EN 1473:2016
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Installation and equipment for liquefied natural gas - Design of onshore installations
Superseded date
22-05-2021
Published date
18-05-2016
Publisher
European foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Safety and environment
5 Jetties and marine facilities
6 Storage and retention systems
7 LNG pumps
8 Vaporization of LNG
9 Pipe-work
10 Reception/send out of natural gas
11 Boil off recovery and treatment plants
12 Auxiliary circuits and buildings
13 Hazard management
14 Control and monitoring systems
15 Construction, commissioning and turnaround
16 Preservation and corrosion protection
17 Training for operations
18 Pre-operational marine training
Annex A (normative) - Thermal radiation threshold
values
Annex B (normative) - Definitions of reference flow
rates
Annex C (informative) - Seismic classification
Annex D (normative) - Specific requirements for LNG
pumps
Annex E (normative) - Specific requirements for LNG
vaporizers
Annex F (normative) - Criteria for the design of pipes
Annex G (informative) - Description of the different types
of onshore LNG installations
Annex H (informative) - Definition of different types of
LNG tanks
Annex I (informative) - Frequency ranges
Annex J (informative) - Classes of consequence
Annex K (informative) - Levels of risk
Annex L (informative) - Typical process steps of liquefaction
Annex M (informative) - Odourant systems
Bibliography
This European Standard gives guidelines for the design, construction and operation of all onshore liquefied natural gas (LNG) installations for the liquefaction, storage, vaporization, transfer and handling of LNG.This European Standard is valid for plants with LNG storage at pressure lower than 0.5 barg and capacity above 200 t and for the following plant types:-LNG liquefaction installations (plant), between the designated gas inlet boundary limit, and the outlet boundary limit which is usually the ship manifold and/or truck delivery station when applicable; feed gas can be from gas field, associated gas from oil field, piped gas from transportation grid or from renewables;-LNG regasification installations (plant), between the ship manifold and the designated gas outlet boundary limit;-peak-shaving plants, between designated gas inlet and outlet boundary limits;-the fix part of LNG bunkering station.A short description of each of these installations is given in Annex G.Floating solutions (FPSO, FSRU, SRV), whether off-shore or nearby shore, are not covered by this European Standard even if some concepts, principles or recommendations could be applied. However, in case of berthed FSRU with LNG transfer across the jetty, the following recommendations apply for the jetty and topside facilities if the jetty is located within 3 000 m from the shore line.In case of FSU type solution, the tank safety functions as defined in Clause 6 shall be checked and implemented. The on-shore part is covered by these standard recommendations.This standard is not applicable for installations not specifically referred or covered by other standards, e.g. LNG fuelling stations, LNG road or rail tankers and LNG bunkering vessels.The plants with a storage inventory from 50 t up to 200 t with tanks at a pressure higher than 0.5 barg are covered by EN 13645. For plants with a larger inventory and with storage pressure over 0.5 barg, the storage vessels shall comply with EN 13445 and their impacts on the plant safety shall be appraised during the QRA.
| Committee |
CEN/TC 282
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| ONORM EN 1473 : 2016 | Identical |
| DIN EN 1473:1997-11 | Identical |
| I.S. EN 1473:2016 | Identical |
| UNI EN 1473 : 2016 | Identical |
| NBN EN 1473 : 2016 | Identical |
| NF EN 1473 : 2017 | Identical |
| SS-EN 1473 : 2016 | Identical |
| SN EN 1473 : 2016 | Identical |
| BS EN 1473:2016 | Identical |
| PN EN 1473 : 2016 | Identical |
| UNE-EN 1473:2017 | Identical |
| UNI EN 1473 : 2007 | Identical |
| NEN EN 1473 : 2016 | Identical |
| DIN EN 1473:2016-10 | Identical |
| NS EN 1473 : 1997 | Identical |
| DIN EN ISO 28460:2011-04 | Petroleum and natural gas industries - Installation and equipment for liquefied natural gas - Ship-to-shore interface and port operations (ISO 28460:2010) |
| DIN EN ISO 16903:2015-11 | PETROLEUM AND NATURAL GAS INDUSTRIES - CHARACTERISTICS OF LNG, INFLUENCING THE DESIGN AND MATERIAL SELECTION (ISO 16903:2015) |
| 06/30150265 DC : 0 | EN 1474-1 - INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN AND TESTING OF MARINE TRANSFER SYSTEMS - PART 1: DESIGN AND TESTING OF TRANSFER ARMS |
| UNI EN 1474-1 : 2009 | INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN AND TESTING OF MARINE TRANSFER SYSTEMS - PART 1: DESIGN AND TESTING OF TRANSFER ARMS |
| BS EN 1474-3:2008 | Installation and equipment for liquefied natural gas. Design and testing of marine transfer systems Offshore transfer systems |
| EN ISO 16903:2015 | Petroleum and natural gas industries - Characteristics of LNG, influencing the design, and material selection (ISO 16903:2015) |
| DIN EN ISO 16903 E : 2015 | PETROLEUM AND NATURAL GAS INDUSTRIES - CHARACTERISTICS OF LNG, INFLUENCING THE DESIGN AND MATERIAL SELECTION (ISO 16903:2015) |
| PD ISO/TR 17177:2015 | Petroleum and natural gas industries. Guidelines for the marine interfaces of hybrid LNG terminals |
| BS EN ISO 28460:2010 | Petroleum and natural gas industries. Installation and equipment for liquefied natural gas. Ship-to-shore interface and port operations |
| NORSOK P 002 : REV 1 AC 2017 | PROCESS SYSTEM DESIGN |
| I.S. EN 1474-1:2008 | INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN AND TESTING OF MARINE TRANSFER SYSTEMS - PART 1: DESIGN AND TESTING OF TRANSFER ARMS |
| I.S. EN 1474-2:2008 | INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN AND TESTING OF MARINE TRANSFER SYSTEMS - PART 2: DESIGN AND TESTING OF TRANSFER HOSES |
| DIN EN 1594:2013-12 | GAS INFRASTRUCTURE - PIPELINES FOR MAXIMUM OPERATING PRESSURE OVER 16 BAR - FUNCTIONAL REQUIREMENTS |
| I.S. EN 1594:2013 | GAS INFRASTRUCTURE - PIPELINES FOR MAXIMUM OPERATING PRESSURE OVER 16 BAR - FUNCTIONAL REQUIREMENTS |
| DIN EN 13645:2002-07 | INSTALLATIONS AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN OF ONSHORE INSTALLATIONS WITH A STORAGE CAPACITY BETWEEN 5 T AND 200 T |
| PREN 1594 : DRAFT 2013 | GAS INFRASTRUCTURE - PIPELINES FOR MAXIMUM OPERATING PRESSURE OVER 16 BAR - FUNCTIONAL REQUIREMENTS |
| PD ISO/TS 16901:2015 | Guidance on performing risk assessment in the design of onshore LNG installations including the ship/shore interface |
| DIN EN 1474-2:2009-02 | Installation and equipment for liquefied natural gas - Design and testing of marine transfer systems - Part 2: Design and testing of transfer hoses |
| 13/30276429 DC : 0 | BS EN ISO 16903 - CHARACTERISTICS OF LNG INFLUENCING DESIGN AND MATERIAL SELECTION |
| BS EN 1474-2:2008 | Installation and equipment for liquefied natural gas. Design and testing of marine transfer systems Design and testing of transfer hoses |
| ISO 16903:2015 | Petroleum and natural gas industries Characteristics of LNG, influencing the design, and material selection |
| UNI EN ISO 28460 : 2011 | PETROLEUM AND NATURAL GAS INDUSTRIES - INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - SHIP-TO-SHORE INTERFACE AND PORT OPERATIONS |
| DIN EN 1474-3:2009-02 | INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN AND TESTING OF MARINE TRANSFER SYSTEMS - PART 3: OFFSHORE TRANSFER SYSTEMS |
| I.S. EN 1474-3:2008 | INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN AND TESTING OF MARINE TRANSFER SYSTEMS - PART 3: OFFSHORE TRANSFER SYSTEMS |
| UNI EN 1474-2 : 2009 | INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN AND TESTING OF MARINE TRANSFER SYSTEMS - PART 2: DESIGN AND TESTING OF TRANSFER HOSES |
| API 2000 : 2014 | VENTING ATMOSPHERIC AND LOW-PRESSURE STORAGE TANKS |
| BS EN 1594:2013 | Gas infrastructure. Pipelines for maximum operating pressure over 16 bar. Functional requirements |
| ISO 28300:2008 | Petroleum, petrochemical and natural gas industries — Venting of atmospheric and low-pressure storage tanks |
| EEMUA 207 : 2009 | DOUBLE CONCRETE TANKS FOR LIQUEFIED GAS - GUIDE TO DESIGN, CONSTRUCTION AND OPERATION |
| EN 1474-2:2008 | Installation and equipment for liquefied natural gas - Design and testing of marine transfer systems - Part 2: Design and testing of transfer hoses |
| EN 1474-1:2008 | Installation and equipment for liquefied natural gas - Design and testing of marine transfer systems - Part 1: Design and testing of transfer arms |
| UNI EN 1594 : 2013 | GAS INFRASTRUCTURE - PIPELINES FOR MAXIMUM OPERATING PRESSURE OVER 16 BAR - FUNCTIONAL REQUIREMENTS |
| UNI EN ISO 28300 : 2009 | PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - VENTING OF ATMOSPHERIC AND LOW-PRESSURE STORAGE TANKS |
| I.S. EN ISO 16903:2015 | PETROLEUM AND NATURAL GAS INDUSTRIES - CHARACTERISTICS OF LNG, INFLUENCING THE DESIGN, AND MATERIAL SELECTION (ISO 16903:2015) |
| DIN EN 1474-1:2009-03 | INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN AND TESTING OF MARINE TRANSFER SYSTEMS - PART 1: DESIGN AND TESTING OF TRANSFER ARMS |
| PD ISO/TS 18683:2015 | Guidelines for systems and installations for supply of LNG as fuel to ships |
| 99/710167 DC : DRAFT JUNE 1999 | DRAFT BS: EN 13645 INSTALLATIONS AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN OF ONSHORE INSTALLATIONS WITH A STORAGE CAPACITY BETWEEN 5 T AND 200 T |
| BS EN 1474-1:2008 | Installation and equipment for liquefied natural gas. Design and testing of marine transfer systems Design and testing of transfer arms |
| BS EN ISO 16903:2015 | Petroleum and natural gas industries. Characteristics of LNG, influencing the design, and material selection |
| 09/30194936 DC : DRAFT JAN 2009 | BS EN ISO 28460 - PETROLEUM AND NATURAL GAS INDUSTRIES - INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - SHIP-TO-SHORE INTERFACE AND PORT OPERATIONS |
| UNI EN 1474-3 : 2009 | INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN AND TESTING OF MARINE TRANSFER SYSTEMS - PART 3: OFFSHORE TRANSFER SYSTEMS |
| UNE-EN ISO 16903:2016 | Petroleum and natural gas industries - Characteristics of LNG, influencing the design, and material selection (ISO 16903:2015) |
| I.S. EN ISO 28460:2010 | PETROLEUM AND NATURAL GAS INDUSTRIES - INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - SHIP-TO-SHORE INTERFACE AND PORT OPERATIONS |
| ISO/TS 16901:2015 | Guidance on performing risk assessment in the design of onshore LNG installations including the ship/shore interface |
| BS EN ISO 28300:2008 | Petroleum, petrochemical and natural gas industries. Venting of atmospheric and low-pressure storage tanks |
| BS EN 13645:2002 | Installations and equipment for liquefied natural gas. Design of onshore installations with a storage capacity between 5 t and 200 t |
| UNE-EN ISO 28300:2012 | Petroleum, petrochemical and natural gas industries - Venting of atmospheric and low-pressure storage tanks (ISO 28300:2008) |
| BS EN 14620-1:2006 | Design and manufacture of site built, vertical, cylindrical, flat-bottomed steel tanks for the storage of refrigerated, liquefied gases with operating temperatures between 0°C and -165°C General |
| 12/30210113 DC : 0 | BS EN ISO 28300 - PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - VENTING OF ATMOSPHERIC AND LOW-PRESSURE STORAGE TANKS |
| UNE-EN 1594:2014 | Gas infrastructure - Pipelines for maximum operating pressure over 16 bar - Functional requirements |
| EN ISO 28460:2010 | Petroleum and natural gas industries - Installation and equipment for liquefied natural gas - Ship-to-shore interface and port operations (ISO 28460:2010) |
| EN 1474 : 1997 | INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN AND TESTING OF LOADING/UNLOADING ARMS |
| EN 14620-1:2006 | Design and manufacture of site built, vertical, cylindrical, flat-bottomed steel tanks for the storage of refrigerated, liquefied gases with operating temperatures between 0 °C and -165 °C - Part 1: General |
| EN 1594:2013 | Gas infrastructure - Pipelines for maximum operating pressure over 16 bar - Functional requirements |
| EN 1474-3:2008 | Installation and equipment for liquefied natural gas - Design and testing of marine transfer systems - Part 3: Offshore transfer systems |
| EN 13645:2001 | Installations and equipment for liquefied natural gas - Design of onshore installations with a storage capacity between 5 t and 200 t |
| EN 1532 : 1997 | INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - SHIP TO SHORE INTERFACE |
| I.S. EN 1532:1997 | INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - SHIP TO SHORE INTERFACE |
| 06/30158813 DC : 0 | BS EN 1474-3 - INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN AND TESTING OF MARINE TRANSFER SYSTEMS - PART 3: OFFSHORE TRANSFER SYSTEMS |
| 13/30271116 DC : 0 | BS EN 1594 - GAS INFRASTRUCTURE - PIPELINES FOR MAXIMUM OPERATING PRESSURE OVER 16 BAR - FUNCTIONAL REQUIREMENTS |
| DIN EN ISO 28300:2008-11 | PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - VENTING OF ATMOSPHERIC AND LOW-PRESSURE STORAGE TANKS |
| ISO/TR 17177:2015 | Petroleum and natural gas industries Guidelines for the marine interfaces of hybrid LNG terminals |
| ISO/TS 18683:2015 | Guidelines for systems and installations for supply of LNG as fuel to ships |
| DIN EN ISO 28300:2012-02 (Draft) | PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - VENTING OF ATMOSPHERIC AND LOW-PRESSURE STORAGE TANKS |
| ISO 28460:2010 | Petroleum and natural gas industries Installation and equipment for liquefied natural gas Ship-to-shore interface and port operations |
| EN ISO 28300:2008/AC:2009 | Petroleum, petrochemical and natural gas industries - Venting of atmospheric and low-pressure storage tanks (ISO 28300:2008/Cor 1:2009) |
| ISO 9906:2012 | Rotodynamic pumps — Hydraulic performance acceptance tests — Grades 1, 2 and 3 |
| EN 1127-1:2011 | Explosive atmospheres - Explosion prevention and protection - Part 1: Basic concepts and methodology |
| ISO 17636-1:2013 | Non-destructive testing of welds — Radiographic testing — Part 1: X- and gamma-ray techniques with film |
| IEC 60079-1:2014 RLV | Explosive atmospheres - Part 1: Equipment protection by flameproof enclosures "d" |
| IEC 60364-5-54:2011 | Low-voltage electrical installations - Part 5-54: Selection and erection of electrical equipment - Earthing arrangements and protective conductors |
| EN 13766:2010 | Thermoplastic multi-layer (non-vulcanized) hoses and hose assemblies for the transfer of liquid petroleum gas and liquefied natural gas - Specification |
| EN 1514-1:1997 | Flanges and their joints - Dimensions of gaskets for PN-designated flanges - Part 1: Non-metallic flat gaskets with or without inserts |
| EN 60079-26:2015 | Explosive atmospheres - Part 26: Equipment with Equipment Protection Level (EPL) Ga |
| EN 12560-6:2003 | Flanges and their joints - Gaskets for Class-designated flanges - Part 6: Covered serrated metal gaskets for use with steel flanges |
| IMO IA116 : 2012 | MARITIME SECURITY GUIDE AND THE ISPS CODE |
| EN 12162:2001+A1:2009 | Liquid pumps - Safety requirements - Procedure for hydrostatic testing |
| CFR 10(PTS0-199) : JAN 87 | ENERGY - NUCLEAR REGULATORY COMMISSION |
| EN 60079-27:2008 | Explosive atmospheres - Part 27: Fieldbus intrinsically safe concept (FISCO) |
| ISO 15664:2001 | Acoustics — Noise control design procedures for open plant |
| NFPA 921 : 2017 | GUIDE FOR FIRE AND EXPLOSION INVESTIGATIONS |
| EN 12560-1:2001 | Flanges and their joints - Gaskets for Class-designated flanges - Part 1: Non-metallic flat gaskets with or without inserts |
| EN ISO 10456:2007/AC:2009 | BUILDING MATERIALS AND PRODUCTS - HYGROTHERMAL PROPERTIES - TABULATED DESIGN VALUES AND PROCEDURES FOR DETERMINING DECLARED AND DESIGN THERMAL VALUES |
| EN 12560-3:2001 | Flanges and their joints - Gaskets for Class-designated flanges - Part 3: Non-metallic PTFE envelope gaskets |
| EN 61508-1:2010 | Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 1: General requirements |
| EN 60079-1:2014 | Explosive atmospheres - Part 1: Equipment protection by flameproof enclosures "d" |
| EN ISO 3452-1:2013 | Non-destructive testing - Penetrant testing - Part 1: General principles (ISO 3452-1:2013, Corrected version 2014-05-01) |
| EN 60079-10-1:2015 | Explosive atmospheres - Part 10-1: Classification of areas - Explosive gas atmospheres |
| EN 12560-2:2013 | Flanges and their joints - Dimensions of gaskets for Class-designated flanges - Part 2: Spiral wound gaskets for use with steel flanges |
| ISO 5199:2002 | Technical specifications for centrifugal pumps — Class II |
| ISO 9712:2012 | Non-destructive testing Qualification and certification of NDT personnel |
| EN 60079-29-1:2016 | Explosive atmospheres - Part 29-1: Gas detectors - Performance requirements of detectors for flammable gases |
| IEC 60079-19:2010+AMD1:2015 CSV | Explosive atmospheres - Part 19: Equipment repair, overhaul and reclamation |
| EN 60079-0:2012/A11:2013 | EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS (IEC 60079-0:2011, MODIFIED) |
| EN 1759-1:2004 | Flanges and their joint - Circular flanges for pipes, valves, fittings and accessories, Class designated - Part 1: Steel flanges, NPS 1/2 to 24 |
| EN ISO 1461:2009 | Hot dip galvanized coatings on fabricated iron and steel articles - Specifications and test methods (ISO 1461:2009) |
| IEC 60079-17:2013 | Explosive atmospheres - Part 17: Electrical installations inspection and maintenance |
| EN 12483:1999 | Liquid pumps - Pump units with frequency inverters - Guarantee and compatibility tests |
| EN 60079-15:2010 | Explosive atmospheres - Part 15: Equipment protection by type of protection "n" |
| EN 12065 : 1997 | INSTALLATIONS AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - TESTING OF FOAM CONCENTRATES DESIGNED FOR GENERATION OF MEDIUM AND HIGH EXPANSION FOAM AND OF EXTINGUISHING POWDERS USED ON LIQUEFIED NATURAL GAS FIRES |
| EN 60079-19:2011/A1:2015 | EXPLOSIVE ATMOSPHERES - PART 19: EQUIPMENT REPAIR, OVERHAUL AND RECLAMATION (IEC 60079-19:2010) |
| EN 12560-4:2001 | Flanges and their joints - Gaskets for Class-designated flantes - Part 4: Corrugated, flat or grooved metallic and filled metallic gaskets for use with steel flanges |
| EN 1994-1-1:2004/AC:2009 | EUROCODE 4: DESIGN OF COMPOSITE STEEL AND CONCRETE STRUCTURES - PART 1-1: GENERAL RULES AND RULES FOR BUILDINGS |
| VDI 2055:1994-07 | Thermal insulation for heated and refrigerated industrial and domestic installations - Calculations, guarantees, measuring and testing methods, quality assurance, supply conditions |
| IEC 60079-18:2014 RLV | Explosive atmospheres - Part 18: Equipment protection by encapsulation “m” |
| HD 60364-5-54:2011/A11:2017 | LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 5-54: SELECTION AND ERECTION OF ELECTRICAL EQUIPMENT - EARTHING ARRANGEMENTS AND PROTECTIVE CONDUCTORS |
| EN 60079-10-2:2015 | Explosive atmospheres - Part 10-2: Classification of areas - Explosive dust atmospheres |
| EN 823:2013 | Thermal insulating products for building applications - Determination of thickness |
| ISO 9606-1:2012 | Qualification testing of welders — Fusion welding — Part 1: Steels |
| EN ISO 5199 : 2002 | TECHNICAL SPECIFICATIONS FOR CENTRIFUGAL PUMPS - CLASS 2 |
| IEC 60079-10-1:2015 | Explosive atmospheres - Part 10-1: Classification of areas - Explosive gas atmospheres |
| ISO 1461:2009 | Hot dip galvanized coatings on fabricated iron and steel articles — Specifications and test methods |
| ISO 16903:2015 | Petroleum and natural gas industries Characteristics of LNG, influencing the design, and material selection |
| EN 60079-6:2015 | Explosive atmospheres - Part 6: Equipment protection by liquid immersion "o" |
| EN 13645:2001 | Installations and equipment for liquefied natural gas - Design of onshore installations with a storage capacity between 5 t and 200 t |
| BS 1722-10:2006 | Fences Specification for anti-intruder fences in chain link and welded mesh |
| ISO 12100:2010 | Safety of machinery — General principles for design — Risk assessment and risk reduction |
| IEC TR 60079-16:1990 | Electrical apparatus for explosive gas atmospheres. Part 16: Artificial ventilation for the protection of analyser(s) houses |
| IEC 60079-5:2015 RLV | Explosive atmospheres - Part 5: Equipment protection by powder filling "q" |
| EN ISO 9712:2012 | Non-destructive testing - Qualification and certification of NDT personnel (ISO 9712:2012) |
| ISO 17640:2017 | Non-destructive testing of welds Ultrasonic testing Techniques, testing levels, and assessment |
| EN ISO 13709:2009 | Centrifugal pumps for petroleum, petrochemical and natural gas industries (ISO 13709:2009) |
| EN 1994-1-2:2005/A1:2014 | EUROCODE 4 - DESIGN OF COMPOSITE STEEL AND CONCRETE STRUCTURES - PART 1-2: GENERAL RULES - STRUCTURAL FIRE DESIGN |
| EN 1991-1-2:2002/AC:2013 | EUROCODE 1: ACTIONS ON STRUCTURES - PART 1-2: GENERAL ACTIONS - ACTIONS ON STRUCTURES EXPOSED TO FIRE |
| ISO 3452-1:2013 | Non-destructive testing Penetrant testing Part 1: General principles |
| ISO 15614-1:2017 | Specification and qualification of welding procedures for metallic materials — Welding procedure test — Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys |
| EN 60079-11:2012 | Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i" |
| ISO 28460:2010 | Petroleum and natural gas industries Installation and equipment for liquefied natural gas Ship-to-shore interface and port operations |
| IEC 60079-11:2011 | Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i" |
| ISO 15609-1:2004 | Specification and qualification of welding procedures for metallic materials Welding procedure specification Part 1: Arc welding |
| EN ISO 1460 : 1994 | METALLIC COATINGS - HOT DIP GALVANIZED COATINGS ON FERROUS MATERIALS - GRAVIMETRIC DETERMINATION OF THE MASS PER UNIT AREA |
| EN ISO 17637:2016 | Non-destructive testing of welds - Visual testing of fusion-welded joints (ISO 17637:2016) |
| IEC 60079-27:2008 | Explosive atmospheres - Part 27: Fieldbus intrinsically safe concept (FISCO) |
| EN ISO 16903:2015 | Petroleum and natural gas industries - Characteristics of LNG, influencing the design, and material selection (ISO 16903:2015) |
| EN 809 : 1998 COR 2010 | PUMPS AND PUMP UNITS FOR LIQUIDS - COMMON SAFETY REQUIREMENTS |
| EN 60079-25:2010/AC:2013 | EXPLOSIVE ATMOSPHERES - PART 25: INTRINSICALLY SAFE ELECTRICAL SYSTEMS (IEC 60079-25:2010) |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| EN 12308 : 1998 | INSTALLATIONS AND EQUIPMENT FOR LNG - SUITABILITY TESTING OF GASKETS DESIGNED FOR FLANGED JOINTS USED ON LNG PIPING |
| ISO 17636-2:2013 | Non-destructive testing of welds — Radiographic testing — Part 2: X- and gamma-ray techniques with digital detectors |
| EN 1992-1-2:2004/AC:2008 | EUROCODE 2: DESIGN OF CONCRETE STRUCTURES - PART 1-2: GENERAL RULES - STRUCTURAL FIRE DESIGN |
| IEC 60079-25:2010 | Explosive atmospheres - Part 25: Intrinsically safe electrical systems |
| ISO 12241:2008 | Thermal insulation for building equipment and industrial installations Calculation rules |
| IEC 60079-6:2015 | Explosive atmospheres - Part 6: Equipment protection by liquid immersion "o" |
| IEC 60079-0:2011 | Explosive atmospheres - Part 0: Equipment - General requirements |
| ISO 10456:2007 | Building materials and products — Hygrothermal properties — Tabulated design values and procedures for determining declared and design thermal values |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| EN ISO 10497:2010 | Testing of valves - Fire type-testing requirements (ISO 10497:2010) |
| IEC 60079-14:2013 | Explosive atmospheres - Part 14: Electrical installations design, selection and erection |
| EN ISO 12241:2008 | Thermal insulation for building equipment and industrial installations - Calculation rules (ISO 12241:2008) |
| ISO 17637:2016 | Non-destructive testing of welds Visual testing of fusion-welded joints |
| EN ISO 15609-1:2004 | Specification and qualification of welding procedures for metallic materials - Welding procedure specification - Part 1: Arc welding (ISO 15609-1:2004) |
| EN 60079-20-1:2010 | Explosive atmospheres - Part 20-1: Material characteristics for gas and vapour classification - Test methods and data |
| EN ISO 12100:2010 | Safety of machinery - General principles for design - Risk assessment and risk reduction (ISO 12100:2010) |
| EN ISO 17636-2:2013 | Non-destructive testing of welds - Radiographic testing - Part 2: X- and gamma-ray techniques with digital detectors (ISO 17636-2:2013) |
| EN ISO 9906:2012 | Rotodynamic pumps - Hydraulic performance acceptance tests - Grades 1, 2 and 3 (ISO 9906:2012) |
| EN 60079-14:2014/AC:2016 | EXPLOSIVE ATMOSPHERES - PART 14: ELECTRICAL INSTALLATIONS DESIGN, SELECTION AND ERECTION (IEC 60079-14:2013/COR1:2016) |
| ISO 13709:2009 | Centrifugal pumps for petroleum, petrochemical and natural gas industries |
| IP 15 : 2015 | PETROLEUM PRODUCTS - DETERMINATION OF POUR POINT |
| EN ISO 28460:2010 | Petroleum and natural gas industries - Installation and equipment for liquefied natural gas - Ship-to-shore interface and port operations (ISO 28460:2010) |
| EN 60079-5:2015 | Explosive atmospheres - Part 5: Equipment protection by powder filling "q" |
| ISO 10497:2010 | Testing of valves — Fire type-testing requirements |
| ISO/TS 16901:2015 | Guidance on performing risk assessment in the design of onshore LNG installations including the ship/shore interface |
| EN 60079-17:2014 | Explosive atmospheres - Part 17: Electrical installations inspection and maintenance |
| ISO 1460:1992 | Metallic coatings Hot dip galvanized coatings on ferrous materials Gravimetric determination of the mass per unit area |
| IEC 61508-1:2010 | Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 1: General requirements (see Functional Safety and IEC 61508) |
| EN 1992-1-1:2004/A1:2014 | EUROCODE 2: DESIGN OF CONCRETE STRUCTURES - PART 1-1: GENERAL RULES AND RULES FOR BUILDINGS |
| EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
| EN 12560-5:2001 | Flanges and their joints - Gaskets for Class-designated flanes - Part 5: Metallic ring joint gaskets for use with steel flanges |
| EN 12567:2000 | Industrial valves - Isolating valves for LNG - Specification for suitability and appropriate verification tests |
| EN 1993-1-2:2005/AC:2009 | EUROCODE 3: DESIGN OF STEEL STRUCTURES - PART 1-2: GENERAL RULES - STRUCTURAL FIRE DESIGN |
| EN 12434:2000/AC:2001 | CRYOGENIC VESSELS - CRYOGENIC FLEXIBLE HOSES |
| ISO 15607:2003 | Specification and qualification of welding procedures for metallic materials General rules |
| EN 1998-1:2004/A1:2013 | EUROCODE 8: DESIGN OF STRUCTURES FOR EARTHQUAKE RESISTANCE - PART 1: GENERAL RULES, SEISMIC ACTIONS AND RULES FOR BUILDINGS |
| EN ISO 17636-1:2013 | Non-destructive testing of welds - Radiographic testing - Part 1: X- and gamma-ray techniques with film (ISO 17636-1:2013) |
| EN ISO 9606-1:2017 | Qualification testing of welders - Fusion welding - Part 1: Steels (ISO 9606-1:2012 including Cor 1:2012 and Cor 2:2013) |
| EN 14620-1:2006 | Design and manufacture of site built, vertical, cylindrical, flat-bottomed steel tanks for the storage of refrigerated, liquefied gases with operating temperatures between 0 °C and -165 °C - Part 1: General |
| EN 60079-13:2017 | Explosive atmospheres - Part 13: Equipment protection by pressurized room "p" and artificially ventilated room "v" |
| API 2218 : 2013 | FIREPROOFING PRACTICES IN PETROLEUM AND PETROCHEMICAL PROCESSING PLANTS |
| IEC 60079-15:2010 | Explosive atmospheres - Part 15: Equipment protection by type of protection "n" |
| IEC 60079-13:2017 | Explosive atmospheres - Part 13: Equipment protection by pressurized room "p" and artificially ventilated room "v" |
| IEC 60079-26:2014 RLV | Explosive atmospheres - Part 26: Equipment with Equipment Protection Level (EPL) Ga |
| EN ISO 15607:2003 | Specification and qualification of welding procedures for metallic materials - General rules (ISO 15607:2003) |
| EN 60034-5:2001/A1:2007 | ROTATING ELECTRICAL MACHINES - PART 5: DEGREES OF PROTECTION PROVIDED BY THE INTEGRAL DESIGN OF ROTATING ELECTRICAL MACHINES (IP CODE) - CLASSIFICATION |
| EN 1993-1-1:2005/A1:2014 | EUROCODE 3: DESIGN OF STEEL STRUCTURES - PART 1-1: GENERAL RULES AND RULES FOR BUILDINGS |
| EN 1776:2015 | Gas infrastructure - Gas measuring systems - Functional requirements |
| EN 1998-5:2004 | EUROCODE 8: DESIGN OF STRUCTURES FOR EARTHQUAKE RESISTANCE - PART 5: FOUNDATIONS, RETAINING STRUCTURES AND GEOTECHNICAL ASPECTS |
| EN 60079-2:2014/AC:2015 | EXPLOSIVE ATMOSPHERES - PART 2: EQUIPMENT PROTECTION BY PRESSURIZED ENCLOSURE 'P' (IEC 60079-2:2014) |
| EN 12066 : 1997 | INSTALLATIONS AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - TESTING OF INSULATING LININGS FOR LIQUEFIED NATURAL GAS IMPOUNDING AREAS |
Sorry this product is not available in your region.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.