 15874-5:2013 PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - POLYPROPYLENE (PP) - PART 5: FITNESS FOR PURPOSE OF THE SYSTEM (ISO 15874-5:2013)
    ISO 21003-5:2008 Multilayer piping systems for hot and cold water installations inside buildings — Part 5: Fitness for purpose of the system
    ISO 472:2013 Plastics Vocabulary
    ENV 12108 : DRAFT JAN 2001 PLASTICS PIPING SYSTEMS - GUIDANCE FOR THE INSTALLATION INSIDE BUILDINGS OF PRESSURE SYSTEMS FOR HOT AND COLD WATER INTENDED FOR HUMAN CONSUMPTION
    ISO 21003-2:2008 Multilayer piping systems for hot and cold water installations inside buildings — Part 2: Pipes
    ISO 10508:2006 Plastics piping systems for hot and cold water installations Guidance for classification and design
    ISO 21003-1:2008 Multilayer piping systems for hot and cold water installations inside buildings — Part 1: General
    ISO 4065:1996 Thermoplastics pipes Universal wall thickness table
    ISO 21003-3:2008 Multilayer piping systems for hot and cold water installations inside buildings — Part 3: Fittings
    EN ISO 15874-2:2013 PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - POLYPROPYLENE (PP) - PART 2: PIPES (ISO 15874-2:2013)
    ISO/TS 15874-7:2003 Plastics piping systems for hot and cold water installations Polypropylene (PP) Part 7: Guidance for the assessment of conformity
    ISO 1043-1:2011 Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics
    EN ISO 15874-3:2013 PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - POLYPROPYLENE (PP) - PART 3: FITTINGS (ISO 15874-3:2013)
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective