EN 12082:2017
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Railway applications - Axleboxes - Performance testing
Superseded date
02-07-2021
Published date
06-09-2017
Publisher
European foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviations
5 Test specification
6 Water tightness test
7 Rig performance test
8 Field test
Annex A (normative) - Rig performance test
Annex B (informative) - Sequenced performance tests
Annex C (normative) - Water tightness test
Annex ZA (informative) - Relationship between this
European Standard and the Essential
Requirements of EU Directive 2008/57/EC
aimed to be covered
Bibliography
This European Standard specifies the principles and methods for a rig performance test of the system of axlebox rolling bearing(s), housing, seal(s) and grease. Test parameters and minimum performance requirements for vehicles in operation on main lines are specified. Different test parameters and performance requirements may be selected for vehicles in operation on other networks (e.g. urban rail). This standard is historically developed for outboard applications but can be used for vehicles with other bearing arrangements (e.g.: inboard application or single wheels).It gives some possible examples where a "sequenced performance test" addresses the broad range of different service conditions within a specific application or vehicle platform into account.It describes in detail the water tightness test and basic principles and minimum requirements for a field test.This European Standard only applies to axleboxes equipped with rolling bearings and greases according to EN 12080 and EN 12081.
| Committee |
CEN/TC 256
|
| DevelopmentNote |
Supersedes PREN 12082. (09/2017)
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| UNI EN 12082:2017 | Identical |
| UNE-EN 12082:2008 | Identical |
| UNE-EN 12082:2018 | Identical |
| DIN EN 12082:2011-01 | Identical |
| DIN EN 12082:2015-06 (Draft) | Identical |
| UNI EN 12082 : 2011 | Identical |
| I.S. EN 12082:2017 | Identical |
| NEN EN 12082 : 2017 | Identical |
| NBN EN 12082 : 2008 + A1 2010 | Identical |
| BS EN 12082:2017 | Identical |
| NS EN 12082 : 2017 | Identical |
| SN EN 12082 : 2017 | Identical |
| PN EN 12082 : 2017 | Identical |
| NF EN 12082 : 2017 | Identical |
| ONORM EN 12082 : 2017 | Identical |
| DIN EN 15313:2016-09 | RAILWAY APPLICATIONS - IN-SERVICE WHEELSET OPERATION REQUIREMENTS - IN-SERVICE AND OFF-VEHICLE WHEELSET MAINTENANCE |
| UNE-EN 14865-1:2010 | Railway Applications - Axlebox lubricating greases - Part 1: Method to test the ability to lubricate |
| UNI EN 13749 : 2011 | RAILWAY APPLICATIONS - WHEELSETS AND BOGIES - METHODS OF SPECIFYING THE STRUCTURAL REQUIREMENTS OF BOGIES FRAMES |
| 07/30159027 DC : 0 | BS EN 14865-1 - RAILWAY APPLICATIONS - AXLEBOX LUBRICATING GREASES - PART 1: METHOD TO TEST THE ABILITY TO LUBRICATE ORDINARY-SPEED VEHICLES WITH SPEEDS UP TO 200 KM/H AND HIGH-SPEED VEHICLES WITH SPEEDS UP TO 300 KM/H |
| 05/30143127 DC : 0 | EN 15437 - RAILWAY APPLICATIONS - HOT BOX DETECTORS - PERFORMANCE REQUIREMENTS |
| I.S. EN 15827:2011 | RAILWAY APPLICATIONS - REQUIREMENTS FOR BOGIES AND RUNNING GEARS |
| DIN EN 15827:2011-06 | Railway applications - Requirements for bogies and running gears |
| NF EN 15827 : 2011 | RAILWAY APPLICATIONS - REQUIREMENTS FOR BOGIES AND RUNNING GEARS |
| UNE-EN 15313:2017 | Railway applications - In-service wheelset operation requirements - In-service and off-vehicle wheelset maintenance |
| EN 12080:2017 | Railway applications - Axleboxes - Rolling bearings |
| EN 12081:2017 | Railway applications - Axleboxes - Lubricating greases |
| I.S. EN 14865-2:2006 | RAILWAY APPLICATIONS - AXLEBOX LUBRICATING GREASES - PART 2: METHOD TO TEST THE MECHANICAL STABILITY TO COVER VEHICLE SPEEDS UP TO 200 KM/H |
| 05/30137050 DC : 0 | EN 15313 - RAILWAY APPLICATIONS - WHEELSETS AND BOGIES - WHEELSET MAINTENANCE |
| I.S. EN 15313:2016 | RAILWAY APPLICATIONS - IN-SERVICE WHEELSET OPERATION REQUIREMENTS IN-SERVICE AND OFF-VEHICLE WHEELSET MAINTENANCE |
| BS EN 15437-1:2009 | Railway applications. Axlebox condition monitoring. Interface and design requirements Track side equipment and rolling stock axlebox |
| UNI EN 15437-2 : 2012 | RAILWAY APPLICATIONS - AXLEBOX CONDITION MONITORING - INTERFACE AND DESIGN REQUIREMENTS - PART 2: PERFORMANCE AND DESIGN REQUIREMENTS OF ON-BOARD SYSTEMS FOR TEMPERATURE MONITORING |
| I.S. EN 13749:2011 | RAILWAY APPLICATIONS - WHEELSETS AND BOGIES - METHOD OF SPECIFYING THE STRUCTURAL REQUIREMENTS OF BOGIE FRAMES |
| 11/30239989 DC : 0 | BS EN 16251 - RAILWAY APPLICATION - ENVIRONMENTAL CONDITIONS - DESIGN AND TEST OF ROLLING STOCK UNDER SEVERE CONDITIONS |
| BS EN 13749:2011 | Railway applications. Wheelsets and bogies. Method of specifying the structural requirements of bogie frames |
| DIN EN 12081:2015-06 (Draft) | RAILWAY APPLICATIONS - AXLEBOXES - LUBRICATING GREASES |
| DIN EN 12080:2015-06 (Draft) | RAILWAY APPLICATIONS - AXLEBOXES - ROLLING BEARINGS |
| BS EN 12081:2017 | Railway applications - Axleboxes - Lubricating greases |
| BS EN 12080:2017 | Railway applications. Axleboxes. Rolling bearings |
| I.S. EN 12081:2017 | RAILWAY APPLICATIONS - AXLEBOXES - LUBRICATING GREASES |
| I.S. EN 12080:2017 | RAILWAY APPLICATIONS - AXLEBOXES - ROLLING BEARINGS |
| DIN EN 12080:2017-11 | Railway applications - Axleboxes - Rolling bearings |
| DIN EN 15313 E : 2016 | RAILWAY APPLICATIONS - IN-SERVICE WHEELSET OPERATION REQUIREMENTS - IN-SERVICE AND OFF-VEHICLE WHEELSET MAINTENANCE |
| UNE-EN 15437-2:2013 | Railway applications - Axlebox condition monitoring - Interface and design requirements - Part 2: Performance and design requirements of on-board systems for temperature monitoring |
| BS EN 15827:2011 | Railway applications. Requirements for bogies and running gears |
| 13/30279798 DC : 0 | BS EN 15313 - RAILWAY APPLICATIONS - IN-SERVICE WHEELSET OPERATION REQUIREMENTS - IN-SERVICE AND OFF-VEHICLE WHEELSET MAINTENANCE |
| 08/30174483 DC : DRAFT JULY 2008 | BS EN 15827-2 - RAILWAY APPLICATIONS - BOGIES AND RUNNING GEAR - PART 2: STRUCTURAL REQUIREMENTS |
| 03/321614 DC : DRAFT DEC 2003 | PREN 14865-2 - RAILWAY APPLICATIONS - AXLEBOX LUBRICATING GREASES - PART 2: METHOD TO TEST THE MECHANICAL STABILITY TO COVER VEHICLE SPEEDS UP TO 200 KM/H |
| BS EN 14865-1 : 2009 | RAILWAY APPLICATIONS - AXLEBOX LUBRICATING GREASES - PART 1: METHOD TO TEST THE ABILITY TO LUBRICATE |
| 15/30309997 DC : 0 | BS EN 15663 - RAILWAY APPLICATIONS - VEHICLE REFERENCE MASSES |
| PREN 17069-1 : DRAFT 2017 | RAILWAY APPLICATIONS - SYSTEMS AND PROCEDURES FOR CHANGE OF TRACK GAUGE - PART 1: AUTOMATIC VARIABLE GAUGE SYSTEMS |
| I.S. EN 15437-2:2012 | RAILWAY APPLICATIONS - AXLEBOX CONDITION MONITORING - INTERFACE AND DESIGN REQUIREMENTS - PART 2: PERFORMANCE AND DESIGN REQUIREMENTS OF ON-BOARD SYSTEMS FOR TEMPERATURE MONITORING |
| I.S. EN 14865-1:2009 | RAILWAY APPLICATIONS - AXLEBOX LUBRICATING GREASES - PART 1: METHOD TO TEST THE ABILITY TO LUBRICATE |
| UNE-EN 13749:2012 | Railway applications - Wheelsets and bogies - Method of specifying the structural requirements of bogie frames |
| UNI EN 14865-2 : 2011 | RAILWAY APPLICATIONS - AXLEBOX LUBRICATING GREASES - PART 2: METHOD TO TEST THE MECHANICAL STABILITY TO COVER VEHICLE SPEEDS UP TO 200 KM/H |
| UNI EN 15827 : 2011 | RAILWAY APPLICATIONS - REQUIREMENTS FOR BOGIES AND RUNNING GEARS |
| DIN EN 15437-2:2012-12 | Railway applications - Axlebox condition monitoring - Interface and design requirements - Part 2: Performance and design requirements of on-board systems for temperature monitoring |
| UNI EN 15437-1 : 2009 | RAILWAY APPLICATIONS - AXLEBOX CONDITION MONITORING - INTERFACE AND DESIGN REQUIREMENTS - PART 1: TRACK SIDE EQUIPMENT AND ROLLING STOCK AXLEBOX |
| DIN EN 13749:2011-06 | Railway applications - Wheelsets and bogies - Method of specifying the structural requirements of bogie frames |
| I.S. EN 15437-1:2009 | RAILWAY APPLICATIONS - AXLEBOX CONDITION MONITORING - INTERFACE AND DESIGN REQUIREMENTS - PART 1: TRACK SIDE EQUIPMENT AND ROLLING STOCK AXLEBOX |
| UNI EN 14865-1 : 2011 | RAILWAY APPLICATIONS - AXLEBOX LUBRICATING GREASES - PART 1: METHOD TO TEST THE ABILITY TO LUBRICATE |
| 08/30180826 DC : DRAFT JULY 2008 | BS EN 13749 - RAILWAY APPLICATIONS - WHEELSETS AND BOGIES - METHOD OF SPECIFYING THE STRUCTURAL REQUIREMENTS OF BOGIE FRAMES |
| DIN EN 15437-1:2010-06 | Railway applications - Axlebox condition monitoring - Interface and design requirements - Part 1: Track side equipment and rolling stock axlebox |
| UNE-EN 15437-1:2010 | Railway applications - Axlebox condition monitoring - Interface and design requirements - Part 1: Track side equipment and rolling stock axlebox |
| DIN EN 14865-2:2011-01 | Railway applications - Axlebox lubricating greases - Part 2: Method to test the mechanical stability to cover vehicle speeds up to 200 km/h (includes Amendment A2:2010) |
| UNE-EN 15827:2011 | Railway applications - Requirements for bogies and running gears |
| EN 14865-1:2009+A1:2010 | Railway applications - Axlebox lubricating greases - Part 1: Method to test the ability to lubricate |
| EN 15437-1:2009 | Railway applications - Axlebox condition monitoring - Interface and design requirements - Part 1: Track side equipment and rolling stock axlebox |
| EN 15313:2016 | Railway applications - In-service wheelset operation requirements - In-service and off-vehicle wheelset maintenance |
| EN 15827:2011 | Railway applications - Requirements for bogies and running gears |
| EN 15437-2:2012 | Railway applications - Axlebox condition monitoring - Interface and design requirements - Part 2: Performance and design requirements of on-board systems for temperature monitoring |
| EN 14865-2:2006+A2:2010 | Railway applications - Axlebox lubricating greases - Part 2: Method to test the mechanical stability to cover vehicle speeds up to 200 km/h |
| 17/30279844 DC : 0 | BS EN 17069-1 - RAILWAY APPLICATIONS - SYSTEMS AND PROCEDURES FOR CHANGE OF TRACK GAUGE - PART 1: AUTOMATIC VARIABLE GAUGE SYSTEMS |
| DIN EN 14865-1:2011-01 | Railway applications - Axlebox lubricating greases - Part 1: Method to test the ability to lubricate (includes Amendment A1:2010) |
| BS EN 15437-2:2012 | Railway applications. Axlebox condition monitoring. Interface and design requirements Performance and design requirements of on-board systems for temperature monitoring |
| 99/716338 DC : DRAFT NOV 1999 | PREN 13749 - RAILWAY APPLICATIONS - WHEELSETS AND BOGIES - METHOD OF SPECIFYING STRUCTURAL REQUIREMENTS OF BOGIE FRAMES |
| 08/30174486 DC : DRAFT JULY 2008 | BS EN 15827-3 - RAILWAY APPLICATIONS - BOGIES AND RUNNING GEAR - PART 3: DYNAMIC REQUIREMENTS |
| BS EN 14865-2 : 2006 | RAILWAY APPLICATIONS - AXLEBOX LUBRICATING GREASES - PART 2: METHOD TO TEST THE MECHANICAL STABILITY TO COVER VEHICLE SPEEDS UP TO 200 KM/H |
| EN 13749:2011 | Railway applications - Wheelsets and bogies - Method of specifying the structural requirements of bogie frames |
| EN 15437-1:2009 | Railway applications - Axlebox condition monitoring - Interface and design requirements - Part 1: Track side equipment and rolling stock axlebox |
| ISO/IEC 17025:2005 | General requirements for the competence of testing and calibration laboratories |
| DIN 51829:2013-03 | PETROLEUM PRODUCTS - DETERMINATION OF ADDITIVE AND WEAR ELEMENTS IN GREASES - ANALYSIS BY WAVELENGTH DISPERSIVE X-RAY FLUORESCENCE SPECTROMETRY |
| EN ISO 11885:2009 | Water quality - Determination of selected elements by inductively coupled plasma optical emission spectrometry (ICP-OES) (ISO 11885:2007) |
| EN 12080:2017 | Railway applications - Axleboxes - Rolling bearings |
| EN 12081:2017 | Railway applications - Axleboxes - Lubricating greases |
| ISO 11885:2007 | Water quality Determination of selected elements by inductively coupled plasma optical emission spectrometry (ICP-OES) |
| ASTM D 7303 : 2017 : REDLINE | Standard Test Method for Determination of Metals in Lubricating Greases by Inductively Coupled Plasma Atomic Emission Spectrometry |
| EN 15663:2017 | Railway applications - Vehicle reference masses |
| DIN 51460-1:2007-11 | TESTING OF PETROLEUM PRODUCTS - METHOD FOR SAMPLE PREPARATION - PART 1: MICROWAVE INCINERATION |
| ISO 15243:2017 | Rolling bearings — Damage and failures — Terms, characteristics and causes |
Sorry this product is not available in your region.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.