DIN EN ISO 6185-3:2014-12
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
INFLATABLE BOATS - PART 3: BOATS WITH A HULL LENGTH LESS THAN 8 M WITH A MOTOR POWER RATING OF 15 KW AND GREATER (ISO 6185-3:2014)
Available format(s)
Hardcopy , PDF
Superseded date
03-06-2019
Language(s)
English, German
Published date
01-01-2014
National foreword
National Annex NA (informative) - Bibliography
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols
5 Structural Materials
6 Functional components
7 Safety requirements of the completed boat
8 Performance
9 Builder's plate(s)
10 Owner's manual
11 Standard equipment
Annex A (informative) - General arrangement
of a typical Type VII boat
Annex B (informative) - General arrangement
of a typical Type VIlI boat
Annex ZA (informative) - Relationship between
this European Standard and the Essential
Requirements of EU Directive 94/25/EC
as amended by Directive 2003/44/EC
Bibliography
Defines the minimum safety characteristics required for the design, materials to use, manufacture and testing of inflatable boats and rigid inflatable boats with a hull length L[H] in accordance with ISO 8666 less than 8 m with a motor power rating of 15 kW and greater.
| DocumentType |
Standard
|
| Pages |
44
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| Standards | Relationship |
| NBN EN ISO 6185-3 : 2014 | Identical |
| BS EN ISO 6185-3:2014 | Identical |
| I.S. EN ISO 6185-3:2014 | Identical |
| ISO 6185-3:2014 | Identical |
| NS EN ISO 6185-3 : 2014 | Identical |
| SN EN ISO 6185-3 : 2015 | Identical |
| NEN EN ISO 6185-3 : 2014 | Identical |
| UNE-EN ISO 6185-3:2015 | Identical |
| UNI EN ISO 6185-3 : 2014 | Identical |
| NF EN ISO 6185-3 : 2014 | Identical |
| ONORM EN ISO 6185-3 : 2014 | Identical |
| EN ISO 6185-3:2014 | Identical |
| BWB TL 1940-0012 : 5ED 2007 | |
| DIN EN ISO 6185-4:2011-10 | INFLATABLE BOATS - PART 4: BOATS WITH A HULL LENGTH OF BETWEEN 8 M AND 24 M WITH A MOTOR POWER RATING OF 15 KW AND GREATER |
| ISO 10239:2014 | Small craft Liquefied petroleum gas (LPG) systems |
| ISO 15083:2003 | Small craft - Bilge-pumping systems |
| ISO 12215-5:2008 | Small craft Hull construction and scantlings Part 5: Design pressures for monohulls, design stresses, scantlings determination |
| ISO 2896:2001 | Rigid cellular plastics Determination of water absorption |
| ISO 11192:2005 | Small craft Graphical symbols |
| ISO 7010:2011 | Graphical symbols Safety colours and safety signs Registered safety signs |
| ISO 14946:2001 | Small craft Maximum load capacity |
| DIN EN ISO 6185-4:2011-10 | INFLATABLE BOATS - PART 4: BOATS WITH A HULL LENGTH OF BETWEEN 8 M AND 24 M WITH A MOTOR POWER RATING OF 15 KW AND GREATER |
| DIN ISO 3864-1:2012-06 | Graphical symbols - Safety colours and safety signs - Part 1: Design principles for safety signs and safety markings (ISO 3864-1:2011) |
| DIN EN ISO 2411:2016-07 (Draft) | RUBBER OR PLASTICS-COATED FABRICS - DETERMINATION OF COATING ADHESION (ISO 2411:2017) |
| ISO 4675:2017 | Rubber- or plastics-coated fabrics — Low-temperature bend test |
| DIN EN ISO 15085:2009-10 | SMALL CRAFT - MAN-OVERBOARD PREVENTION AND RECOVERY |
| ISO 12217-3:2015 | Small craft — Stability and buoyancy assessment and categorization — Part 3: Boats of hull length less than 6 m |
| ISO 10088:2013 | Small craft — Permanently installed fuel systems |
| ISO 11547:1994 | Small craft — Start-in-gear protection |
| DIN EN ISO 11105:1997-07 | SMALL CRAFT - VENTILATION OF PETROL ENGINE AND/OR PETROL TANK COMPARTMENTS |
| ISO 6185-4:2011 | Inflatable boats Part 4: Boats with a hull length of between 8 m and 24 m with a motor power rating of 15 kW and greater |
| DIN EN ISO 16180:2013-07 | SMALL CRAFT - NAVIGATION LIGHTS - INSTALLATION, PLACEMENT AND VISIBILITY (ISO 16180:2013) |
| ISO 2411:2017 | Rubber- or plastics-coated fabrics — Determination of coating adhesion |
| ISO 11105:1997 | Small craft Ventilation of petrol engine and/or petrol tank compartments |
| ISO 11592:2001 | Small craft less than 8 m length of hull Determination of maximum propulsion power rating |
| ISO 8666:2016 | Small craft Principal data |
| DIN EN ISO 10592:1995-06 | Small craft - Hydraulic steering systems (ISO 10592:1994) |
| DIN EN ISO 12216:2002-10 | SMALL CRAFT - WINDOWS, PORTLIGHTS, HATCHES, DEADLIGHTS AND DOORS - STRENGTH AND WATERTIGHTNESS REQUIREMENTS |
| DIN ISO 1817:2016-11 | RUBBER, VULCANIZED OR THERMOPLASTIC - DETERMINATION OF THE EFFECT OF LIQUIDS (ISO 1817:2015) |
| DIN EN ISO 21487:2016-05 | SMALL CRAFT - PERMANENTLY INSTALLED PETROL AND DIESEL FUEL TANKS (ISO 21487:2012 + AMD 1:2014 + AMD 2:2015) |
| ISO 8847:2004 | Small craft Steering gear Cable and pulley systems |
| DIN EN ISO 10240:2015-09 | SMALL CRAFT - OWNER'S MANUAL (ISO 10240:2004 + AMD 1:2015) |
| ISO 15084:2003 | Small craft Anchoring, mooring and towing Strong points |
| ISO 9775:1990 | Small craft Remote steering systems for single outboard motors of 15 kW to 40 kW power |
| ISO 10133:2012 | Small craft Electrical systems Extra-low-voltage d.c. installations |
| ISO 8469:2013 | Small craft Non-fire-resistant fuel hoses |
| ISO 12217-1:2015 | Small craft — Stability and buoyancy assessment and categorization — Part 1: Non-sailing boats of hull length greater than or equal to 6 m |
| ISO 12215-3:2002 | Small craft — Hull construction and scantlings — Part 3: Materials: Steel, aluminium alloys, wood, other materials |
| DIN EN ISO 10088:2013-12 | Small craft - Permanently installed fuel systems (ISO 10088:2013) |
| DIN EN ISO 11812:2003-07 | SMALL CRAFT - WATERTIGHT COCKPITS AND QUICK-DRAINING COCKPITS |
| ISO 8846:1990 | Small craft — Electrical devices — Protection against ignition of surrounding flammable gases |
| ISO 8849:2003 | Small craft Electrically operated direct-current bilge pumps |
| ISO 8848:1990 | Small craft Remote steering systems |
| DIN EN ISO 10239:2015-05 | SMALL CRAFT - LIQUEFIED PETROLEUM GAS (LPG) SYSTEMS (ISO 10239:2014) |
| ISO 16180:2013 | Small craft — Navigation lights — Installation, placement and visibility |
| ISO 10592:1994 | Small craft Hydraulic steering systems |
| ISO 15652:2003 | Small craft Remote steering systems for inboard mini jet boats |
| ISO 11812:2001 | Small craft Watertight cockpits and quick-draining cockpits |
| DIN EN ISO 8099:2015-11 (Draft) | SMALL CRAFT - TOILET WASTE RETENTION SYSTEMS |
| ISO 12215-1:2000 | Small craft — Hull construction and scantlings — Part 1: Materials: Thermosetting resins, glass-fibre reinforcement, reference laminate |
| ISO 10240:2004 | Small craft Owner's manual |
| ISO 21487:2012 | Small craft — Permanently installed petrol and diesel fuel tanks |
| ISO 3864-1:2011 | Graphical symbols Safety colours and safety signs Part 1: Design principles for safety signs and safety markings |
| ISO 13297:2014 | Small craft Electrical systems Alternating current installations |
| ISO 15085:2003 | Small craft Man-overboard prevention and recovery |
| ISO 9094:2015 | Small craft — Fire protection |
| EN 314-2:1993 | Plywood - Bonding quality - Part 2: Requirements |
| DIN EN ISO 9094:2016-05 | Small craft - Fire protection (ISO 9094:2015) |
| DIN EN 29775:1993-10 | Small craft; remote steering systems for single outboard motors of 15 kW to 40 kW (ISO 9975:1990); German version EN 29975:1993 |
| ISO 16147:2002 | Small craft Inboard diesel engines Engine-mounted fuel and electrical components |
| ISO 15584:2001 | Small craft Inboard petrol engines Engine-mounted fuel and electrical components |
| DIN EN ISO 4674-1:2015-04 (Draft) | RUBBER- OR PLASTICS-COATED FABRICS - DETERMINATION OF TEAR RESISTANCE - PART 1: CONSTANT RATE OF TEAR METHODS (ISO 4674-1:2016) |
| DIN EN ISO 8666:2014-12 (Draft) | SMALL CRAFT - PRINCIPAL DATA (ISO 8666:2016) |
| ISO 8665:2006 | Small craft Marine propulsion reciprocating internal combustion engines Power measurements and declarations |
| ISO 12216:2002 | Small craft Windows, portlights, hatches, deadlights and doors Strength and watertightness requirements |
| DIN EN ISO 12217-3:2016-03 | SMALL CRAFT - STABILITY AND BUOYANCY ASSESSMENT AND CATEGORIZATION - PART 3: BOATS OF HULL LENGTH LESS THAN 6 M (ISO 12217-3:2015) |
| DIN EN ISO 7010:2012-10 | GRAPHISCHE SYMBOLE - SICHERHEITSFARBEN UND SICHERHEITSZEICHEN - REGISTRIERTE SICHERHEITSZEICHEN (ISO 7010:2011/AMD 5:2014) |
| DIN EN ISO 13297:2015-04 | SMALL CRAFT - ELECTRICAL SYSTEMS - ALTERNATING CURRENT INSTALLATIONS (ISO 13297:2014) |
| ISO 3011:1997 | Rubber- or plastics-coated fabrics Determination of resistance to ozone cracking under static conditions |
| DIN EN ISO 10133:2013-04 | Small craft - Electrical systems - Extra-low-voltage d.c. installations (ISO 10133:2012) |
| ISO 4674-1:2016 | Rubber- or plastics-coated fabrics Determination of tear resistance Part 1: Constant rate of tear methods |
| ISO 10087:2006 | Small craft Craft identification Coding system |
| ISO 12215-6:2008 | Small craft — Hull construction and scantlings — Part 6: Structural arrangements and details |
| DIN EN ISO 12215-3:2002-09 | SMALL CRAFT - HULL CONSTRUCTION AND SCANTLINGS - PART 3: MATERIALS: STEEL, ALUMINIUM ALLOYS, WOOD, OTHER MATERIALS |
| ISO 1817:2015 | Rubber, vulcanized or thermoplastic Determination of the effect of liquids |
| ISO 14945:2004 | Small craft Builder's plate |
| ISO 8099:2000 | Small craft Toilet waste retention systems |
| DIN EN ISO 12217-1:2016-08 | SMALL CRAFT - STABILITY AND BUOYANCY ASSESSMENT AND CATEGORIZATION - PART 1: NON-SAILING BOATS OF HULL LENGTH GREATER THAN OR EQUAL TO 6 M (ISO 12217-1:2015) |
$270.84
Including GST where applicable
AUD
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - English
PDF - English
Hardcopy - German
PDF - German
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.