Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

EN 14154-1:2005+A2:2011

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Water meters - Part 1: General requirements
Superseded date

09-11-2021

Published date

06-04-2011

Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Technical characteristics
5 Meter classification
6 Marking
7 Metrological characteristics
8 Meter performance requirements
9 Metrological control
Annex A (normative) - Checking facilities
Annex B (normative) - In-line meter dimensions
        (including alternative lengths)
Annex C (informative) - Table of rated operating,
        limiting and references conditions
Annex D (informative) - Test program
Annex ZA (informative) - Relationship between this
         European Standard and the Essential
         Requirements of EU Directive 22/2004/EC
         on Measuring Instruments
Bibliography

This document applies to water meters intended for residential, commercial, light industrial and industrial use, and specifies the requirements and certification procedures for water meters, irrespective of the design technologies used to meter the actual volume of clean cold potable water or heated water, flowing through a fully charged, closed conduit. These water meters shall incorporate devices, which indicate the integrated volume.This document also applies to water meters based on electrical or electronic principles, and to water meters based on mechanical principles incorporating electronic devices, used to meter the actual volume flow of cold potable water or heated water. It provides metrological requirements for electronic ancillary devices when they are subject to metrological control. As a rule the ancillary devices are optional. However national or international regulations make some ancillary devices mandatory in relation to the utilisation of the water meter.

Committee
CEN/TC 92
DevelopmentNote
2005 Edition Re-Issued in April 2011 & incorporates AMD 2 2011. (05/2011)
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Superseded
SupersededBy

I.S. EN 14154-4:2014 WATER METERS - PART 4: ADDITIONAL FUNCTIONALITIES
DIN EN 14268 E : 2005 IRRIGATION TECHNIQUES - METERS FOR IRRIGATION WATER
DIN EN 14154-2:2011-06 WATER METERS - PART 2: INSTALLATION AND CONDITIONS OF USE
DIN EN 14154-4:2015-02 Water meters - Part 4: Additional functionalities
DIN EN 14154-4 E : 2015 WATER METERS - PART 4: ADDITIONAL FUNCTIONALITIES
DIN EN 14268:2005-11 IRRIGATION TECHNIQUES - METERS FOR IRRIGATION WATER
BS EN 14154-2 : 2005 WATER METERS - PART 2: INSTALLATION AND CONDITIONS OF USE
BS EN 14154-3 : 2005 WATER METERS - PART 3: TEST METHODS AND EQUIPMENT
VDI 2077 Blatt 2:2012-01 Energy consumption accounting for the building services - Water supply systems
BS EN 14154-4:2014 Water meters Additional functionalities
UNE-EN 14154-3:2005 Water meters - Part 3 : Test methods and equipment
UNE-EN 14154-2:2005 Water meters - Part 2 : Installation and conditions of use
UNI EN 14268 : 2006 IRRIGATION TECHNIQUES - METERS FOR IRRIGATION WATER
UNI EN 14154-3 : 2011 WATER METERS - PART 3: TEST METHODS AND EQUIPMENT
UNI EN 14154-2 : 2011 WATER METERS - PART 2: INSTALLATION AND CONDITIONS OF USE
ISO 20456:2017 Measurement of fluid flow in closed conduits — Guidance for the use of electromagnetic flowmeters for conductive liquids
BS EN 14268:2005 Irrigation techniques. Meters for irrigation water
EN 14154-2:2005+A2:2011 Water meters - Part 2: Installation and conditions of use
EN 14154-3:2005+A2:2011 Water meters - Part 3: Test methods and equipment
EN 14154-4:2014 Water meters - Part 4: Additional functionalities
EN 14268:2005/AC:2007 IRRIGATION TECHNIQUES - METERS FOR IRRIGATION WATER
UNE-EN 14154-4:2015 Water meters - Part 4: Additional functionalities
UNI EN 14154-4 : 2015 WATER METERS - PART 4: ADDITIONAL FUNCTIONALITIES
DIN EN 14154-3:2011-06 WATER METERS - PART 3: TEST METHODS AND EQUIPMENT

ISO 7005-2:1988 Metallic flanges — Part 2: Cast iron flanges
2004/22/EC : 2004 DIRECTIVE 2004/22/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 31 MARCH 2004 ON MEASURING INSTRUMENTS
ISO 7005-3:1988 Metallic flanges Part 3: Copper alloy and composite flanges
ISO 3:1973 Preferred numbers Series of preferred numbers
EN ISO 6708:1995 Pipework components - Definition and selection of DN (nominal size) (ISO 6708:1995)
EN ISO 228-1:2003 Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000)
ISO/IEC Guide 99:2007 International vocabulary of metrology Basic and general concepts and associated terms (VIM)
EN 14154-3:2005+A2:2011 Water meters - Part 3: Test methods and equipment
EN 14154-2:2005+A2:2011 Water meters - Part 2: Installation and conditions of use
EN 1333:2006 Flanges and their joints - Pipework components - Definition and selection of PN
OIML R 49-1 : 2013 WATER METERS FOR COLD POTABLE WATER AND HOT WATER - PART 1: METROLOGICAL AND TECHNICAL REQUIREMENTS
OIML R 49-2 : 2013 WATER METERS FOR COLD POTABLE WATER AND HOT WATER - PART 2: TEST METHODS
ENV 13005 : DRAFT 1999 GUIDE TO THE EXPRESSION OF UNCERTAINTY IN MEASUREMENT
ISO 7858-1:1998 Measurement of water flow in closed conduits Combination meters for cold potable water Part 1: Specifications
ISO 6807:2003 Rubber hoses and hose assemblies for rotary drilling and vibration applications Specification
ISO 228-1:2000 Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more