DIN ISO 669:2001-06
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
RESISTANCE WELDING - RESISTANCE WELDING EQUIPMENT - MECHANICAL AND ELECTRICAL REQUIREMENTS
Superseded date
01-07-2016
Published date
12-01-2013
Vorwort
1 Anwendungsbereich
2 Normative Verweisungen
3 Begriffe und Definitionen
4 Symbole
5 Einteilung
6 Physikalische Umgebung und Betriebsbedingungen
7 Prüfbedingungen
8 Schweisstransformatoren
9 Bemessungswert der Leerlaufspannung am Ausgang
10 Grösster Kurzschlussstrom
11 Thermische Bemessung
12 Erwärmungsprüfung
13 Bedingungen zum Messen der Erwärmung
14 Kühlflüssigkeitskreis (flüssigkeitsgekühlte
Schweisseinrichtung)
15 Statische, mechanische Kenngrössen
16 Leistungsschild
17 Betriebsanleitung
Anhang A (normativ) Dynamisches, mechanisches Verhalten
Anhang B (informativ) Beispiele für Leistungsschilder
This standard is included in DIN DVS Handbook 312/3. Sets out properties of single-phase machines, among them all kinds of complete portable apparatus. Provides details for nameplate. Also deals with testing.
| DevelopmentNote |
Supersedes DIN ISO 669-1. (06/2001)
|
| DocumentType |
Standard
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| ISO 669:2016 | Identical |
| DIN EN ISO 15614-12:2014-10 | Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 12: Spot, seam and projection welding (ISO 15614-12:2014); German version EN ISO 15614-12:2014 |
| DIN EN ISO 17657-4:2007-09 | RESISTANCE WELDING - WELDING CURRENT MEASUREMENT FOR RESISTANCE WELDING - PART 4: CALIBRATION SYSTEM |
| DIN EN ISO 17657-2 E : 2007 | RESISTANCE WELDING - WELDING CURRENT MEASUREMENT FOR RESISTANCE WELDING - PART 2: WELDING CURRENT METER WITH CURRENT SENSING COIL |
| DIN EN ISO 17657-5 E : 2007 | RESISTANCE WELDING - WELDING CURRENT MEASUREMENT FOR RESISTANCE WELDING - PART 5: VERIFICATION OF WELDING CURRENT MEASURING SYSTEM |
| DIN EN ISO 17657-2:2007-09 | Resistance welding - Welding current measurement for resistance welding - Part 2: Welding current meter with current sensing coil (ISO 17657-2:2005) |
| DIN EN ISO 17657-3:2007-09 | RESISTANCE WELDING - WELDING CURRENT MEASUREMENT FOR RESISTANCE WELDING - PART 3: CURRENT SENSING COIL |
| DIN DVS HDBK 312/3 : 3ED 2010 | |
| DIN EN ISO 15609-5:2012-03 | Specification and qualification of welding procedures for metallic materials - Welding procedure specification - Part 5: Resistance welding (ISO 15609-5:2011) |
| DIN EN ISO 14554-1:2014-05 | Quality requirements for welding - Resistance welding of metallic materials - Part 1: Comprehensive quality requirements (ISO 14554-1:2013) |
| DIN EN ISO 17657-3 E : 2007 | RESISTANCE WELDING - WELDING CURRENT MEASUREMENT FOR RESISTANCE WELDING - PART 3: CURRENT SENSING COIL |
| DIN EN ISO 17657-4 E : 2007 | RESISTANCE WELDING - WELDING CURRENT MEASUREMENT FOR RESISTANCE WELDING - PART 4: CALIBRATION SYSTEM |
| DIN EN ISO 14373:2015-06 | Resistance welding - Procedure for spot welding of uncoated and coated low carbon steels (ISO 14373:2015) |
| DIN EN ISO 17657-5:2007-09 | RESISTANCE WELDING - WELDING CURRENT MEASUREMENT FOR RESISTANCE WELDING - PART 5: VERIFICATION OF WELDING CURRENT MEASURING SYSTEM |
| DIN EN ISO 16432:2007-09 | Resistance welding - Procedure for projection welding of uncoated and coated low carbon steels using embossed projection(s) (ISO 16432:2006) |
| DIN EN ISO 16433:2007-09 | Resistance welding - Procedure for seam welding of uncoated and coated low carbon steels (ISO 16433:2006) |
| DIN EN ISO 5826:2014-07 | RESISTANCE WELDING EQUIPMENT - TRANSFORMERS - GENERAL SPECIFICATIONS APPLICABLE TO ALL TRANSFORMERS (ISO 5826:2014) |
| DIN EN ISO 17657-1 E : 2007 | RESISTANCE WELDING - WELDING CURRENT MEASUREMENT FOR RESISTANCE WELDING - PART 1: GUIDELINES FOR MEASUREMENT |
| DIN EN ISO 17657-1:2007-09 | RESISTANCE WELDING - WELDING CURRENT MEASUREMENT FOR RESISTANCE WELDING - PART 1: GUIDELINES FOR MEASUREMENT |
| DIN ISO 12166 E : 2006 | RESISTANCE WELDING EQUIPMENT - PARTICULAR SPECIFICATIONS APPLICABLE TO TRANSFORMERS WITH ONE SECONDARY WINDING FOR MULTISPOT WELDING, AS USED IN THE AUTOMOBILE INDUSTRY |
| DIN EN ISO 18595:2007-12 | Resistance welding - Spot welding of aluminium and aluminium alloys - Weldability, welding and testing (ISO 18595:2007); German version EN ISO 18595:2007 |
| DIN ISO 12166:2006-02 | RESISTANCE WELDING EQUIPMENT - PARTICULAR SPECIFICATIONS APPLICABLE TO TRANSFORMERS WITH ONE SECONDARY WINDING FOR MULTISPOT WELDING, AS USED IN THE AUTOMOBILE INDUSTRY |
| DIN ISO 5826 : 2000 | RESISTANCE WELDING EQUIPMENT - TRANSFORMERS - GENERAL SPECIFICATIONS APPLICABLE TO ALL TRANSFORMERS |
| DIN EN 25183-2:1992-02 | RESISTANCE SPOT WELDING - ELECTRODE ADAPTORS, MALE TAPER 1:10 - PART 2: PARALLEL SHANK FIXING FOR END-THRUST ELECTRODES |
| EN 20865:1991 | Slots in plates for projection welding machines (ISO 865:1981) |
| DIN EN ISO 5183-1:2000-07 | Resistance welding equipment - Electrode adaptors, male taper 1:10 - Part 1: Conical fixing, taper 1:10 (ISO 5183-1:1998); German version EN ISO 5183-1:2000 |
| EN 28430-1:1992 | Resistance spot welding - Electrode holders - Part 1: Taper fixing 1:10 (ISO 8430-1:1988) |
| ISO 865:1981 | Slots in platens for projection welding machines |
| ISO 5830:1984 | Resistance spot welding Male electrode caps |
| IEC 60204-1:2016 | Safety of machinery - Electrical equipment of machines - Part 1: General requirements |
| ISO 5829:1984 | Resistance spot welding Electrode adaptors, female taper 1 : 10 |
| DIN ISO 5821:1984-04 | RESISTANCE SPOT WELDING ELECTRODE CAPS |
| DIN EN 28430-2:1992-07 | RESISTANCE SPOT WELDING; ELECTRODE HOLDERS; PART 2: MORSE TAPER FIXING |
| DIN EN 60204-1 : 2010 | SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS |
| DIN ISO 5184:1984-04 | STRAIGHT RESISTANCE SPOT WELDING ELECTRODES |
| IEC 60051-2:1984 | Direct acting indicating analogue electrical measuring instruments and their accessories. Part 2: Special requirements for ammeters and voltmeters |
| DIN EN 28430-1:1992-07 | RESISTANCE SPOT WELDING; ELECTRODE HOLDERS; PART 1: TAPER FIXING 1:10 |
| DIN EN 60051-2:1991-11 | Direct acting indicating analogue electrical measuring instruments and their accessories; part 2: special requirements for ammeters and voltmeters (IEC 60051-2:1984, edition 4); german version EN 60051-2:1989 |
| EN ISO 5183-1:2000 | Resistance welding equipment - Electrode adaptors, male taper 1:10 - Part 1: Conical fixing, taper 1:10 (ISO 5183-1:1998) |
| ISO 8430-1:2016 | Resistance spot welding Electrode holders Part 1: Taper fixing 1:10 |
| ISO 8430-2:2016 | Resistance spot welding Electrode holders Part 2: Morse taper fixing |
| DIN EN 28430-3:1992-07 | RESISTANCE SPOT WELDING; ELECTRODE HOLDERS; PART 3: PARALLEL SHANK FIXING FOR END THRUST |
| EN 28430-2:1992 | Resistance spot welding - Electrode holders - Part 2: Morse taper fixing (ISO 8430-2:1988) |
| VDE 0113-1 : 2007 COR 1 2010 | SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS |
| ISO 8430-3:2016 | Resistance spot welding Electrode holders Part 3: Parallel shank fixing for end thrust |
| EN 28430-3:1992 | Resistance spot welding - Electrode holders - Part 3: Parallel shank fixing for end thrust (ISO 8430-3:1988) |
| ISO 5183-1:1998 | Resistance welding equipment Electrode adaptors, male taper 1:10 Part 1: Conical fixing, taper 1:10 |
| EN 60051-2:1989 | Direct acting indicating analogue electrical measuring instruments and their accessories - Part 2: Special requirements for ammeters and voltmeters |
| EN 25183-2 : 1991 | RESISTANCE SPOT WELDING - ELECTRODE ADAPTORS, MALE TAPER 1:10 - PARALLEL SHANK FIXING FOR END-THRUST ELECTRODES |
| DIN EN 20865:1992-02 | SLOTS IN PLATENS FOR PROJECTION WELDING MACHINES |
| ISO 5184:1979 | Straight resistance spot welding electrodes |
| ISO 5826:2014 | Resistance welding equipment Transformers General specifications applicable to all transformers |
| ISO 5183-2:2000 | Resistance spot welding Electrode adaptors, male taper 1:10 Part 2: Parallel shank fixing for end-thrust electrodes |
| EN 60204-1 : 2006 COR 2010 | SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS |
| ISO 5821:2009 | Resistance welding — Spot welding electrode caps |
Sorry this product is not available in your region.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.