PLASTICS - VOCABULARY (ISO 472:2013)

Available format(s)

Hardcopy , PDF

Published date

01-01-2013

Publisher

German Institute for Standardisation (Deutsches Institut für Normung)

DevelopmentNote	DRAFT AMD 1 issued in September 2016. (09/2016)
DocumentType	Standard
Pages	471
PublisherName	German Institute for Standardisation (Deutsches Institut für Normung)
Status	Current

Standards	Relationship
ISO 472:2013	Identical
EN ISO 472:2013	Identical

DIN EN ISO 22007-6 E : 2015	PLASTICS - DETERMINATION OF THERMAL CONDUCTIVITY AND THERMAL DIFFUSIVITY - PART 6: COMPARATIVE METHOD FOR LOW THERMAL CONDUCTIVITIES USING A TEMPERATURE-MODULATION TECHNIQUE (ISO 22007-6:2014)
DIN EN ISO 16014-5:2012-10	PLASTICS - DETERMINATION OF AVERAGE MOLECULAR MASS AND MOLECULAR MASS DISTRIBUTION OF POLYMERS USING SIZE-EXCLUSION CHROMATOGRAPHY - PART 5: METHOD USING LIGHT-SCATTERING DETECTION (ISO 16014-5:2012)
DIN EN ISO 877-1:2016-09 (Draft)	PLASTICS - METHODS OF EXPOSURE TO SOLAR RADIATION - PART 1: GENERAL GUIDANCE
DIN EN ISO 11357-4 E : 2014	PLASTICS - DIFFERENTIAL SCANNING CALORIMETRY (DSC) - PART 4: DETERMINATION OF SPECIFIC HEAT CAPACITY (ISO 11357-4:2014)
DIN EN ISO 3451-1:2008-11	PLASTICS - DETERMINATION OF ASH - PART 1: GENERAL METHODS
DIN EN ISO 11357-6:2013-04	PLASTICS - DIFFERENTIAL SCANNING CALORIMETRY (DSC) - PART 6: DETERMINATION OF OXIDATION INDUCTION TIME (ISOTHERMAL OIT) AND OXIDATION INDUCTION TEMPERATURE (DYNAMIC OIT) (ISO 11357-6:2008)
DIN 55657:2016-08	Paints and varnishes - Test method for evaluation of elastic adhesives on coatings by peel test, peel strength test and tensile lap-shear strength test with additional stress by condensation test or cataplasm storage
DIN EN ISO 11337:2011-04	Plastics - Polyamides - Determination of -caprolactam and -laurolactam by gas chromatography (ISO 11337:2010)
DIN 16831-2:2003-05	PIPE FITTINGS AND JOINT ASSEMBLIES FOR POLYBUTENE PRESSURE PIPES - TYPE PB 125 - PART 2: DIMENSIONS OF INJECTION-MOULDED TEES FOR SOCKET WELDING
DIN EN ISO 20568-1:2017-10	PLASTICS - FLUOROPOLYMER DISPERSIONS AND MOULDING AND EXTRUSION MATERIALS - PART 1: DESIGNATION SYSTEM AND BASIS FOR SPECIFICATIONS (ISO 20568-1:2017)
DIN EN ISO 9163:2005-07	Textile glass - Rovings - Manufacture of test specimens and determination of tensile strength of impregnated rovings (ISO 9163:2005); German version EN ISO 9163:2005
DIN EN ISO 306:2014-03	Plastics - Thermoplastic materials - Determination of Vicat softening temperature (VST) (ISO 306:2013)
DIN EN ISO 6401:2008-12	Plastics - Poly(vinyl chloride) - Determination of residual vinyl chloride monomer - Gas-chromatographic method (ISO 6401:2008)
DIN EN ISO 1043-3:2017-03	PLASTICS - SYMBOLS AND ABBREVIATED TERMS - PART 3: PLASTICIZERS (ISO 1043-3:2016)
DIN EN ISO 20568-2:2017-10	PLASTICS - FLUOROPOLYMER DISPERSIONS AND MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 20568-2:2017)
DIN EN ISO 11357-6 E : 2013	PLASTICS - DIFFERENTIAL SCANNING CALORIMETRY (DSC) - PART 6: DETERMINATION OF OXIDATION INDUCTION TIME (ISOTHERMAL OIT) AND OXIDATION INDUCTION TEMPERATURE (DYNAMIC OIT) (ISO 11357-6:2008)
DIN EN ISO 10927:2011-07	PLASTICS - DETERMINATION OF THE MOLECULAR MASS AND MOLECULAR MASS DISTRIBUTION OF POLYMER SPECIES BY MATRIX-ASSISTED LASER DESORPTION/IONIZATION TIME-OF-FLIGHT MASS SPECTROMETRY (MALDI-TOF-MS)
DIN EN ISO 11357-7:2015-12	Plastics - Differential scanning calorimetry (DSC) - Part 7: Determination of crystallization kinetics (ISO 11357-7:2015); German version EN ISO 11357-7:2015
DIN EN ISO 25762:2012-04	Plastics - Guidance on the assessment of the fire characteristics and fire performance of fibre-reinforced polymer composites (ISO 25762:2009)
DIN EN ISO 20568-2 E : 2017	PLASTICS - FLUOROPOLYMER DISPERSIONS AND MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 20568-2:2017)
DIN EN ISO 11357-2:2014-07	PLASTICS - DIFFERENTIAL SCANNING CALORIMETRY (DSC) - PART 2: DETERMINATION OF GLASS TRANSITION TEMPERATURE AND GLASS TRANSITION STEP HEIGHT (ISO 11357-2:2013)
DIN EN ISO 16664:2016-07 (Draft)	GAS ANALYSIS - HANDLING OF CALIBRATION GASES AND GAS MIXTURES - GUIDELINES (ISO 16664:2017)
DIN EN ISO 16396-2:2017-07	Plastics - Polyamide (PA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 16396-2:2017)
DIN EN ISO 1874-2:2013-03	PLASTICS - POLYAMIDE (PA) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 1874-2:2012)
DIN EN ISO 15023-1:2016-03 (Draft)	PLASTICS - POLY(VINYL ALCOHOL) (PVAL) MATERIALS - PART 1: DESIGNATION SYSTEM AND BASIS FOR SPECIFICATIONS (ISO 15023-1:2017)
DIN EN ISO 877-1:2011-03	Plastics - Methods of exposure to solar radiation - Part 1: General guidance (ISO 877-1:2009)
DIN EN ISO 22007-6:2015-05	PLASTICS - DETERMINATION OF THERMAL CONDUCTIVITY AND THERMAL DIFFUSIVITY - PART 6: COMPARATIVE METHOD FOR LOW THERMAL CONDUCTIVITIES USING A TEMPERATURE-MODULATION TECHNIQUE (ISO 22007-6:2014)
DIN EN ISO 16396-1:2015-05	Plastics - Polyamide (PA) moulding and extrusion materials - Part 1: Designation system, marking of products and basis for specifications (ISO 16396-1:2015)
DIN EN ISO 11358-1 E : 2014	PLASTICS - THERMOGRAVIMETRY (TG) OF POLYMERS - PART 1: GENERAL PRINCIPLES (ISO 11358-1:2014)
DIN EN ISO 11357-3:2013-04	PLASTICS - DIFFERENTIAL SCANNING CALORIMETRY (DSC) - PART 3: DETERMINATION OF TEMPERATURE AND ENTHALPY OF MELTING AND CRYSTALLIZATION (ISO 11357-3:2011)
DIN EN ISO 306 E : 2014	PLASTICS - THERMOPLASTIC MATERIALS - DETERMINATION OF VICAT SOFTENING TEMPERATURE (VST) (ISO 306:2013)
DIN EN ISO 1452-1:2010-04	Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: General (ISO 1452-1:2009)
DIN EN ISO 1183-1:2013-04	PLASTICS - METHODS FOR DETERMINING THE DENSITY OF NON-CELLULAR PLASTICS - PART 1: IMMERSION METHOD, LIQUID PYKNOMETER METHOD AND TITRATION METHOD (ISO 1183-1:2012)
DIN EN ISO 15877-1:2011-03	Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 1: General (ISO 15877-1:2009 + AMD 1:2010)
DIN EN ISO 9163 E : 2005	TEXTILE GLASS - ROVINGS - MANUFACTURE OF TEST SPECIMENS AND DETERMINATION OF TENSILE STRENGTH OF IMPREGNATED ROVINGS
DIN EN ISO 21003-1:2008-11	MULTILAYER PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS INSIDE BUILDINGS - PART 1: GENERAL
DIN EN ISO 22007-3:2012-04	Plastics - Determination of thermal conductivity and thermal diffusivity - Part 3: Temperature wave analysis method (ISO 22007-3:2008)
DIN EN ISO 11357-4:2014-10	Plastics - Differential scanning calorimetry (DSC) - Part 4: Determination of specific heat capacity (ISO 11357-4:2014)
DIN EN ISO 11357-7 E : 2015	PLASTICS - DIFFERENTIAL SCANNING CALORIMETRY (DSC) - PART 7: DETERMINATION OF CRYSTALLIZATION KINETICS (ISO 113577:2015)
DIN EN ISO 11358-1:2014-10	Plastics - Thermogravimetry (TG) of polymers - Part 1: General principles (ISO 11358-1:2014)
DIN EN ISO 11357-2 E : 2014	PLASTICS - DIFFERENTIAL SCANNING CALORIMETRY (DSC) - PART 2: DETERMINATION OF GLASS TRANSITION TEMPERATURE AND GLASS TRANSITION STEP HEIGHT (ISO 11357-2:2013)
DIN EN ISO 1133-2:2012-03	Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 2: Method for materials sensitive to time-temperature history and/or moisture (ISO 1133-2:2011)
DIN EN ISO 16396-2 E : 2017	PLASTICS - POLYAMIDE (PA) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 16396-2:2017)
DIN EN ISO 6721-1:2011-08	PLASTICS - DETERMINATION OF DYNAMIC MECHANICAL PROPERTIES - PART 1: GENERAL PRINCIPLES
DIN EN ISO 15494:2016-03	PLASTICS PIPING SYSTEMS FOR INDUSTRIAL APPLICATIONS - POLYBUTENE (PB), POLYETHYLENE (PE), POLYETHYLENE OF RAISED TEMPERATURE RESISTANCE (PE-RT), CROSSLINKED POLYETHYLENE (PE-X), POLYPROPYLENE (PP) - METRIC SERIES FOR SPECIFICATIONS FOR COMPONENTS AND THE SYSTEM (ISO 15494:2015)
DIN EN ISO 2078:2016-05	Textile glass - Yarns - Designation (ISO 2078:1993 + Amd 1:2015) (includes Amendment :2015)
DIN EN ISO 1043-1:2016-09	PLASTICS - SYMBOLS AND ABBREVIATED TERMS - PART 1: BASIC POLYMERS AND THEIR SPECIAL CHARACTERISTICS (ISO 1043-1:2011 + AMD.1:2016)
DIN EN ISO 1043-3:2015-09 (Draft)	PLASTICS - SYMBOLS AND ABBREVIATED TERMS - PART 3: PLASTICIZERS (ISO 1043-3:2016)
DIN EN ISO 15750-3:2008-09	Packaging - Steel drums - Part 3: Inserted flange-type closure systems (ISO 15750-3:2002)
DIN 16831-7:2004-02	Pipe fittinings and joint assemblies for polybutene pressure pipes - Type PB 125 - Part 7: Dimensions of bushings, flanges and sealing elements for socket welding
DIN EN ISO 16396-1 E : 2015	PLASTICS - POLYAMIDE (PA) MOULDING AND EXTRUSION MATERIALS - PART 1: DESIGNATION SYSTEM, MARKING OF PRODUCTS AND BASIS FOR SPECIFICATIONS (ISO 16396-1:2015)
DIN EN ISO 20568-1 E : 2017	PLASTICS - FLUOROPOLYMER DISPERSIONS AND MOULDING AND EXTRUSION MATERIALS - PART 1: DESIGNATION SYSTEM AND BASIS FOR SPECIFICATIONS (ISO 20568-1:2017)
DIN EN ISO 11357-3 E : 2013	PLASTICS - DIFFERENTIAL SCANNING CALORIMETRY (DSC) - PART 3: DETERMINATION OF TEMPERATURE AND ENTHALPY OF MELTING AND CRYSTALLIZATION (ISO 11357-3:2011)
DIN EN ISO 20568-1:2015-07 (Draft)	PLASTICS - FLUOROPOLYMER DISPERSIONS AND MOULDING AND EXTRUSION MATERIALS - PART 1: DESIGNATION SYSTEM AND BASIS FOR SPECIFICATIONS (ISO 20568-1:2017)
DIN EN ISO 22391-1:2010-04	Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Part 1: General (ISO 22391-1:2009)
DIN EN ISO 20568-2:2015-07 (Draft)	PLASTICS - FLUOROPOLYMER DISPERSIONS AND MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 20568-2:2017)
DIN 16831-1:2003-05	PIPE FITTINGS AND JOINT ASSEMBLIES FOR POLYBUTENE PRESSURE PIPES - TYPE PB 125 - PART 1: DIMENSIONS OF INJECTION-MOULDED ELBOWS FOR SOCKET WELDING
DIN 16831-4:2003-05	PIPE FITTINGS AND JOINT ASSEMBLIES FOR POLYBUTENE PRESSURE PIPES - TYPE PB 125 - PART 4: DIMENSIONS OF INJECTION-MOULDED REDUCERS FOR SOCKET WELDING
DIN 16831-3:2003-05	PIPE FITTINGS AND JOINT ASSEMBLIES FOR POLYBUTENE PRESSURE PIPES - TYPE PB 125 - PART 3: DIMENSIONS OF INJECTION-MOULDED SOCKETS AND CAPS FOR SOCKET WELDING
DIN 16831-6:2003-06	PIPE FITTINGS AND JOINT ASSEMBLIES FOR POLYBUTENE PRESSURE PIPES - TYPE PB 125 - PART 6: DIMENSIONS OF FITTINGS FOR RESISTANCE WELDING