Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

EN 15836-1:2010

Current
Current

The latest, up-to-date edition.

Plastics - Plasticized poly(vinyl chloride) (PVC-P) membranes for inground swimming pools - Part 1: Homogenous membranes of nominal thickness equal to or greater than 0,75 mm
Published date

23-06-2010

Foreword
1 Scope
2 Normative references
3 Terms, definitions, symbols and abbreviations
4 Sampling and conditioning
5 PVC-P compound
6 Visual characteristics
7 Physico-chemical characteristic
8 Dimensional characteristics
9 Mechanical characteristics
10 Characteristics for durability
11 Storage conditions
12 Installation, refurbishment, exploitation and
   maintenance
13 Designation and marking
Annex A (normative) - Determination of the contents
        of CaCO[3], heavy metals and other elements
Annex B (normative) - Assessment of chlorine resistance
Annex C (normative) - Assessment of the resistance to
        staining agents
Bibliography

This European Standard specifies the visual, dimensional, mechanical and durability characteristics of plasticized poly(vinyl chloride) (PVC-P) homogenous membranes of nominal thickness greater than or equal to 0,75 mm for use as liners for inground swimming pools. It also specifies the characteristics of the composition of the PVC-P used to produce the membranes.It applies specifically to homogenous membranes intended for use in swimming pools where the water temperature is less than or equal to 28 °C. If the membrane manufacturer permits a temperature of water continuously maintained above 28 °C, this document also applies.

Committee
CEN/TC 249
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Current

13/30279623 DC : 0 BS EN 16582-2 - DOMESTIC SWIMMING POOLS - PART 2: SPECIFIC REQUIREMENT INCLUDING SAFETY AND TEST METHODS FOR INGROUND POOLS
BS EN 16927:2017 Mini-pools. Specific requirements including safety and test methods for mini-pools
I.S. EN 16582-2:2015 DOMESTIC SWIMMING POOLS - PART 2: SPECIFIC REQUIREMENTS INCLUDING SAFETY AND TEST METHODS FOR INGROUND POOLS
DIN EN 16582-2:2015-11 DOMESTIC SWIMMING POOLS - PART 2: SPECIFIC REQUIREMENTS INCLUDING SAFETY AND TEST METHODS FOR INGROUND POOLS
15/30328805 DC : 0 BS EN 16927 - MINI POOLS - SPECIFIC REQUIREMENTS INCLUDING SAFETY AND TEST METHODS FOR MINI POOLS
DIN EN 16582-1 E : 2015 DOMESTIC SWIMMING POOLS - PART 1: GENERAL REQUIREMENTS INCLUDING SAFETY AND TEST METHODS
BS EN 16582-2:2015 Domestic swimming pools Specific requirements including safety and test methods for inground pools
I.S. EN 16927:2017 MINI-POOLS - SPECIFIC REQUIREMENTS INCLUDING SAFETY AND TEST METHODS FOR MINI-POOLS
DIN EN 16927:2017-05 MINI POOLS - SPECIFIC REQUIREMENTS INCLUDING SAFETY AND TEST METHODS FOR MINI POOLS
BS EN 16582-1:2015 Domestic swimming pools General requirements including safety and test methods
I.S. EN 16582-1:2015 DOMESTIC SWIMMING POOLS - PART 1: GENERAL REQUIREMENTS INCLUDING SAFETY AND TEST METHODS
UNE-EN 16582-1:2015 Domestic swimming pools - Part 1: General requirements including safety and test methods
DIN EN 16582-2 E : 2015 DOMESTIC SWIMMING POOLS - PART 2: SPECIFIC REQUIREMENTS INCLUDING SAFETY AND TEST METHODS FOR INGROUND POOLS
13/30279620 DC : 0 BS EN 16582-1 - DOMESTIC SWIMMING POOLS - PART 1: GENERAL REQUIREMENTS INCLUDING SAFETY AND TEST METHODS
UNE-EN 16582-2:2015 Domestic swimming pools - Part 2: Specific requirements including safety and test methods for inground pools
EN 16582-2:2015 Domestic swimming pools - Part 2: Specific requirements including safety and test methods for inground pools
EN 16927:2017 Mini-pools - Specific requirements including safety and test methods for mini-pools
DIN EN 16927 E : 2017 MINI POOLS - SPECIFIC REQUIREMENTS INCLUDING SAFETY AND TEST METHODS FOR MINI POOLS
EN 16582-1:2015 Domestic swimming pools - Part 1: General requirements including safety and test methods
DIN EN 16582-1:2015-11 Domestic swimming pools - Part 1: General requirements including safety and test methods
UNE-EN 16927:2017 Mini-pools - Specific requirements including safety and test methods for mini-pools
DIN EN 16927:2015-10 (Draft) MINI POOLS - SPECIFIC REQUIREMENTS INCLUDING SAFETY AND TEST METHODS FOR MINI POOLS

ISO 7724-1:1984 Paints and varnishes Colorimetry Part 1: Principles
EN ISO 62:2008 Plastics - Determination of water absorption (ISO 62:2008)
EN ISO 5470-1:2016 Rubber- or plastics-coated fabrics - Determination of abrasion resistance - Part 1: Taber abrader (ISO 5470-1:2016)
EN 1107-2 : 2001 Flexible sheets for waterproofing - Determination of dimensional stability - Part 2: Plastic and rubber sheets for roof waterproofing
EN 1849-2:2009 Flexible sheets for waterproofing - Determination of thickness and mass per unit area - Part 2: Plastic and rubber sheets
EN 495-5:2013 Flexible sheets for waterproofing - Determination of foldability at low temperature - Part 5: Plastic and rubber sheets for roof waterproofing
EN 1848-2 : 2001 FLEXIBLE SHEETS FOR WATER-PROOFING - DETERMINATION OF LENGTH, WIDTH, STRAIGHTNESS AND FLATNESS - PLASTIC AND RUBBER SHEETS FOR ROOF WATERPROOFING
EN 15346:2014 Plastics - Recycled plastics - Characterization of poly(vinyl chloride) (PVC) recyclates
ISO 7724-2:1984 Paints and varnishes Colorimetry Part 2: Colour measurement
EN 12317-2:2010 Flexible sheets for waterproofing - Determination of shear resistance of joints - Part 2: Plastic and rubber sheets for roof waterproofing
ISO 846:1997 Plastics Evaluation of the action of microorganisms
EN ISO 527-1:2012 Plastics - Determination of tensile properties - Part 1: General principles (ISO 527-1:2012)
EN 14902:2005/AC:2006 AMBIENT AIR QUALITY - STANDARD METHOD FOR THE MEASUREMENT OF PB, CD, AS AND NI IN THE PM10 FRACTION OF SUSPENDED PARTICULATE MATTER
ISO 12572:2016 Hygrothermal performance of building materials and products Determination of water vapour transmission properties Cup method
EN 12310-2:2000 FLEXIBLE SHEETS FOR WATERPROOFING - DETERMINATION OF RESISTANCE TO TEARING - PART 2: PLASTIC AND RUBBER SHEETS FOR ROOF WATERPROOFING
EN ISO 12572:2016 Hygrothermal performance of building materials and products - Determination of water vapour transmission properties - Cup method (ISO 12572:2016)
EN 12316-2:2013 Flexible sheets for waterproofing - Determination of peel resistance of joints - Part 2: Plastic and rubber sheets for roof waterproofing
ISO 7724-3:1984 Paints and varnishes Colorimetry Part 3: Calculation of colour differences
ISO 175:2010 Plastics Methods of test for the determination of the effects of immersion in liquid chemicals
ISO 5470-1:2016 Rubber- or plastics-coated fabrics Determination of abrasion resistance Part 1: Taber abrader
ISO 1183-1:2012 Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method
EN 15347:2007 Plastics - Recycled Plastics - Characterisation of plastics wastes
ISO 291:2008 Plastics Standard atmospheres for conditioning and testing
EN ISO 846 : 1997 PLASTICS - EVALUATION OF THE ACTION OF MICROORGANISMS
ISO 62:2008 Plastics Determination of water absorption
EN ISO 291:2008 Plastics - Standard atmospheres for conditioning and testing (ISO 291:2008)
ISO 4892-2:2013 Plastics — Methods of exposure to laboratory light sources — Part 2: Xenon-arc lamps
EN 438-2:2016 High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually called laminates) - Part 2: Determination of properties
EN 20105-A02 : 1994 TEXTILES - TESTS FOR COLOUR FASTNESS - PART A02: GREYSCALE FOR ASSESSING CHANGE IN COLOUR (ISO 105-A02:1993)
ISO 105-A02:1993 Textiles Tests for colour fastness Part A02: Grey scale for assessing change in colour
ISO 527-3:1995 Plastics Determination of tensile properties Part 3: Test conditions for films and sheets
EN ISO 527-3:1995/AC:2002 PLASTICS - DETERMINATION OF TENSILE PROPERTIES - PART 3: TEST CONDITIONS FOR FILMS AND SHEETS
EN ISO 4892-2:2013 Plastics - Methods of exposure to laboratory light sources - Part 2: Xenon-arc lamps (ISO 4892-2:2013)
EN ISO 1183-1:2012 Plastics - Methods for determining the density of non-cellular plastics - Part 1: Immersion method, liquid pyknometer method and titration method (ISO 1183-1:2012)
EN 1850-2 : 2001 FLEXIBLE SHEETS FOR WATERPROOFING - DETERMINATION OF VISIBLE DEFECTS - PART 2: PLASTIC AND RUBBER SHEETS FOR ROOF WATERPROOFING
EN ISO 175:2010 Plastics - Methods of test for the determination of the effects of immersion in liquid chemicals (ISO 175:2010)
ISO 527-1:2012 Plastics Determination of tensile properties Part 1: General principles

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more