Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

EN 13274-7:2008

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Respiratory protective devices - Methods of test - Part 7: Determination of particle filter penetration
Superseded date

26-06-2019

Published date

23-01-2008

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Pre-requisites
5 Test requirements
  5.1 General
  5.2 Penetration test
  5.3 Exposure test
  5.4 Storage test
6 Sodium chloride test method
  6.1 Principle
  6.2 Test equipment
  6.3 Test conditions
  6.4 Procedure
  6.5 Calculation of the penetration
7 Paraffin oil test method
  7.1 Principle
  7.2 Test equipment
  7.3 Test conditions at filter
  7.4 Procedure
  7.5 Calculation of the penetration
Annex A (normative) Test results - Uncertainty of measurements
Annex ZA (informative) Relationship between this European
                       Standard and the Essential Requirements
                       of EU Directives

This European Standard specifies the procedure for testing particle filter penetration for respiratory protective devices.

Committee
CEN/TC 79
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Superseded
SupersededBy

DIN EN 16913 E : 2017 AMBIENT AIR - STANDARD METHOD FOR MEASUREMENT OF NO[3][-], SO[4][2-], CL[-], NH[4][+], NA[+], K[+], MG[2+], CA[2+] IN PM2,5 AS DEPOSITED ON FILTERS
12/30268424 DC : 0 BS EN 12341 - AMBIENT AIR - STANDARD GRAVIMETRIC MEASUREMENT METHOD FOR THE DETERMINATION OF THE PM10 OR PM2,5 MASS CONCENTRATION OF SUSPENDED PARTICULATE MATTER
07/30163576 DC : 0 BS EN 14387 AMD 1 - RESPIRATORY PROTECTIVE DEVICES - GAS FILTER(S) AND COMBINED FILTER(S) - REQUIREMENTS, TESTING, MARKING
PD CEN/TR 16269:2011 Ambient air. Guide for the measurement of anions and cations in PM2,5
UNE-EN 1827:1999 RESPIRATORY PROTECTIVE DEVICES. HALF MASKS WITHOUT INHALATION VALVES AND WITH SEPARABLE FILTERS TO PROTECT AGAINST GASES OR GASES AND PARTICLES OR PARTICLES ONLY. REQUIREMENTS, TESTING, MARKING
BS EN 12341:2014 Ambient air. Standard gravimetric measurement method for the determination of the PM<sub>10</sub> or PM<sub>2</sub>$d,<sub>5</sub> mass concentration of suspended particulate matter
DIN EN 15549:2008-06 Air quality - Standard method for the measurement of the concentration of benzo[a]pyrene in ambient air
EN 12941:1998/A2:2008 RESPIRATORY PROTECTIVE DEVICES - POWERED FILTERING DEVICES INCORPORATING A HELMET OR A HOOD - REQUIREMENTS, TESTING, MARKING
DIN EN 14907:2005-11 AMBIENT AIR QUALITY - STANDARD GRAVIMETRIC MEASUREMENT METHOD FOR THE DETERMINATION OF THE PM[2,5] MASS FRACTION OF SUSPENDED PARTICULATE MATTER
EN 12341:2014 Ambient air - Standard gravimetric measurement method for the determination of the PM10 or PM2,5 mass concentration of suspended particulate matter
I.S. EN 14907:2005 AMBIENT AIR QUALITY - STANDARD GRAVIMETRIC MEASUREMENT METHOD FOR THE DETERMINATION OF THE PM[2,5] MASS FRACTION OF SUSPENDED PARTICULATE MATTER
BS EN 15549:2008 Air quality. Standard method for the measurement of the concentration of benzo(a)pyrene in ambient air
17/30359208 DC : 0 BS EN 14387 - RESPIRATORY PROTECTIVE DEVICES - GAS FILTER(S) AND COMBINED FILTER(S) - REQUIREMENTS, TESTING, MARKING
PREN 14387 : DRAFT 2017 RESPIRATORY PROTECTIVE DEVICES - GAS FILTER(S) AND COMBINED FILTER(S) - REQUIREMENTS, TESTING, MARKING
12/30260963 DC : 0 BS EN 12341 - AMBIENT AIR - STANDARD GRAVIMETRIC MEASUREMENT METHOD FOR THE DETERMINATION OF THE PM 10 OR PM 2,5 MASS CONCENTRATION OF SUSPENDED PARTICULATE MATTER
08/30178266 DC : DRAFT SEP 2008 BS EN 405 AMD1 - RESPIRATORY PROTECTIVE DEVICES - VALVED FILTERING HALF MASKS TO PROTECT AGAINST GASES OR GASES AND PARTICLES - REQUIREMENTS, TESTING, MARKING
S.R. CEN/TS 16645:2014 AMBIENT AIR - METHOD FOR THE MEASUREMENT OF BENZ[A]ANTHRACENE, BENZO[B]FLUORANTHENE, BENZO[J]FLUORANTHENE, BENZO[K]FLUORANTHENE, DIBENZ[A,H]ANTHRACENE, INDENO[1,2,3-CD]PYRENE AND BENZO[GHI]PERYLENE
DIN EN 12941:2009-02 RESPIRATORY PROTECTIVE DEVICES - POWERED FILTERING DEVICES INCORPORATING A HELMET OR A HOOD - REQUIREMENTS, TESTING, MARKING
DIN EN 12942:2009-02 RESPIRATORY PROTECTIVE DEVICES - POWER ASSISTED FILTERING DEVICES INCORPORATING FULL FACE MASKS, HALF MASKS OR QUARTER MASKS - REQUIREMENTS, TESTING, MARKING
DIN EN 14902 E : 2005 AMBIENT AIR QUALITY - STANDARD METHOD FOR THE MEASUREMENT OF PB, CD, AS AND NI IN THE PM10 FRACTION OF SUSPENDED PARTICULATE MATTER
DIN EN 14387 E : 2008 RESPIRATORY PROTECTIVE DEVICES - GAS FILTER(S) AND COMBINED FILTER(S) - REQUIREMENTS, TESTING, MARKING
DIN EN 14387:2008-05 Respiratory protective devices - Gas filter(s) and combined filter(s) - Requirements, testing, marking (includes Amendment A1:2008)
UNE-EN 12341:2015 Ambient air - Standard gravimetric measurement method for the determination of the PM10 or PM2,5 mass concentration of suspended particulate matter
I.S. EN 1827:1999 RESPIRATORY PROTECTIVE DEVICES - HALF MASKS WITHOUT INHALATION VALVES AND WITH SEPARABLE FILTERS TO PROTECT AGAINST GASES OR GASES AND PARTICLES OR PARTICLES ONLY - REQUIREMENTS, TESTING, MARKING
EN 14387:2004+A1:2008 Respiratory protective devices - Gas filter(s) and combined filter(s) - Requirements, testing, marking
DIN EN 12341:1999-03 AMBIENT AIR - STANDARD GRAVIMETRIC MEASUREMENT METHOD FOR THE DETERMINATION OF THE PM[10] OR PM[2],[5] MASS CONCENTRATION OF SUSPENDED PARTICULATE MATTER
I.S. EN 405:2002 RESPIRATORY PROTECTIVE DEVICES - VALVED FILTERING HALF MASKS TO PROTECT AGAINST GASES OR GASES AND PARTICLES - REQUIREMENTS, TESTING, MARKING
I.S. EN 12341:2014 AMBIENT AIR - STANDARD GRAVIMETRIC MEASUREMENT METHOD FOR THE DETERMINATION OF THE PM[10] OR PM[2,5] MASS CONCENTRATION OF SUSPENDED PARTICULATE MATTER
I.S. EN 14387:2004 RESPIRATORY PROTECTIVE DEVICES - GAS FILTER(S) AND COMBINED FILTER(S) - REQUIREMENTS, TESTING, MARKING
DIN EN 1827:2009-11 Respiratory protective devices - Half masks without inhalation valves and with separable filters to protect against gases or gases and particles or particles only - Requirements, testing, marking (includes Amendment A1:2009)
PREN 12941 : DRAFT 2016 RESPIRATORY PROTECTIVE DEVICES - POWERED FILTERING DEVICES INCORPORATING A LOOSE FITTING RESPIRATORY INTERFACE - REQUIREMENTS, TESTING, MARKING
I.S. EN 12942:1999 RESPIRATORY PROTECTIVE DEVICES - POWER ASSISTED FILTERING DEVICES INCORPORATING FULL FACE MASKS, HALF MASKS OR QUARTER MASKS - REQUIREMENTS, TESTING, MARKING
BS EN 16913:2017 Ambient air. Standard method for measurement of NO<sub>3</sub>$u-, SO<sub>4</sub><sup>2</sup>$u-, Cl$u-, NH<sub>4</sub>$u+, Na$u+, K$u+, Mg<sup>2</sup>$u+, Ca<sup>2</sup>$u+ in PM2,5 as deposited on filters
08/30178269 DC : 0 BS EN 1827:1999/A1 - RESPIRATORY PROTECTIVE DEVICES - HALF MASKS WITHOUT INHALATION VALVES AND WITH SEPARABLE FILTERS TO PROTECT AGAINST GASES OR GASES AND PARTICLES OR PARTICLES ONLY - REQUIREMENTS, TESTING, MARKING
PREN 12341 : DRAFT 2012 AMBIENT AIR - STANDARD GRAVIMETRIC MEASUREMENT METHOD FOR THE DETERMINATION OF THE PM 10 OR PM 2,5 MASS CONCENTRATION OF SUSPENDED PARTICULATE MATTER
PREN 12942 : DRAFT 2016 RESPIRATORY PROTECTIVE DEVICES - POWER FILTERING DEVICES INCORPORATING FULL FACE MASKS, HALF MASKS OR QUARTER MASKS - REQUIREMENTS, TESTING, MARKING
S.R. CEN/TR 16269:2011 AMBIENT AIR - GUIDE FOR THE MEASUREMENT OF ANIONS AND CATIONS IN PM2,5
I.S. EN 15549:2008 AIR QUALITY - STANDARD METHOD FOR THE MEASUREMENT OF THE CONCENTRATION OF BENZO[A]PYRENE IN AMBIENT AIR
DIN EN 12341:2014-08 Ambient air - Standard gravimetric measurement method for the determination of the PM or PM mass concentration of suspended particulate matter
DIN EN 149:2009-08 RESPIRATORY PROTECTIVE DEVICES - FILTERING HALF MASKS TO PROTECT AGAINST PARTICLES - REQUIREMENTS, TESTING, MARKING
DIN EN 405 : 2009-08 RESPIRATORY PROTECTIVE DEVICES - VALVED FILTERING HALF MASKS TO PROTECT AGAINST GASES OR GASES AND PARTICLES - REQUIREMENTS, TESTING, MARKING
BS EN 14907:2005 Ambient air quality. Standard gravimetric measurement method for the determination of the PM2,5 mass fraction of suspended particulate matter
BS EN 14902:2005 Ambient air quality. Standard method for the measurement of Pb, Cd, AS, and Ni in the PM 10 fraction of suspended particulate matter
UNI EN 1827 : 2009 RESPIRATORY PROTECTIVE DEVICES - HALF MASKS WITHOUT INHALATION VALVES AND WITH SEPARABLE FILTERS TO PROTECT AGAINST GASES OR GASES AND PARTICLES OR PARTICLES ONLY - REQUIREMENTS, TESTING, MARKING
UNI EN 12942 : 2009 RESPIRATORY PROTECTIVE DEVICES - POWER ASSISTED FILTERING DEVICES INCORPORATING FULL FACE MASKS, HALF MASKS OR QUARTER MASKS - REQUIREMENTS, TESTING, MARKING
UNI EN 405 : 2009 RESPIRATORY PROTECTIVE DEVICES - VALVED FILTERING HALF MASKS TO PROTECT AGAINST GASES OR GASES AND PARTICLES - REQUIREMENTS, TESTING, MARKING
UNI EN 12941 : 2009 RESPIRATORY PROTECTIVE DEVICES - POWERED FILTERING DEVICES INCORPORATING A HELMET OR A HOOD - REQUIREMENTS, TESTING, MARKING
UNI EN 14902 : 2005 AMBIENT AIR QUALITY - STANDARD METHOD FOR THE MEASUREMENT OF PB, CD, AS AND NI IN THE PM10 FRACTION OF SUSPENDED PARTICULATE MATTER
UNI EN 149 : 2009 RESPIRATORY PROTECTIVE DEVICES - FILTERING HALF MASKS TO PROTECT AGAINST PARTICLES - REQUIREMENTS, TESTING, MARKING
UNI EN 12341 : 2014 AMBIENT AIR - STANDARD GRAVIMETRIC MEASUREMENT METHOD FOR THE DETERMINATION OF THE PM10 OR PM2,5 MASS CONCENTRATION OF SUSPENDED PARTICULATE MATTER
I.S. EN 12941:1998 RESPIRATORY PROTECTIVE DEVICES - POWERED FILTERING DEVICES INCORPORATING A HELMET OR A HOOD - REQUIREMENTS, TESTING, MARKING
08/30178263 DC : DRAFT SEP 2008 BS EN 149 AMD1 - RESPIRATORY PROTECTIVE DEVICES - FILTERING HALF MASKS TO PROTECT AGAINST PARTICLES - REQUIREMENTS, TESTING, MARKING
UNI EN 15549 : 2008 AIR QUALITY - STANDARD METHOD FOR THE MEASUREMENT OF THE CONCENTRATION OF BENZO[A]PYRENE IN AMBIENT AIR
UNI EN 14387 : 2008 RESPIRATORY PROTECTIVE DEVICES - GAS FILTER(S) AND COMBINED FILTER(S) - REQUIREMENTS, TESTING, MARKING
I.S. EN 149:2001 RESPIRATORY PROTECTIVE DEVICES - FILTERING HALF MASKS TO PROTECT AGAINST PARTICLES - REQUIREMENTS, TESTING, MARKING
BS EN 405 : 2002 RESPIRATORY PROTECTIVE DEVICES - VALVED FILTERING HALF MASKS TO PROTECT AGAINST GASES OR GASES AND PARTICLES - REQUIREMENTS, TESTING, MARKING
BS EN 12941 : 1999 RESPIRATORY PROTECTIVE DEVICES - POWERED FILTERING DEVICES INCORPORATING A HELMET OR A HOOD - REQUIREMENTS, TESTING, MARKING
DIN EN 14902:2005-10 AMBIENT AIR QUALITY - STANDARD METHOD FOR THE MEASUREMENT OF PB, CD, AS AND NI IN THE PM10 FRACTION OF SUSPENDED PARTICULATE MATTER
EN 1827:1999+A1:2009 Respiratory protective devices - Half masks without inhalation valves and with separable filters to protect against gases or gases and particles or particles only - Requirements, testing, marking
EN 14902:2005/AC:2006 AMBIENT AIR QUALITY - STANDARD METHOD FOR THE MEASUREMENT OF PB, CD, AS AND NI IN THE PM10 FRACTION OF SUSPENDED PARTICULATE MATTER
EN 405:2001+A1:2009 Respiratory protective devices - Valved filtering half masks to protect against gases or gases and particles - Requirements, testing, marking
EN 14907:2005 Ambient air quality - Standard gravimetric measurement method for the determination of the PM2,5 mass fraction of suspended particulate matter
EN 15549:2008 Air quality - Standard method for the measurement of the concentration of benzo[a]pyrene in ambient air
EN 149:2001+A1:2009 Respiratory protective devices - Filtering half masks to protect against particles - Requirements, testing, marking
DIN EN 15549 E : 2008 AIR QUALITY - STANDARD METHOD FOR THE MEASUREMENT OF THE CONCENTRATION OF BENZO[A]PYRENE IN AMBIENT AIR
I.S. EN 16913:2017 AMBIENT AIR - STANDARD METHOD FOR MEASUREMENT OF NO[3][-], SO[4][2-], CL[-], NH[4][+], NA[+], K[+], MG[2+], CA[2+] IN PM2,5 AS DEPOSITED ON FILTERS
PD CEN/TS 16645:2014 Ambient air. Method for the measurement of benz[a]anthracene, benzo[b]fluoranthene, benzo[j]fluoranthene, benzo[k]fluoranthene, dibenz[a,h]anthracene, indeno[1,2,3-cd]pyrene and benzo[ghi]perylene
UNI CEN/TS 16645 : 2014 AMBIENT AIR - METHOD FOR THE MEASUREMENT OF BENZ[A]ANTHRACENE, BENZO[B]FLUORANTHENE, BENZO[J]FLUORANTHENE, BENZO[K]FLUORANTHENE, DIBENZ[A,H]ANTHRACENE, INDENO[1,2,3-CD]PYRENE AND BENZO[GHI]PERYLENE
EN 16913:2017 Ambient air - Standard method for measurement of NO3¯, SO4²¯, Cl¯, NH4+, Na+, K+, Mg²+, Ca²+ in PM2,5 as deposited on filters
DIN EN 16913:2015-10 (Draft) AMBIENT AIR - STANDARD METHOD FOR MEASUREMENT OF NO[3][-], SO[4][2-], CL[-], NH[4][+], NA[+], K[+], MG[2+], CA[2+] IN PM2,5 AS DEPOSITED ON FILTERS
BS EN 14387 : 2004 RESPIRATORY PROTECTIVE DEVICES - GAS FILTER(S) AND COMBINED FILTER(S) - REQUIREMENTS, TESTING, MARKING
BS EN 149 : 2001 RESPIRATORY PROTECTIVE DEVICES - FILTERING HALF MASKS TO PROTECT AGAINST PARTICLES - REQUIREMENTS, TESTING, MARKING
BS EN 12942 : 1999 RESPIRATORY PROTECTIVE DEVICES - POWER ASSISTED FILTERING DEVICES INCORPORATING FULL FACE MASKS, HALF MASKS OR QUARTER MASKS - REQUIREMENTS, TESTING, MARKING
BS EN 1827 : 1999 RESPIRATORY PROTECTIVE DEVICES - HALF MASKS WITHOUT INHALATION VALVES AND WITH SEPARABLE FILTERS TO PROTECT AGAINST GASES OR GASES AND PARTICLES OR PARTICLES ONLY - REQUIREMENTS, TESTING, MARKING
CEN/TR 16269:2011 Ambient air - Guide for the measurement of anions and cations in PM2,5
EN 12942:1998/A2:2008 RESPIRATORY PROTECTIVE DEVICES - POWER ASSISTED FILTERING DEVICES INCORPORATING FULL FACE MASKS, HALF MASKS OR QUARTER MASKS - REQUIREMENTS, TESTING, MARKING
CEN/TS 16645:2014 Ambient air - Method for the measurement of benz[a]anthracene, benzo[b]fluoranthene, benzo[j]fluoranthene, benzo[k]fluoranthene, dibenz[a,h]anthracene, indeno[1,2,3-cd]pyrene and benzo[ghi]perylene

89/106/EEC : 1988 COUNCIL DIRECTIVE OF 21 DECEMBER 1988 ON THE APPROXIMATION OF LAWS, REGULATIONS AND ADMINISTRATIVE PROVISIONS OF THE MEMBER STATES RELATING TO CONSTRUCTION PRODUCTS
EN 132:1998 Respiratory protective devices - Definitions of terms and pictograms
EN 13274-5:2001 Respiratory protective devices - Methods of test - Part 5: Climatic conditions

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more