Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

EN 1519-1:1999

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polyethylene (PE) - Part 1: Specifications for pipes, fittings and the system
Superseded date

04-05-2019

Published date

21-07-1999

Foreword
1 Scope
2 Normative references
3 Definitions, symbols and abbreviations
   3.1 Definitions
   3.2 Symbols
   3.3 Abbreviations
4 Material
   4.1 PE-compound
   4.2 Reprocessable and recyclable material
   4.3 Melt mass-flow rate
   4.4 Fusion compatibility
   4.5 Thermal stability
   4.6 Sealing ring retaining means
   4.7 Fire behaviour
5 General characteristics
   5.1 Appearance
   5.2 Colour
6 Geometrical characteristics
   6.1 General
   6.2 Dimensions of pipes
   6.3 Dimensions of fittings
   6.4 Dimensions of sockets and pipe ends
   6.5 Types of fittings
7 Physical characteristics
   7.1 Physical characteristics of pipes
   7.2 Physical characteristics of fittings
8 Performance requirements
9 Requirements for application area "BD"
   9.1 General
   9.2 Material characteristics
   9.3 Mechanical characteristics
10 Sealing rings
11 Marking
   11.1 General
   11.2 Minimum required marking of pipes
   11.3 Minimum required marking of fittings
12 Installation of piping systems
Annex A (informative) General characteristics of PE pipes
        and fittings
   A.1 General
   A.2 Material characteristics
   A.3 Ring stiffness
   A.4 Chemical resistance
Bibliography

This standard specifies the requirements for pipes, fittings and the system of polyethylene (PE) solid-wall piping systems in the field of soil and waste discharge - inside buildings (marked with "B") and - for both inside buildings and buried in ground within the building structure (marked with "BD"). It also specifies the test parameters for the test methods referred to in this standard.

Committee
CEN/TC 155
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Superseded
SupersededBy

BS EN 1519-1:2000 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Polyethylene (PE) Specifications for pipes, fittings and the system
DD ENV 13801:2001 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Thermoplastics. Recommended practice for installation
ISO 7682:2003 Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings Acrylonitrile-butadiene-styrene (ABS)
05/30132479 DC : DRAFT MAY 2005 EN 1123-2 - PIPES AND FITTINGS OF LONGITUDINAL WELDED HOT-DIP GALVANIZED STEEL PIPES WITH SPIGOT AND SOCKET FOR WASTE WATER SYSTEMS - PART 2: DIMENSIONS
EN 1123-3:2004 Pipes and fittings of longitudinally welded hot-dip galvanized steel pipes with spigot and socket for waste water systems - Part 3: Dimensions and special requirements for vacuum drainage systems and for drainage systems in ship-building
EN 1123-2:2006+A1:2007 Pipes and fittings of longitudinally welded hot-dip galvanized steel tube with spigot and socket for waste water systems - Part 2: Dimensions
EN 12666-1:2005+A1:2011 Plastics piping systems for non-pressure underground drainage and sewerage - Polyethylene (PE) - Part 1: Specifications for pipes, fittings and the system
CEN/TR 13801:2014 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Thermoplastics - Recommended practice for installation
ENV 1519-2:2001 Plastics piping systems for soil and waste discharge (low and high temperature) within the building stucture - Polyethylene (PE) - Part 2: Guidance for the assessment of conformity
07/30165577 DC : 0 BS EN 1852-1 - PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - POLYPROPYLENE (PP) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM
UNI CEN/TS 1519-2 : 2012 PLASTIC PIPING SYSTEMS FOR SOIL AND WASTE DISCHARGE (LOW AND HIGH TEMPERATURE) WITHIN THE BUILDING STRUCTURE - POLYETHYLEN (PE) - PART 2: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY
DD ENV 1451-2:2001 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Polypropylene (PP) Guidance for the assessment of conformity
ISO 7675:2003 Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings Chlorinated poly(vinyl chloride) (PVC-C)
S.R. CEN/TR 13801:2014 PLASTICS PIPING SYSTEMS FOR SOIL AND WASTE DISCHARGE (LOW AND HIGH TEMPERATURE) WITHIN THE BUILDING STRUCTURE - THERMOPLASTICS - RECOMMENDED PRACTICE FOR INSTALLATION
ISO/TS 7024:2005 Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings — Thermoplastics — Recommended practice for installation
DIN EN 1366-3:2009-07 Fire resistance tests for service installations - Part 3: Penetration seals
DIN EN 1124-3:2009-02 PIPES AND FITTINGS OF LONGITUDINALLY WELDED STAINLESS STEEL PIPES WITH SPIGOT AND SOCKET FOR WASTE WATER SYSTEMS - PART 3: SYSTEM X - DIMENSIONS
DIN EN 1123-3:2005-02 Pipes and fittings of longitudinally welded hot-dip galvanized steel pipes with spigot and socket for waste water systems - Part 3: Dimensions and special requirements for vacuum drainage systems and for drainage systems in shipbuilding
BS EN 12380:2002 Air admittance valves for drainage systems. Requirements, test methods and evaluation of conformity
CEN/TS 1519-2:2012 Plastic piping systems for soil and waste discharge (low and high temperature) within the building structure - Polyethylen (PE) - Part 2: Guidance for the assessment of conformity
I.S. EN 1123-2:2006 PIPES AND FITTINGS OF LONGITUDINALLY WELDED HOT-DIP GALVANIZED STEEL TUBE WITH SPIGOT AND SOCKET FOR WASTE WATER SYSTEMS - PART 2: DIMENSIONS
I.S. EN 12666-1:2006 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - POLYETHYLENE (PE) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM
I.S. EN 1366-3:2009 FIRE RESISTANCE TESTS FOR SERVICE INSTALLATIONS - PART 3: PENETRATION SEALS
DD ENV 1566-2:2001 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Chlorinated poly(vinyl chloride) (PVC-C) Guidance for the assessment of conformity
PD CEN/TR 13801:2014 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Thermoplastics. Recommended practice for installation
DD ENV 1455-2:2001 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Acrylonitrile-butadiene- styrene (ABS) Guidance for the assessment of conformity
DD ENV 1519-2:2001 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Polyethylene (PE) Guidance for the assessment of conformity
ISO 7671:2003 Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings Polypropylene (PP)
S.R. CEN/TS 1519-2:2012 PLASTIC PIPING SYSTEMS FOR SOIL AND WASTE DISCHARGE (LOW AND HIGH TEMPERATURE) WITHIN THE BUILDING STRUCTURE - POLYETHYLEN (PE) - PART 2: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY
PREN 15012 : DRAFT 2014 PLASTICS PIPING SYSTEMS - BURIED AND ABOVE GROUND PIPING COMPONENTS FOR NON PRESSURE SOIL AND WASTE DISCHARGE WITHIN THE BUILDING STRUCTURE - REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR PIPES AND FITTINGS
DIN EN 12666-1:2011-11 Plastics piping systems for non-pressure underground drainage and sewerage - Polyethylene (PE) - Part 1: Specifications for pipes, fittings and the system (includes Amendment A1:2011)
DIN EN 1123-2:2007-12 PIPES AND FITTINGS OF LONGITUDINALLY WELDED HOT-DIP GALVANIZED STEEL TUBE WITH SPIGOT AND SOCKET FOR WASTE WATER SYSTEMS - PART 2: DIMENSIONS
BS EN 1123-2 : 2006 PIPES AND FITTINGS OF LONGITUDINALLY WELDED HOT-DIP GALVANIZED STEEL TUBE WITH SPIGOT AND SOCKET FOR WASTE WATER SYSTEMS - PART 2: DIMENSIONS
BS EN 1123-3:2004 Pipes and fittings of longitudinally welded hot-dip galvanized steel pipes with spigot and socket for waste water systems Dimensions and special requirements for vacuum drainage systems and for drainage systems in ship-building
UNI EN 12666-1 : 2011 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - POLYETHYLENE (PE) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM
ONORM EN 1366-3 : 2009 FIRE RESISTANCE TESTS FOR SERVICE INSTALLATIONS - PART 3: PENETRATION SEALS
PD CEN/TS 1519-2:2012 Plastic piping systems for soil and waste discharge (low and high temperature) within the building structure. Polyethylen (PE) Guidance for the assessment of conformity
02/121757 DC : DRAFT APR 2002 BS ISO 19220 - PLASTICS PIPING SYSTEMS FOR SOIL AND WASTE DISCHARGE (LOW AND HIGH TEMPERATURE) INSIDE BUILDINGS - STYRENE COPOLYMER BLENDS (SAN + PVC)
DD ENV 1565-2:2001 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Styrene copolymer blends (SAN + PVC) Guidance for the assessment of conformity
ISO 8770:2003 Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings Polyethylene (PE)
14/30297459 DC : 0 BS EN 15012 - PLASTICS PIPING SYSTEMS - BURIED AND ABOVE GROUND PIPING COMPONENTS FOR NON PRESSURE SOIL AND WASTE DISCHARGE WITHIN THE BUILDING STRUCTURE - REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR PIPES AND FITTINGS
BS EN 1366-3:2009 Fire resistance tests for service installations Penetration seals
UNE-EN 1366-3:2011 Fire resistance tests for service installations - Part 3: Penetration seals
BS EN 12666-1 : 2005 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - POLYETHYLENE (PE) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM
BS EN 12056-2:2000 Gravity drainage systems inside buildings Sanitary pipework, layout and calculation
UNI EN 1366-3 : 2009 FIRE RESISTANCE TESTS FOR SERVICE INSTALLATIONS - PART 3: PENETRATION SEALS
11/30239900 DC : DRAFT MAR 2011 BS EN 15012 - PLASTICS PIPING SYSTEMS - NON PRESSURE SOIL AND WASTE DISCHARGE PIPING COMPONENTS WITHIN THE BUILDING STRUCTURE - REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR PIPES AND FITTINGS
ISO 19220:2004 Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings Styrene copolymer blends (SAN + PVC)
EN 12380:2002 Air admittance valves for drainage systems - Requirements, tests methods and evaluation of conformity
EN 1366-3:2009 Fire resistance tests for service installations - Part 3: Penetration seals
UNE-EN 12666-1:2006 Plastics piping systems for non-pressure underground drainage and sewerage - Polyethylene (PE) - Part 1: Specifications for pipes, fittings and the system

EN 1277:2003 Plastics piping systems - Thermoplastics piping systems for buried non-pressure applications - Test methods for leaktightness of elastomeric sealing ring type joints
ISO 4440-2:1994 Thermoplastics pipes and fittings Determination of melt mass-flow rate Part 2: Test conditions
ISO/TR 10358:1993 Plastics pipes and fittings Combined chemical-resistance classification table
ISO 4440-1:1994 Thermoplastics pipes and fittings Determination of melt mass-flow rate Part 1: Test method
EN 681-1:1996/A3:2005 ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 1: VULCANIZED RUBBER
EN 728:1997 Plastics piping and ducting systems - Polyolefin pipes and fittings - Determination of oxidation induction time
ISO 265-1:1988 Pipes and fittings of plastics materials Fittings for domestic and industrial waste pipes Basic dimensions: Metric series Part 1: Unplasticized poly(vinyl chloride) (PVC-U)
EN 1566-1:1998 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Chlorinated poly(vinyl chloride) (PVC-C) - Part 1: Specifications for pipes, fittings and the system
EN 1055:1996 Plastics piping systems - Thermoplastics piping systems for soil and waste discharge inside buildings - Test method for resistance to elevated temperature cycling
ISO/TR 7620:2005 Rubber materials — Chemical resistance
EN 743 : 1994 PLASTICS PIPING AND DUCTING SYSTEMS - THERMOPLASTICS PIPES - DETERMINATION OF THE LONGITUDINAL REVERSION
EN 763 : 1994 PLASTICS PIPING AND DUCTING SYSTEMS - INJECTION MOULDED THERMOPLASTICS FITTINGS - TEST METHOD FOR VISUALLY ASSESSING EFFECTS OF HEATING
EN 1455-1:1999 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Acrylonitrile-butadiene-styrene (ABS) - Part 1: Requirements for pipes, fittings and the system
EN 921:1994/AC:1995 PLASTICS PIPING SYSTEMS - THERMOPLASTICS PIPES - DETERMINATION OF RESISTANCE TO INTERNAL PRESSURE AT CONSTANT TEMPERATURE
ISO 472:2013 Plastics Vocabulary
EN ISO 9969:2016 Thermoplastics pipes - Determination of ring stiffness (ISO 9969:2016)
EN 1401-1:2009 Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system
ISO 4065:1996 Thermoplastics pipes Universal wall thickness table
EN 1053:1995 Plastics piping systems - Thermoplastics piping systems for non-pressure applications - Test method for watertightness
ISO 1043-1:2011 Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics
EN 1565-1:1998 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Styrene copolymer blends (SAN+PVC) - Part 1: Specifications for pipes, fittings and the system
ISO 1133:2005 Plastics Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics
EN 1054:1995 Plastics piping systems - Thermoplastics piping systems for soil and waste discharge - Test method for airtightness of joints

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more