Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

EN 13709:2010

Current
Current

The latest, up-to-date edition.

Industrial valves - Steel globe and globe stop and check valves
Published date

05-05-2010

Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Requirements
5 Test procedures
6 Declaration of compliance
7 Designation
8 Marking and preparation for storage and transportation
Annex A (informative) Information to be supplied by the
        purchaser
Annex ZA (informative) Relationship between this European
         Standard and the Essential Requirements of EU
         Directive 97/23/EC
Bibliography

This European Standard specifies the requirements for steel globe and globe stop and check valves which are wrought, cast or fabricated in straight, angle or oblique pattern with end connections flanged, butt welding, socket welding or threaded.This standard is applicable to steel globe and globe stop and check valves mainly used for industrial and general purpose applications. However, they can be used for other applications provided the requirements of the relevant performance standards are met.The range of nominal sizes covered is:DN 8; DN 10; DN 12; DN 15; DN 20; DN 25; DN 32; DN 40; DN 50; DN 65; DN 80; DN 100; DN 125; DN 150; DN 200; DN 250; DN 300; DN 350; DN 400.DN 8 and DN 12 are not used for PN designated flanged end connections.DN 8, DN 10 and DN 12 are not used for Class designated flanged end connections.Socket welding end valves and threaded end valves are limited to the range DN 8 to DN 65.The range of pressure designations covered is:a)for flanged and butt welding end valves:-PN 10; PN 16; PN 25; PN 40; PN 63; PN 100;-Class 150; Class 300; Class 600.b)for socket welding end valves and threaded end valves:-PN 40; PN 63; PN 100;-Class 600; Class 800.NOTEClass 800 is a Class designation widely used for socket welding and threaded end valves.

Committee
CEN/TC 69
DevelopmentNote
Supersedes PREN 13709. (11/2010)
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Current
Supersedes

Standards Relationship
SN EN 13709 : 2010 Identical
I.S. EN 13709:2010 Identical
NEN EN 13709 : 2010 Identical
BS EN 13709:2002 Identical
UNI EN 13709 : 2010 Identical
NS EN 13709 : 2010 Identical
UNE-EN 13709:2010 Identical
NF EN 13709 : 2010 Identical
PN EN 13709 : 2010 Identical
DIN EN 13709:2010-10 Identical
NBN EN 13709 : 2010 Identical
BS EN 13709:2010 Identical

EN 13175:2014 LPG EQUIPMENT AND ACCESSORIES - SPECIFICATION AND TESTING FOR LIQUEFIED PETROLEUM GAS (LPG) PRESSURE VESSEL VALVES AND FITTINGS
11/30243885 DC : 0 BS EN 13774 - VALVES FOR GAS DISTRIBUTION SYSTEMS WITH MAXIMUM OPERATING PRESSURE LESS THAN OR EQUAL TO 16 BAR - PERFORMANCE REQUIREMENTS
12/30250279 DC : 0 BS EN 12252 - LPG EQUIPMENT AND ACCESSORIES - EQUIPPING OF LPG ROAD TANKERS
UNI EN 13175 : 2015 LPG EQUIPMENT AND ACCESSORIES - SPECIFICATION AND TESTING FOR LIQUEFIED PETROLEUM GAS (LPG) PRESSURE VESSEL VALVES AND FITTINGS
I.S. EN 13175:2014 LPG EQUIPMENT AND ACCESSORIES - SPECIFICATION AND TESTING FOR LIQUEFIED PETROLEUM GAS (LPG) PRESSURE VESSEL VALVES AND FITTINGS
DIN EN 14678-2:2012-04 LPG equipment and accessories - Construction and performance of LPG equipment for automotive filling stations - Part 2: Components other than dispensers and installation requirements (includes Amendment A1:2012)
BS EN 14678-2 : 2007 LPG EQUIPMENT AND ACCESSORIES - CONSTRUCTION AND PERFORMANCE OF LPG EQUIPMENT FOR AUTOMOTIVE FILLING STATIONS - PART 2: COMPONENTS OTHER THAN DISPENSERS AND INSTALLATION REQUIREMENTS
I.S. EN 14678-2:2007 LPG EQUIPMENT AND ACCESSORIES - CONSTRUCTION AND PERFORMANCE OF LPG EQUIPMENT FOR AUTOMOTIVE FILLING STATIONS - PART 2: COMPONENTS OTHER THAN DISPENSERS AND INSTALLATION REQUIREMENTS
PREN 13774 : DRAFT 2011 VALVES FOR GAS DISTRIBUTION SYSTEMS WITH MAXIMUM OPERATING PRESSURE LESS THAN OR EQUAL TO 16 BAR - PERFORMANCE REQUIREMENTS
05/30125032 DC : DRAFT JUL 2005 EN 14678-2 - LPG EQUIPMENT AND ACCESSORIES - EQUIPMENT FOR LIQUEFIED PETROLEUM GAS AUTOMOTIVE FILLING STATIONS - PART 2: COMPONENTS OTHER THAN DISPENSERS, AND INSTALLATION REQUIREMENTS
S.R. CEN/TR 13932:2009 ROTODYNAMIC PUMPS - RECOMMENDATIONS FOR FITTING OF INLET AND OUTLET ON PIPING
CEN/TR 13932:2009 Rotodynamic pumps - Recommendations for fitting of inlet and outlet on piping
UNE-EN 16668:2016 Industrial valves - Requirements and testing for metallic valves as pressure accessories
UNE-EN 14678-2:2009 LPG equipment and accessories - Equipment for Liquefied Petroleum Gas automotive filling stations - Part 2: Components other than dispensers, and installation requirements
BS EN 13175:2014 LPG Equipment and accessories. Specification and testing for Liquefied Petroleum Gas (LPG) pressure vessel valves and fittings
DIN EN 12252:2014-07 LPG equipment and accessories - Equipping of LPG road tankers
BS EN 12252:2014 LPG equipment and accessories. Equipping of LPG road tankers
17/30362889 DC : 0 BS EN 13175 - LPG EQUIPMENT AND ACCESSORIES - SPECIFICATION AND TESTING FOR LIQUEFIED PETROLEUM GAS (LPG) PRESSURE VESSEL VALVES AND FITTINGS
I.S. EN 13774:2013 VALVES FOR GAS DISTRIBUTION SYSTEMS WITH MAXIMUM OPERATING PRESSURE LESS THAN OR EQUAL TO 16 BAR - PERFORMANCE REQUIREMENTS
DIN EN 12252:2000-10 LPG EQUIPMENT AND ACCESSORIES - EQUIPPING OF LPG ROAD TANKERS
I.S. EN 12252:2014 LPG EQUIPMENT AND ACCESSORIES - EQUIPPING OF LPG ROAD TANKERS
10/30218988 DC : 0 BS EN 13175 - LPG EQUIPMENT AND ACCESSORIES - SPECIFICATION AND TESTING FOR LIQUEFIED PETROLEUM GAS (LPG) TANK VALVES AND FITTINGS
14/30300117 DC : 0 BS EN 13175 - LPG EQUIPMENT AND ACCESSORIES - SPECIFICATION AND TESTING FOR LIQUEFIED PETROLEUM GAS (LPG) PRESSURE VESSEL VALVES AND FITTINGS
UNI CEN/TR 13932 : 2009 ROTODYNAMIC PUMPS - RECOMMENDATIONS FOR FITTING OF INLET AND OUTLET ON PIPING
PD CEN/TR 13932:2009 Rotodynamic pumps. Recommendations for fitting of inlet and outlet on piping
BS EN 16668 : 2016 INDUSTRIAL VALVES - REQUIREMENTS AND TESTING FOR METALLIC VALVES AS PRESSURE ACCESSORIES
UNI EN 13774 : 2013 VALVES FOR GAS DISTRIBUTION SYSTEMS WITH MAXIMUM OPERATING PRESSURE LESS THAN OR EQUAL TO 16 BAR - PERFORMANCE REQUIREMENTS
UNI EN 14678-2 : 2012 LPG EQUIPMENT AND ACCESSORIES - CONSTRUCTION AND PERFORMANCE OF LPG EQUIPMENT FOR AUTOMOTIVE FILLING STATIONS - PART 2: COMPONENTS OTHER THAN DISPENSERS AND INSTALLATION REQUIREMENTS
UNI EN 12252 : 2014 LPG EQUIPMENT AND ACCESSORIES - EQUIPPING OF LPG ROAD TANKERS
13/30281067 DC : 0 BS EN 12252 - LPG EQUIPMENT AND ACCESSORIES - EQUIPPING OF LPG ROAD TANKERS
UNE-EN 13175:2015 LPG Equipment and accessories - Specification and testing for Liquefied Petroleum Gas (LPG) pressure vessel valves and fittings
03/118134 DC : DRAFT NOV 2003 EN 12252 - EQUIPPING OF LIQUEFIED PETROLEUM GAS (LPG) ROAD TANKERS
DIN EN 13774:2013-05 VALVES FOR GAS DISTRIBUTION SYSTEMS WITH MAXIMUM OPERATING PRESSURE LESS THAN OR EQUAL TO 16 BAR - PERFORMANCE REQUIREMENTS
BS EN 13774:2013 Valves for gas distribution systems with maximum operating pressure less than or equal to 16 bar. Performance requirements
UNE-EN 13774:2013 Valves for gas distribution systems with maximum operating pressure less than or equal to 16 bar - Performance requirements
EN 13774:2013 Valves for gas distribution systems with maximum operating pressure less than or equal to 16 bar - Performance requirements
EN 16668:2016+A1:2018 Industrial valves - Requirements and testing for metallic valves as pressure accessories
EN 14678-2:2007+A1:2012 LPG equipment and accessories - Construction and performance of LPG equipment for automotive filling stations - Part 2: Components other than dispensers and installation requirements
PREN 12252 : DRAFT 2013 LPG EQUIPMENT AND ACCESSORIES - EQUIPPING OF LPG ROAD TANKERS
I.S. EN 16668:2016 INDUSTRIAL VALVES - REQUIREMENTS AND TESTING FOR METALLIC VALVES AS PRESSURE ACCESSORIES
DIN EN 13175:2015-02 LPG EQUIPMENT AND ACCESSORIES - SPECIFICATION AND TESTING FOR LIQUEFIED PETROLEUM GAS (LPG) PRESSURE VESSEL VALVES AND FITTINGS
EN 12252:2014 LPG equipment and accessories - Equipping of LPG road tankers

EN 12982:2009 Industrial valves - End-to-end and centre-to-end dimensions for butt welding end valves
ISO 5210:2017 Industrial valves — Multi-turn valve actuator attachments
EN ISO 5210:2017 Industrial valves - Multi-turn valve actuator attachments (ISO 5210:2017)
EN 1759-1:2004 Flanges and their joint - Circular flanges for pipes, valves, fittings and accessories, Class designated - Part 1: Steel flanges, NPS 1/2 to 24
EN 1503-1:2000 Valves - Materials for bodies, bonnets and covers - Part 1: Steels specified in European Standards
EN 558:2017 Industrial valves - Face-to-face and centre-to-face dimensions of metal valves for use in flanged pipe systems - PN and Class designated valves
EN 12266-2:2012 Industrial valves - Testing of metallic valves - Part 2: Tests, test procedures and acceptance criteria - Supplementary requirements
EN 12516-1:2014 Industrial valves - Shell design strength - Part 1: Tabulation method for steel valve shells
EN 736-2:2016 Valves - Terminology - Part 2: Definition of components of valves
EN 10045-1 : 1990 METALLIC MATERIALS - CHARPY IMPACT TEST - PART 1: TEST METHOD
EN ISO 228-1:2003 Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000)
EN 12266-1:2012 Industrial valves - Testing of metallic valves - Part 1: Pressure tests, test procedures and acceptance criteria - Mandatory requirements
ASME B1.20.1 : 2013(R2018) PIPE THREADS, GENERAL PURPOSE (INCH)
ISO 7-1:1994 Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation
EN 12351:2010 Industrial valves - Protective caps for valves with flanged connections
EN 12516-3:2002/AC:2003 VALVES - SHELL DESIGN STRENGTH - PART 3: EXPERIMENTAL METHOD
EN 12570:2000 Industrial valves - Method for sizing the operating element
EN 12760:2016 Industrial valves - Socket welding ends for steel valves
EN 12516-2:2014 Industrial valves - Shell design strength - Part 2: Calculation method for steel valve shells
ISO 15607:2003 Specification and qualification of welding procedures for metallic materials General rules
EN 1418:1997 Welding personnel - Approval testing of welding operators for fusion welding and resistance weld setters for fully mechanized and automatic welding of metallic materials
EN 19:2016 Industrial valves - Marking of metallic valves
ISO 228-1:2000 Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation
EN 736-3:2008 Valves - Terminology - Part 3: Definition of terms
EN ISO 15607:2003 Specification and qualification of welding procedures for metallic materials - General rules (ISO 15607:2003)
1997/23/EC : 1997 DIRECTIVE 97/23/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 29 MAY 1997 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES CONCERNING PRESSURE EQUIPMENT
EN 287-1:2011 Qualification test of welders - Fusion welding - Part 1: Steels

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more