Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

EN 14944-1:2006

Withdrawn
Withdrawn

A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.

Influence of cementitious products on water intended for human consumption - Test methods - Part 1: Influence of factory made cementitious products on organoleptic parameters
Withdrawn date

31-10-2006

Published date

05-04-2006

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Principle
5 Reagents
6 Apparatus
7 Samples and test pieces
8 Pre-treatment of samples (curing, preconditioning and
   disinfection)
9 Test procedure
10 Determination of odour as TON and flavour as TFN
11 Determination of colour and turbidity
12 Expression of results
13 Test report
Annex A (normative) Additional procedures for testing
                      factory made pipes (cement mortar lined
                      and concrete)
Annex B (normative) Additional procedures for testing
                      factory made fittings (cement mortar
                      lined and concrete)
Annex C (normative) Additional procedures for testing
                      factory made storage systems (cement
                      mortar, cement mortar lined and
                      concrete)
Annex D (informative) Examples of typical test pieces
                      and test conditions as a function of
                      S/V ratio
Annex E (informative) Test arrangements for testing factory
                      made cementitious products
Annex F (normative) Additional procedures for testing
                      factory made cementitious products at
                      elevated temperature
Annex G (informative) Discrimination between porous and
                      non-porous coatings on factory made
                      products
Annex H (informative) Schematic description of the test
                      procedure
Bibliography

This European Standard specifies a method to determine the influence of factory made cementitious products on the odour, flavour, colour and turbidity of test waters after contact with the products.This European Standard is applicable to factory made cementitious products, e.g. cement mortar linings to metallic pipes, tanks, concrete pipes etc. intended to be used for the transport and storage of water for human consumption, including raw water used for the production of drinking water.

Committee
CEN/TC 164
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Withdrawn

PD CEN/TR 16950:2016 Ductile iron pipes, fittings and accessories. Sanitary characteristics and test methods
I.S. EN 16421:2014 INFLUENCE OF MATERIALS ON WATER FOR HUMAN CONSUMPTION - ENHANCEMENT OF MICROBIAL GROWTH (EMG)
UNE-EN 16421:2015 Influence of materials on water for human consumption - Enhancement of microbial growth (EMG)
12/30260010 DC : 0 BS EN 16421 - INFLUENCE OF MATERIALS ON WATER FOR HUMAN CONSUMPTION - ENHANCEMENT OF MICROBIAL GROWTH (EMG)
BS EN 16421:2014 Influence of materials on water for human consumption. Enhancement of microbial growth (EMG)
S.R. CEN/TR 16950:2016 DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - SANITARY CHARACTERISTICS AND TEST METHODS
CEN/TR 16950:2016 Ductile iron pipes, fittings and accessories - Sanitary characteristics and test methods
DIN EN 16421 E : 2015 INFLUENCE OF MATERIALS ON WATER FOR HUMAN CONSUMPTION - ENHANCEMENT OF MICROBIAL GROWTH (EMG)
EN 16421:2014 Influence of materials on water for human consumption - Enhancement of microbial growth (EMG)
DIN EN 16421:2015-05 INFLUENCE OF MATERIALS ON WATER FOR HUMAN CONSUMPTION - ENHANCEMENT OF MICROBIAL GROWTH (EMG)
UNI EN 16421 : 2015 INFLUENCE OF MATERIALS ON WATER FOR HUMAN CONSUMPTION - ENHANCEMENT OF MICROBIAL GROWTH (EMG)

ISO 6058:1984 Water quality — Determination of calcium content — EDTA titrimetric method
EN 27888 : 1993 WATER QUALITY - DETERMINATION OF ELECTRICAL CONDUCTIVITY
EN ISO 7393-1 : 2000 WATER QUALITY - DETERMINATION OF FREE CHLORINE AND TOTAL CHLORINE - PART 1: TITRIMETRIC METHOD USING N,N-DIETHYL-1,4-PHENYLENEDIAMINE
ISO 16264:2002 Water quality — Determination of soluble silicates by flow analysis (FIA and CFA) and photometric detection
ISO 16132:2016 Ductile iron pipes and fittings — Seal coats for cement mortar linings
EN ISO 7027 : 1999 WATER QUALITY - DETERMINATION OF TURBIDITY
EN 1015-11 : 1999 AMD 1 2006 METHODS OF TEST FOR MORTAR FOR MASONRY - PART 11: DETERMINATION OF FLEXURAL AND COMPRESSIVE STRENGTH OF HARDENED MORTAR
EN ISO 16264 : 2004 WATER QUALITY - DETERMINATION OF SOLUBLE SILICATES BY FLOW ANALYSIS (FIA AND CFA) AND PHOTOMETRIC DETECTION
EN 1015-2:1998/A1:2006 METHODS OF TEST FOR MORTAR FOR MASONRY - PART 2: BULK SAMPLING OF MORTARS AND PREPARATION OF TEST MORTARS
EN 196-1:2016 Methods of testing cement - Part 1: Determination of strength
EN 1622:2006 Water quality - Determination of the threshold odour number (TON) and threshold flavour number (TFN)
ISO 9963-2:1994 Water quality Determination of alkalinity Part 2: Determination of carbonate alkalinity
EN 12390-1:2012 TESTING HARDENED CONCRETE - PART 1: SHAPE, DIMENSIONS AND OTHER REQUIREMENTS FOR SPECIMENS AND MOULDS
ISO 7887:2011 Water quality — Examination and determination of colour
EN 12390-2:2009 Testing hardened concrete - Part 2: Making and curing specimens for strength tests
EN ISO 7887:2011 Water quality - Examination and determination of colour (ISO 7887:2011)
ISO 3696:1987 Water for analytical laboratory use — Specification and test methods
EN 12350-1:2009 Testing fresh concrete - Part 1: Sampling
EN ISO 3696:1995 Water for analytical laboratory use - Specification and test methods (ISO 3696:1987)
EN ISO 9963-2 : 1995 WATER QUALITY - DETERMINATION OF ALKALINITY - PART 2: DETERMINATION OF CARBONATE ALKALINITY
ISO 7393-2:1985 Water quality Determination of free chlorine and total chlorine Part 2: Colorimetric method using N,N-diethyl-1,4-phenylenediamine, for routine control purposes
ISO 10523:2008 Water quality — Determination of pH
ISO 5492:2008 Sensory analysis — Vocabulary
EN 10088-1:2014 Stainless steels - Part 1: List of stainless steels
ISO 7027:1999 Water quality Determination of turbidity

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more