Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

EN 13828:2003

Current
Current

The latest, up-to-date edition.

Building valves - Manually operated copper alloy and stainless steel ball valves for potable water supply in buildings -Tests and requirements
Published date

17-09-2003

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Designation
5 Design requirements
  5.1 Materials
      5.1.1 Body and ball materials
  5.2 End connections
  5.3 Operation
      5.3.1 Operating devices
  5.4 Stops
  5.5 Ball bore
      5.5.1 Full bore
      5.5.2 Reduced bore
6 Performance requirements
  6.1 Operating torque
  6.2 Stop resistance
  6.3 Leak-tightness
  6.4 Angular seal
7 Test methods
  7.1 Operating torque test
  7.2 Torque and bending test
      7.2.1 General
      7.2.2 Sequence of torsion and bending moments tests for valves
  7.3 Stops and spindle - Mechanical resistance test
  7.4 Hydraulic tests
      7.4.1 Leak-tightness test
      7.4.2 Hydraulic strength
  7.5 Acoustic tests and requirements
      7.5.1 Principle
      7.5.2 Test
      7.5.3 Requirements
  7.6 Endurance test
      7.6.1 Endurance test
      7.6.2 Test installation
      7.6.3 Test
  7.7 Angular seal
8 Marking
Bibliography

This European standard applies primarily to copper alloy ball valves, dimensions DN 8 to DN 100, for potable water supply in buildings up to PN 10 and a distribution temperature of 65 °C. Occasional excursions up to 90 °C are permitted for a period of 1 h maximum.This standard applies also to ball valves in combination with other components in the same body.This standard specifies:- the requirements of the materials and the design of ball valves;- the mechanical, hydraulic and acoustic requirements of ball valves;- the test methods to verify the requirements of ball valves;- the marking requirements of ball valves.Ball valves in combination with other valves should fulfil the same requirements.

Committee
CEN/TC 164
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Current

Standards Relationship
NF EN 13828 : 2004 Identical
NBN EN 13828 : 2003 Identical
NEN EN 13828 : 2003 Identical
NS EN 13828 : 1ED 2003 Identical
I.S. EN 13828:2003 Identical
PN EN 13828 : 2005 Identical
UNE-EN 13828:2004 Identical
SN EN 13828 : 2003 Identical
UNI EN 13828 : 2004 Identical
BS EN 13828:2003 Identical
DIN EN 13828:2003-12 Identical

DIN EN 15092:2008-09 BUILDING VALVES - INLINE HOT WATER SUPPLY TEMPERING VALVES - TESTS AND REQUIREMENTS
04/30126822 DC : 0 EN 15092 - BUILDING VALVES - INLINE HOT WATER SUPPLY TEMPERING VALVES - TESTS AND REQUIREMENTS
DIN EN 15092 E : 2008 BUILDING VALVES - INLINE HOT WATER SUPPLY TEMPERING VALVES - TESTS AND REQUIREMENTS
I.S. EN 15092:2008 BUILDING VALVES - INLINE HOT WATER SUPPLY TEMPERING VALVES - TESTS AND REQUIREMENTS
BS EN 15092:2008 Building valves. Inline hot water supply tempering valves. Tests and requirements
EN 15092:2008 Building valves - Inline hot water supply tempering valves - Tests and requirements
UNI EN 15092 : 2008 BUILDING VALVES - INLINE HOT WATER SUPPLY TEMPERING VALVES - TESTS AND REQUIREMENTS

ISO 3822-1:1999 Acoustics Laboratory tests on noise emission from appliances and equipment used in water supply installations Part 1: Method of measurement
EN 1254-3:1998 Copper and copper alloys - Plumbing fittings - Part 3: Fittings with compression ends for use with plastics pipes
EN 1254-1:1998 Copper and copper alloys - Plumbing fittings - Part 1: Fittings with ends for capillary soldering or capillary brazing to copper tubes
EN 1254-2:1998 Copper and copper alloys - Plumbing fittings - Part 2: Fittings with compression ends for use with copper tubes
ISO 7005-3:1988 Metallic flanges Part 3: Copper alloy and composite flanges
ISO 6708:1995 Pipework components Definition and selection of DN (nominal size)
EN ISO 6708:1995 Pipework components - Definition and selection of DN (nominal size) (ISO 6708:1995)
EN 10272:2016 Stainless steel bars for pressure purposes
ISO 7-1:1994 Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation
ISO 65:1981 Carbon steel tubes suitable for screwing in accordance with ISO 7-1
ISO 6509:1981 Corrosion of metals and alloys Determination of dezincification resistance of brass
EN 12164:2016 Copper and copper alloys - Rod for free machining purposes
ISO 261:1998 ISO general purpose metric screw threads General plan
ISO 3822-3:1997 Acoustics Laboratory tests on noise emission from appliances and equipment used in water supply installations Part 3: Mounting and operating conditions for in-line valves and appliances
EN ISO 3822-1:1999/A1:2008 ACOUSTICS - LABORATORY TESTS ON NOISE EMISSION FROM APPLIANCES AND EQUIPMENT USED IN WATER SUPPLY INSTALLATIONS - PART 1: METHOD OF MEASUREMENT
EN 12420:2014 Copper and copper alloys - Forgings
EN ISO 6509 : 1995 CORROSION OF METALS AND ALLOYS - DETERMINATION OF DEZINCIFICATION RESISTANCE OF BRASS
EN 12165:2016 COPPER AND COPPER ALLOYS - WROUGHT AND UNWROUGHT FORGING STOCK
EN 331:2015 Manually operated ball valves and closed bottom taper plug valves for gas installations for buildings
EN 10213-4 : 1995 TECHNICAL DELIVERY CONDITIONS FOR STEEL CASTINGS FOR PRESSURE PURPOSES - PART 4: AUSTENITIC AND AUSTENITIC-FERRITIC STEEL GRADES
EN 1982:2017 Copper and copper alloys - Ingots and castings
ISO 228-1:2000 Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more