EN 13617-3:2012
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
25-09-2021
14-03-2012
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Explosion protection measures
5 Construction
6 Physical properties
7 Operational requirements
8 Tests
9 Information for use
Annex A (normative) - Instructions - Guide for
items to be included in manufacturers'
installation and user manual
Annex B (normative) - Test methods
Annex C (informative) - Environmental aspects
Annex ZA (informative) - Relationship between this
European Standard and the Essential
Requirements of EU Directive 94/9/EC
This European Standard specifies safety and environmental requirements for the construction and performance of shear valves to be fitted to metering pumps, dispensers, and/or satellite delivery systems installed at petrol filling stations and used to dispense liquid fuels into the tanks of motor vehicles, boats and light aircraft and into portable containers at flow rates up to 200 l min-1.The requirements apply to shear valves at ambient temperatures from -20 °C to +40 °C with the possibility for an extended temperature range.It pays particular attention to mechanical and hydraulic characteristics.NOTE 1This European Standard does not apply to equipment for use with liquefied petroleum gas (LPG) or liquefied natural gas (LNG) or compressed natural gas (CNG).NOTE 2Fuels other than of Explosion Group IIA are excluded from this European Standard.
| Committee |
CEN/TC 393
|
| DevelopmentNote |
Supersedes PREN 13617-3. (04/2012)
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| BS EN 13617-3:2012 | Identical |
| UNE-EN 13617-3:2012 | Identical |
| NBN EN 13617-3 : 2012 | Identical |
| UNI EN 13617-3 : 2012 | Identical |
| SS-EN 13617-3:2012 | Identical |
| NEN EN 13617-3 : 2012 | Identical |
| NS EN 13617-3 : 2012 | Identical |
| DIN EN 13617-3:2018-11 (Draft) | Identical |
| DIN EN 13617-3:2012-05 | Identical |
| NF EN 13617-3 : 2012 | Identical |
| I.S. EN 13617-3:2012 | Identical |
| SN EN 13617-3 : 2012 | Identical |
| PN EN 13617-3 : 2012 | Identical |
| ONORM EN 13617-3 : 2012 | Identical |
| EN 12285-2 : 2005 | WORKSHOP FABRICATED STEEL TANKS - PART 2: HORIZONTAL CYLINDRICAL SINGLE SKIN AND DOUBLE SKIN TANKS FOR THE ABOVEGROUND STORAGE OF FLAMMABLE AND NON-FLAMMABLE WATER POLLUTING LIQUIDS |
| BS EN 15268:2008 | Petrol filling stations. Safety requirements for the construction of submersible pump assemblies |
| UNI EN 15268 : 2009 | PETROL FILLING STATIONS - SAFETY REQUIREMENTS FOR THE CONSTRUCTION OF SUBMERSIBLE PUMP ASSEMBLIES |
| I.S. EN 15268:2008 | PETROL FILLING STATIONS - SAFETY REQUIREMENTS FOR THE CONSTRUCTION OF SUBMERSIBLE PUMP ASSEMBLIES |
| DIN EN 12285-2:2005-05 | WORKSHOP FABRICATED STEEL TANKS - PART 2: HORIZONTAL CYLINDRICAL SINGLE SKIN AND DOUBLE SKIN TANKS FOR THE ABOVEGROUND STORAGE OF FLAMMABLE AND NON-FLAMMABLE WATER POLLUTING LIQUIDS |
| DIN EN 13617-1:2012-08 | Petrol filling stations - Part 1: Safety requirements for construction and performance of metering pumps, dispensers and remote pumping units |
| I.S. EN 13617-1:2012 | PETROL FILLING STATIONS - PART 1: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF METERING PUMPS, DISPENSERS AND REMOTE PUMPING UNITS |
| PREN 13617-1 : DRAFT 2010 | PETROL FILLING STATIONS - PART 1: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF METERING PUMPS, DISPENSERS AND REMOTE PUMPING UNITS |
| 10/30219405 DC : 0 | BS EN 13617-1 - PETROL FILLING STATIONS - PART 1: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF METERING PUMPS, DISPENSERS AND REMOTE PUMPING UNITS |
| DIN EN 15268 E : 2008 | PETROL FILLING STATIONS - SAFETY REQUIREMENTS FOR THE CONSTRUCTION OF SUBMERSIBLE PUMP ASSEMBLIES |
| EEMUA 186 : 2016 | A PRACTITIONER'S HANDBOOK FOR POTENTIALLY EXPLOSIVE ATMOSPHERES |
| UNI EN 13617-1 : 2012 | PETROL FILLING STATIONS - PART 1: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF METERING PUMPS, DISPENSERS AND REMOTE PUMPING UNITS |
| DIN EN 15268:2008-11 | PETROL FILLING STATIONS - SAFETY REQUIREMENTS FOR THE CONSTRUCTION OF SUBMERSIBLE PUMP |
| BS EN 13617-1:2012 | Petrol filling stations Safety requirements for construction and performance of metering pumps, dispensers and remote pumping units |
| UNE-EN 13617-1:2012 | Petrol filling stations - Part 1: Safety requirements for construction and performance of metering pumps, dispensers and remote pumping units |
| EN 15268:2008 | Petrol filling stations - Safety requirements for the construction of submersible pump assemblies |
| 08/30186475 DC : 0 | BS EN 13617-1 AMD1 - PETROL FILLING STATIONS - PART 1: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF METERING PUMPS, DISPENSERS AND REMOTE PUMPING UNITS |
| 05/30135286 DC : 0 | EN 15268 - PETROL FILLING STATIONS - SAFETY REQUIREMENTS FOR THE CONSTRUCTION AND PERFORMANCE OF SUBMERSIBLE PUMP ASSEMBLIES |
| EN 13617-1:2012 | Petrol filling stations - Part 1: Safety requirements for construction and performance of metering pumps, dispensers and remote pumping units |
| BS EN 12285-2:2005 | Workshop fabricated steel tanks Horizontal cylindrical single skin and double skin tanks for the aboveground storage of flammable and non-flammable water polluting liquids |
| EN 1127-1:2011 | Explosive atmospheres - Explosion prevention and protection - Part 1: Basic concepts and methodology |
| EN 60079-0:2012/A11:2013 | EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS (IEC 60079-0:2011, MODIFIED) |
| EN 976-1:1997 | Underground tanks of glass-reinforced plastics (GRP) - Horizontal cylindrical tanks for the non-pressure storage of liquid petroleum based fuels - Part 1: Requirements and test methods for single wall tanks |
| EN 13463-1:2009 | Non-electrical equipment for use in potentially explosive atmospheres - Part 1: Basic method and requirements |
| EN ISO 1182:2010 | Reaction to fire tests for products - Non-combustibility test (ISO 1182:2010) |
| ISO 1182:2010 | Reaction to fire tests for products Non-combustibility test |
| ISO 7-1:1994 | Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation |
| EN 13617-1:2012 | Petrol filling stations - Part 1: Safety requirements for construction and performance of metering pumps, dispensers and remote pumping units |
| 1994/9/EC : 1994 | DIRECTIVE 94/9/EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL OF 23 MARCH 1994 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES CONCERNING EQUIPMENT AND PROTECTIVE SYSTEMS INTENDED FOR USE IN POTENTIALLY EXPLOSIVE ATMOSPHERES |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.