Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

EN 13766:2010

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Thermoplastic multi-layer (non-vulcanized) hoses and hose assemblies for the transfer of liquid petroleum gas and liquefied natural gas - Specification
Superseded date

25-01-2019

Published date

02-06-2010

Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Classification
5 Materials and construction
6 Dimensions
7 Performance requirements of hoses and hose assemblies
8 Test frequency
9 Type tests
10 Marking
Annex A (normative) - Crush recovery test
Annex B (normative) - Method of test for thermal ageing
Annex C (normative) - Method of test of fittings subjected
        to low temperatures
Annex D (normative) - Sequence of hydrostatic tests
Annex E (normative) - Method of test for fitting security
Annex F (normative) - Method of test for leak tightness
Annex G (normative) - Type and routine tests for hoses and
        hose assemblies
Annex H (informative) - Batch tests for hoses and hose
        assemblies
Bibliography

This European Standard specifies requirements for two types of thermoplastic multi-layer (non-vulcanized) transfer hoses and hose assemblies for carrying liquefied petroleum gas and liquefied natural gas. Each type is subdivided into two classes, one for onshore duties, and the other for offshore.This European Standard is applicable for hose sizes from 25 mm to 250 mm, working pressures from 10,5 bar to 25 bar and operating temperatures from - 196 °C to + 45 °C.NOTEOffshore LNG hose assemblies are also specified in EN 1474-2.WARNING - Persons using this European Standard should be familiar with normal laboratory practice.This standard does not purport to address all the safety problems, if any, associated with its use. It is the responsibility of the user to establish appropriate health and safety practices and to ensure compliance with any national regulatory conditions.

Committee
CEN/TC 218
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Superseded
SupersededBy

18/30369304 DC : DRAFT APR 2018 BS EN 1473 - INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN OF ONSHORE INSTALLATIONS
DIN EN 1473:2016-10 Installation and equipment for liquefied natural gas - Design of onshore installations
BS EN 1473:2016 Installation and equipment for liquefied natural gas. Design of onshore installations
DIN EN 1473:1997-11 INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN OF ONSHORE INSTALLATIONS
DIN EN 14420-1:2013-09 Hose fittings with clamp units - Part 1: Requirements, types of fixing and connection, designation and testing
EN 12115:2011 Rubber and thermoplastics hoses and hose assemblies for liquid or gaseous chemicals - Specification
I.S. EN 12115:2011 RUBBER AND THERMOPLASTICS HOSES AND HOSE ASSEMBLIES FOR LIQUID OR GASEOUS CHEMICALS - SPECIFICATION
I.S. EN 1473:2016 INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN OF ONSHORE INSTALLATIONS
I.S. EN 14420-1:2013 HOSE FITTINGS WITH CLAMP UNITS - PART 1: REQUIREMENTS, TYPES OF FIXING AND CONNECTION, DESIGNATION AND TESTING
06/30158810 DC : 0 BS EN 1474-2 - INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN AND TESTING OF MARINE TRANSFER SYSTEMS - PART 2: DESIGN AND TESTING OF TRANSFER HOSES
PREN 1473 : DRAFT 2018 INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN OF ONSHORE INSTALLATIONS
DIN EN 1474-2:2009-02 Installation and equipment for liquefied natural gas - Design and testing of marine transfer systems - Part 2: Design and testing of transfer hoses
EN 1473:2016 Installation and equipment for liquefied natural gas - Design of onshore installations
05/30128234 DC : DRAFT FEB 2005 EN 1473 - INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN OF ONSHORE INSTALLATIONS
BS EN 1474-2:2008 Installation and equipment for liquefied natural gas. Design and testing of marine transfer systems Design and testing of transfer hoses
I.S. EN 1474-2:2008 INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN AND TESTING OF MARINE TRANSFER SYSTEMS - PART 2: DESIGN AND TESTING OF TRANSFER HOSES
UNI EN 1474-2 : 2009 INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN AND TESTING OF MARINE TRANSFER SYSTEMS - PART 2: DESIGN AND TESTING OF TRANSFER HOSES
DIN EN 12115:2011-04 Rubber and thermoplastics hoses and hose assemblies for liquid or gaseous chemicals - Specification; German version EN 12115:2011
EN 1474-2:2008 Installation and equipment for liquefied natural gas - Design and testing of marine transfer systems - Part 2: Design and testing of transfer hoses
UNI EN 14420-1 : 2013 HOSE FITTINGS WITH CLAMP UNITS - PART 1: REQUIREMENTS, TYPES OF FIXING AND CONNECTION, DESIGNATION AND TESTING
10/30234625 DC : 0 BS EN 14420-1 - HOSE FITTINGS WITH CLAMP UNITS - PART 1: REQUIREMENTS, SURVEY, DESIGNATION AND TESTING
BS EN 12115:2011 Rubber and thermoplastics hoses and hose assemblies for liquid or gaseous chemicals. Specification
BS EN 14420-1:2013 Hose fittings with clamp units Requirements, types of fixing and connection, designation and testing
EN 14420-1:2013 Hose fittings with clamp units - Part 1: Requirements, types of fixing and connection, designation and testing
PREN 14420-1 : DRAFT 2010 HOSE FITTINGS WITH CLAMP UNITS - PART 1: REQUIREMENTS, SURVEY, DESIGNATION AND TESTING
14/30297213 DC : 0 BS EN 1473 - INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN OF ONSHORE INSTALLATIONS
UNI EN 12115 : 2011 RUBBER AND THERMOPLASTICS HOSES AND HOSE ASSEMBLIES FOR LIQUID OR GASEOUS CHEMICALS - SPECIFICATION

ISO 13934-1:2013 Textiles — Tensile properties of fabrics — Part 1: Determination of maximum force and elongation at maximum force using the strip method
EN ISO 8330:2014 Rubber and plastics hoses and hose assemblies - Vocabulary (ISO 8330:2014)
EN ISO 1402:2009 Rubber and plastics hoses and hose assemblies - Hydrostatic testing (ISO 1402:2009)
EN ISO 4671:2007/A1:2011 Rubber and plastics hoses and hose assemblies - Methods of measurement of the dimensions of hoses and the lengths of hose assemblies - Amendment 1: Clarification of position at which outside diameter is measured (ISO 4671:2007/Amd 1:2011)
EN ISO 13934-1:2013 Textiles - Tensile properties of fabrics - Part 1: Determination of maximum force and elongation at maximum force using the strip method (ISO 13934-1:2013)
EN ISO 1043-1:2011/A1:2016 PLASTICS - SYMBOLS AND ABBREVIATED TERMS - PART 1: BASIC POLYMER AND THEIR SPECIAL CHARACTERISTICS (ISO 1043-1:2011/AMD 1:2016)
ISO 4672:1997 Rubber and plastics hoses Sub-ambient temperature flexibility tests
EN 10088-3:2014 Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes
EN 1474-2:2008 Installation and equipment for liquefied natural gas - Design and testing of marine transfer systems - Part 2: Design and testing of transfer hoses
EN ISO 8031:2009 Rubber and plastics hoses and hose assemblies - Determination of electrical resistance and conductivity (ISO 8031:2009)
EN ISO 4672 : 1999 RUBBER AND PLASTICS HOSES - SUB-AMBIENT TEMPERATURE FLEXIBILITY TESTS
EN ISO 527-1:2012 Plastics - Determination of tensile properties - Part 1: General principles (ISO 527-1:2012)
EN ISO 7326:2016 Rubber and plastics hoses - Assessment of ozone resistance under static conditions (ISO 7326:2016)
ISO 7326:2016 Rubber and plastics hoses Assessment of ozone resistance under static conditions
EN 10045-1 : 1990 METALLIC MATERIALS - CHARPY IMPACT TEST - PART 1: TEST METHOD
ISO 8330:2007 Rubber and plastics hoses and hose assemblies Vocabulary
ISO 4671:2007 Rubber and plastics hoses and hose assemblies Methods of measurement of the dimensions of hoses and the lengths of hose assemblies
ISO 1402:2009 Rubber and plastics hoses and hose assemblies Hydrostatic testing
ISO 1043-1:2011 Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics
ISO 8031:2009 Rubber and plastics hoses and hose assemblies Determination of electrical resistance and conductivity
ISO 527-1:2012 Plastics Determination of tensile properties Part 1: General principles

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more