Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

EN 15167-2:2006

Current
Current

The latest, up-to-date edition.

Ground granulated blast furnace slag for use in concrete, mortar and grout - Part 2: Conformity evaluation
Published date

02-08-2006

Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Tasks for the manufacturer
  4.1 Factory production control
      4.1.1 Concept
      4.1.2 Works' quality manual
      4.1.3 Management systems
      4.1.4 System of documentation
  4.2 Internal quality control
      4.2.1 Process control
      4.2.2 Measuring and testing
      4.2.3 Handling, storage, packaging and delivery
  4.3 Autocontrol testing of samples
      4.3.1 Sampling and testing
      4.3.2 Corrective action
      4.3.3 Measuring and test equipment for autocontrol testing
      4.3.4 Quality records
5 Tasks for the certification body
  5.1 General
  5.2 Surveillance, assessment and acceptance of the production
      control
      5.2.1 Inspection tasks
      5.2.2 Frequency of inspections
      5.2.3 Reports
  5.3 Evaluation of the results of autocontrol testing of samples
      5.3.1 Evaluation tasks
      5.3.2 Number and timing of evaluations
      5.3.3 Control period
      5.3.4 Evaluation of test results
      5.3.5 Reports
  5.4 Audit testing of samples taken at the factory/depot and
      initial type testing
      5.4.1 Sampling
      5.4.2 Number of samples
      5.4.3 Properties and test methods
      5.4.4 Testing
      5.4.5 Evaluation of test results
      5.4.6 Reports
      5.4.7 Proficiency testing
  5.5 Initial inspection of the factory and the production control
      5.5.1 Inspection of a new factory
      5.5.2 Inspection of an existing factory
      5.5.3 Criteria for the assessment of the production equipment
      5.5.4 Criteria for the assessment of laboratories
      5.5.5 Reports
  5.6 Evaluation of test results during the initial period
      5.6.1 Initial period
      5.6.2 Evaluation of test results
      5.6.3 Reports
6 Actions in the event of non-conformity
  6.1 Actions to be taken by the manufacturer
  6.2 Actions to be taken by the certification body
      6.2.1 Following surveillance, assessment and acceptance of
            the production control and evaluation of the results
            of autocontrol testing
      6.2.2 Following evaluation of the results of the audit
            testing of samples taken at the factory/depot
7 Procedure for third party certification of conformity
8 Certificates of conformity and conformity mark
9 Requirements for dispatching centres
  9.1 General requirements
  9.2 Tasks for the intermediary
      9.2.1 Measures to maintain the ground granulated blastfurnace
            slag quality
      9.2.2 Confirmation autocontrol testing of samples taken at the
            dispatching centre
  9.3 Tasks for the third party
      9.3.1 Surveillance, assessment and acceptance of the measures
            to maintain the ground granulated blastfurnace slag
            quality and of the confirmation autocontrol
      9.3.2 Audit testing of samples taken at the dispatching centre
      9.3.3 Decisions to be taken
Annex A (normative) - Evaluation of the representativeness and the
                      accuracy of the 28 day activity index test
                      results
        A.1 General
        A.2 Sets of results considered
        A.3 Evaluation procedure
            A.3.1 Introduction
            A.3.2 Symbols
            A.3.3 Evaluation of whether set A and set B belong to the
                  same population (sampling error check)
            A.3.4 Comparison between set B and set C in order to check
                  the accuracy of the autocontrol testing (testing
                  error check)
Bibliography

This European Standard specifies the scheme for the evaluation of conformity of ground granulated blastfurnace slag according to EN 15167-1.The European Standard provides technical rules for the production control by the manufacturer, including autocontrol testing of samples. It also provides rules for actions to be followed in the event of non-conformity, the procedure for the certification of conformity and requirements for dispatching centres.

DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Current

EEMUA 207 : 2009 DOUBLE CONCRETE TANKS FOR LIQUEFIED GAS - GUIDE TO DESIGN, CONSTRUCTION AND OPERATION
UNI EN 15167-1 : 2006 GROUND GRANULATED BLAST FURNACE SLAG FOR USE IN CONCRETE, MORTAR AND GROUT - PART 1: DEFINITIONS, SPECIFICATIONS AND CONFORMITY CRITERIA
EN 15167-1:2006 Ground granulated blast furnace slag for use in concrete, mortar and grout - Part 1: Definitions, specifications and conformity criteria
BS EN 15167-1:2006 Ground granulated blast furnace slag for use in concrete, mortar and grout Definitions, specifications and conformity criteria

EN 196-7:2007 Methods of testing cement - Part 7: Methods of taking and preparing samples of cement
ISO 2854:1976 Statistical interpretation of data — Techniques of estimation and tests relating to means and variances
89/106/EEC : 1988 COUNCIL DIRECTIVE OF 21 DECEMBER 1988 ON THE APPROXIMATION OF LAWS, REGULATIONS AND ADMINISTRATIVE PROVISIONS OF THE MEMBER STATES RELATING TO CONSTRUCTION PRODUCTS
EN 45011:1998 General requirements for bodies operating product certification systems (ISO/IEC Guide 65:1996)
EN 45011 : 1998 GENERAL REQUIREMENTS FOR BODIES OPERATING PRODUCT CERTIFICATION SYSTEMS
EN 196-1:2016 Methods of testing cement - Part 1: Determination of strength
EN ISO 9001:2015 Quality management systems - Requirements (ISO 9001:2015)
EN 45020:2006 Standardization and related activities - General vocabulary (ISO/IEC Guide 2:2004)
ISO 9001:2015 Quality management systems — Requirements
EN 15167-1:2006 Ground granulated blast furnace slag for use in concrete, mortar and grout - Part 1: Definitions, specifications and conformity criteria
ISO 9000:2015 Quality management systems — Fundamentals and vocabulary
ISO/IEC Guide 2:2004 Standardization and related activities General vocabulary
ISO/IEC Guide 65:1996 General requirements for bodies operating product certification systems
EN 45020 : 2006 STANDARDIZATION AND RELATED ACTIVITIES - GENERAL VOCABULARY
EN ISO 9000:2015 Quality management systems - Fundamentals and vocabulary (ISO 9000:2015)

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more