EN 16192:2011
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Characterization of waste - Analysis of eluates
Superseded date
16-03-2022
Published date
23-11-2011
Publisher
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Sample pretreatment
5 Blank determination
6 Interference
7 Selection of the suitable test method
8 Expression of results
9 Test report
Annex A (informative) - Validation of EN 12506:2003 and
EN 13370:2003
Annex B (informative) - Additional validation data
Bibliography
This European Standard specifies methods for the determination of the parameters pH, ammonium, AOX, As, Ba, Cd, Cl-, easily liberatable CN-, Co, Cr, Cr(VI), Cu, DOC/TOC, electrical conductivity, F-, Hg, Mo, Ni, NO2-, Pb, phenol index, total S, Sb, Se, SO42-, TDS, V and Zn in aqueous eluates for the characterization of waste.
| Committee |
CEN/TC 444
|
| DevelopmentNote |
Supersedes PREN 16192, EN 12506 & EN 13370. (12/2011)
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| NBN EN 16192 : 2012 | Identical |
| SN EN 16192 : 2012 | Identical |
| UNI EN 16192 : 2012 | Identical |
| DIN EN 16192:2012-02 | Identical |
| NEN EN 16192 : 2011 | Identical |
| NF EN 16192 : 2012 | Identical |
| NS EN 16192 : 2011 | Identical |
| PN EN 16192 : 2012 | Identical |
| UNE-EN 16192:2012 | Identical |
| BS EN 16192:2011 | Identical |
| I.S. EN 16192:2011 | Identical |
| IEC 62561-7:2018 | Lightning protection system components (LPSC) - Part 7: Requirements for earthing enhancing compounds |
| UNE-EN 14429:2015 | Characterization of waste - Leaching behaviour test - Influence of pH on leaching with initial acid/base addition |
| BS EN 14405:2017 | Characterization of waste - Leaching behaviour test - Up-flow percolation test (under specified conditions) |
| 14/30304804 DC : 0 | BS EN 14405 - CHARACTERISATION OF WASTE - LEACHING BEHAVIOUR TEST - UP-FLOW PERCOLATION TEST (UNDER SPECIFIED CONDITIONS) |
| 17/30354239 DC : 0 | BS EN 13369 - COMMON RULES FOR PRECAST CONCRETE PRODUCTS |
| DIN EN 15863:2015-06 | CHARACTERIZATION OF WASTE - LEACHING BEHAVIOUR TEST FOR BASIC CHARACTERIZATION - DYNAMIC MONOLITHIC LEACHING TEST WITH PERIODIC LEACHANT RENEWAL, UNDER FIXED CONDITIONS |
| UNE-EN 16123:2013 | Characterization of waste - Guidance on selection and application of screening methods |
| EN 14997:2015 | Characterization of waste - Leaching behaviour test - Influence of pH on leaching with continuous pH control |
| CEN/TS 15862:2012 | Characterisation of waste - Compliance leaching test - One stage batch leaching test for monoliths at fixed liquid to surface area ratio (L/A) for test portions with fixed minimum dimensions |
| EN 14405:2017 | Characterization of waste - Leaching behaviour test - Up-flow percolation test (under specified conditions) |
| CEN/TS 16637-3:2016 | Construction products - Assessment of release of dangerous substances - Part 3: Horizontal up-flow percolation test |
| EN 15863:2015 | Characterization of waste - Leaching behaviour test for basic characterization - Dynamic monolithic leaching test with periodic leachant renewal, under fixed conditions |
| CEN/TS 16637-2:2014 | Construction products - Assessment of release of dangerous substances - Part 2: Horizontal dynamic surface leaching test |
| DIN EN 14997:2015-05 | CHARACTERIZATION OF WASTE - LEACHING BEHAVIOUR TEST - INFLUENCE OF PH ON LEACHING WITH CONTINUOUS PH CONTROL |
| UNI EN 16457 : 2014 | CHARACTERIZATION OF WASTE - FRAMEWORK FOR THE PREPARATION AND APPLICATION OF A TESTING PROGRAMME - OBJECTIVES, PLANNING AND REPORT |
| DIN EN 14405 E : 2017 | CHARACTERIZATION OF WASTE - LEACHING BEHAVIOUR TEST - UP-FLOW PERCOLATION TEST (UNDER SPECIFIED CONDITIONS) |
| UNI EN 13369 : 2013 | COMMON RULES FOR PRECAST CONCRETE PRODUCTS |
| PREN 14429 : DRAFT 2013 | CHARACTERISATION OF WASTE - LEACHING BEHAVIOUR TEST - INFLUENCE OF PH ON LEACHING WITH INITIAL ACID/BASE ADDITION |
| EN IEC 62561-7:2018 | Lightning protection system components (LPSC) - Part 7: Requirements for earthing enhancing compounds |
| BS EN 13369:2013 | Common rules for precast concrete products |
| I.S. EN 16457:2014 | CHARACTERIZATION OF WASTE - FRAMEWORK FOR THE PREPARATION AND APPLICATION OF A TESTING PROGRAMME - OBJECTIVES, PLANNING AND REPORT |
| PREN 14405 : DRAFT 2014 | CHARACTERISATION OF WASTE - LEACHING BEHAVIOUR TEST - UP-FLOW PERCOLATION TEST (UNDER SPECIFIED CONDITIONS) |
| UNE-EN 14405:2017 | Characterization of waste - Leaching behaviour test - Up-flow percolation test (under specified conditions) |
| I.S. EN 16123:2013 | CHARACTERIZATION OF WASTE - GUIDANCE ON SELECTION AND APPLICATION OF SCREENING METHODS |
| UNI EN 16123 : 2013 | CHARACTERIZATION OF WASTE - GUIDANCE ON SELECTION AND APPLICATION OF SCREENING METHODS |
| DIN EN 15863 E : 2015 | CHARACTERIZATION OF WASTE - LEACHING BEHAVIOUR TEST FOR BASIC CHARACTERIZATION - DYNAMIC MONOLITHIC LEACHING TEST WITH PERIODIC LEACHANT RENEWAL, UNDER FIXED CONDITIONS |
| 17/30348303 DC : 0 | BS EN 17087 - CONSTRUCTION PRODUCTS - ASSESSMENT OF RELEASE OF DANGEROUS SUBSTANCES - PREPARATION OF TEST PORTIONS FROM THE LABORATORY SAMPLE FOR TESTING OF RELEASE AND ANALYSIS OF CONTENT |
| UNE-EN 15863:2015 | Characterization of waste - Leaching behaviour test for basic characterization - Dynamic monolithic leaching test with periodic leachant renewal, under fixed conditions |
| UNE-EN 15002:2015 | Characterization of waste - Preparation of test portions from the laboratory sample |
| S.R. CEN/TS 15863:2012 | CHARACTERISATION OF WASTE - LEACHING BEHAVIOUR TEST FOR BASIC CHARACTERISATION - DYNAMIC MONOLITHIC LEACHING TEST WITH PERIODIC LEACHANT RENEWAL, UNDER FIXED TEST CONDITIONS |
| I.S. EN 15002:2015 | CHARACTERIZATION OF WASTE - PREPARATION OF TEST PORTIONS FROM THE LABORATORY SAMPLE |
| S.R. CEN/TS 15862:2012 | CHARACTERISATION OF WASTE - COMPLIANCE LEACHING TEST - ONE STAGE BATCH LEACHING TEST FOR MONOLITHS AT FIXED LIQUID TO SURFACE AREA RATIO (L/A) FOR TEST PORTIONS WITH FIXED MINIMUM DIMENSIONS |
| DIN EN 14429 E : 2015 | CHARACTERIZATION OF WASTE - LEACHING BEHAVIOUR TEST - INFLUENCE OF PH ON LEACHING WITH INITIAL ACID/BASE ADDITION |
| DIN EN 16123:2013-05 | Characterization of waste - Guidance on selection and application of screening methods |
| BS EN 16123:2013 | Characterization of waste. Guidance on selection and application of screening methods |
| UNE-EN 14997:2015 | Characterization of waste - Leaching behaviour test - Influence of pH on leaching with continuous pH control |
| UNE-EN 16457:2014 | Characterization of waste - Framework for the preparation and application of a testing programme - Objectives, planning and report |
| EN 16123:2013 | Characterization of waste - Guidance on selection and application of screening methods |
| DIN EN 13369:2013-08 | COMMON RULES FOR PRECAST CONCRETE PRODUCTS |
| I.S. EN 13369:2013 | COMMON RULES FOR PRECAST CONCRETE PRODUCTS |
| UNI CEN/TS 15862 : 2012 | CHARACTERISATION OF WASTE - COMPLIANCE LEACHING TEST - ONE STAGE BATCH LEACHING TEST FOR MONOLITHS AT FIXED LIQUID TO SURFACE AREA RATIO (L/A) FOR TEST PORTIONS WITH FIXED MINIMUM DIMENSIONS |
| DIN EN 14405:2017-05 | CHARACTERIZATION OF WASTE - LEACHING BEHAVIOUR TEST - UP-FLOW PERCOLATION TEST (UNDER SPECIFIED CONDITIONS) |
| PD CEN/TS 15864:2012 | Characterisation of waste. Leaching behaviour test for basic characterisation. Dynamic monolithic leaching test with continuous leachant renewal under conditions relevant for specified scenario(s) |
| PD CEN/TS 16637-3:2016 | Construction products. Assessment of release of dangerous substances Horizontal up-flow percolation test |
| I.S. EN 15863:2015 | CHARACTERIZATION OF WASTE - LEACHING BEHAVIOUR TEST FOR BASIC CHARACTERIZATION - DYNAMIC MONOLITHIC LEACHING TEST WITH PERIODIC LEACHANT RENEWAL, UNDER FIXED CONDITIONS |
| PREN 13369 : DRAFT 2017 | COMMON RULES FOR PRECAST CONCRETE PRODUCTS |
| I.S. EN 14405:2017 | CHARACTERIZATION OF WASTE - LEACHING BEHAVIOUR TEST - UP-FLOW PERCOLATION TEST (UNDER SPECIFIED CONDITIONS) |
| DIN EN 14997 E : 2015 | CHARACTERIZATION OF WASTE - LEACHING BEHAVIOUR TEST - INFLUENCE OF PH ON LEACHING WITH CONTINUOUS PH CONTROL |
| PD CEN/TS 16637-2:2014 | Construction products. Assessment of release of dangerous substances Horizontal dynamic surface leaching test |
| DIN EN 14429:2015-05 | CHARACTERIZATION OF WASTE - LEACHING BEHAVIOUR TEST - INFLUENCE OF PH ON LEACHING WITH INITIAL ACID/BASE ADDITION |
| 12/30263896 DC : 0 | BS EN 16457 - CHARACTERIZATION OF WASTE - FRAMEWORK FOR THE PREPARATION AND APPLICATION OF A TESTING PROGRAMME - OBJECTIVES, PLANNING AND REPORT |
| DIN EN 16457:2014-07 | CHARACTERIZATION OF WASTE - FRAMEWORK FOR THE PREPARATION AND APPLICATION OF A TESTING PROGRAMME - OBJECTIVES, PLANNING AND REPORT |
| S.R. CEN/TS 16637-2:2014 | CONSTRUCTION PRODUCTS - ASSESSMENT OF RELEASE OF DANGEROUS SUBSTANCES - PART 2: HORIZONTAL DYNAMIC SURFACE LEACHING TEST |
| S.R. CEN/TS 16637-3:2016 | CONSTRUCTION PRODUCTS - ASSESSMENT OF RELEASE OF DANGEROUS SUBSTANCES - PART 3: HORIZONTAL UP-FLOW PERCOLATION TEST |
| I.S. EN 14429:2015 | CHARACTERIZATION OF WASTE - LEACHING BEHAVIOUR TEST - INFLUENCE OF PH ON LEACHING WITH INITIAL ACID/BASE ADDITION |
| S.R. CEN/TS 15864:2015 | CHARACTERISATION OF WASTE - LEACHING BEHAVIOUR TEST FOR BASIC CHARACTERIZATION - DYNAMIC MONOLITHIC LEACHING TEST WITH CONTINUOUS LEACHANT RENEWAL UNDER CONDITIONS RELEVANT FOR SPECIFIED SCENARIO(S) |
| PD CEN/TS 15862:2012 | Characterisation of waste. Compliance leaching test. One stage batch leaching test for monoliths at fixed liquid to surface area ratio (L/A) for test portions with fixed minimum dimensions |
| PD CEN/TS 15863:2012 | Characterisation of waste. Leaching behaviour test for basic characterisation. Dynamic monolithic leaching test with periodic leachant renewal, under fixed test conditions |
| 13/30291099 DC : 0 | BS EN 15002 - CHARACTERIZATION OF WASTE - PREPARATION OF TEST PORTIONS FROM THE LABORATORY SAMPLE |
| BS EN 15863:2015 | Characterization of waste. Leaching behaviour test for basic characterization. Dynamic monolithic leaching test with periodic leachant renewal, under fixed conditions |
| DIN EN 15002:2015-07 | CHARACTERIZATION OF WASTE - PREPARATION OF TEST PORTIONS FROM THE LABORATORY SAMPLE |
| EN 15002:2015 | Characterization of waste - Preparation of test portions from the laboratory sample |
| EN 16457:2014 | Characterization of waste - Framework for the preparation and application of a testing programme - Objectives, planning and report |
| BS EN 14997:2015 | Characterization of waste. Leaching behaviour test. Influence of pH on leaching with continuous pH control |
| 13/30286649 DC : 0 | BS EN 14429 - CHARACTERISATION OF WASTE - LEACHING BEHAVIOUR TEST - INFLUENCE OF PH ON LEACHING WITH INITIAL ACID/BASE ADDITION |
| BS EN 14429:2015 | Characterization of waste. Leaching behaviour test. Influence of pH on leaching with initial acid/base addition |
| DIN EN 16457 E : 2014 | CHARACTERIZATION OF WASTE - FRAMEWORK FOR THE PREPARATION AND APPLICATION OF A TESTING PROGRAMME - OBJECTIVES, PLANNING AND REPORT |
| 13/30286652 DC : 0 | BS EN 14997 - CHARACTERISATION OF WASTE - LEACHING BEHAVIOUR TEST - INFLUENCE OF PH ON LEACHING WITH CONTINUOUS PH CONTROL |
| BS EN 16457:2014 | Characterization of waste. Framework for the preparation and application of a testing programme. Objectives, planning and report |
| UNE-EN 13369:2013 | Common rules for precast concrete products |
| I.S. EN IEC 62561-7:2018 | LIGHTNING PROTECTION SYSTEM COMPONENTS (LPSC) - PART 7: REQUIREMENTS FOR EARTHING ENHANCING COMPOUNDS |
| I.S. EN 13369:2018 | COMMON RULES FOR PRECAST CONCRETE PRODUCTS |
| I.S. EN 14997:2015 | CHARACTERIZATION OF WASTE - LEACHING BEHAVIOUR TEST - INFLUENCE OF PH ON LEACHING WITH CONTINUOUS PH CONTROL |
| UNI CEN/TS 16637-2 : 2014 | CONSTRUCTION PRODUCTS - ASSESSMENT OF RELEASE OF DANGEROUS SUBSTANCES - PART 2: HORIZONTAL DYNAMIC SURFACE LEACHING TEST |
| EN 13369:2018 | Common rules for precast concrete products |
| DIN EN 15002 E : 2015 | CHARACTERIZATION OF WASTE - PREPARATION OF TEST PORTIONS FROM THE LABORATORY SAMPLE |
| 13/30286655 DC : 0 | BS EN 15863 - CHARACTERIZATION OF WASTE - LEACHING BEHAVIOUR TEST FOR BASIC CHARACTERIZATION - DYNAMIC MONOLITHIC LEACHING TEST WITH PERIODIC LEACHANT RENEWAL, UNDER FIXED TEST CONDITIONS |
| BS EN 15002:2015 | Characterization of waste. Preparation of test portions from the laboratory sample |
| CEN/TS 15864:2015 | Characterization of waste - Leaching behaviour test for basic characterization - Dynamic monolithic leaching test with continuous leachant renewal under conditions relevant for specified scenario(s) |
| EN 14429:2015 | Characterization of waste - Leaching behaviour test - Influence of pH on leaching with initial acid/base addition |
| CEN/TS 15863:2012 | Characterisation of waste - Leaching behaviour test for basic characterisation - Dynamic monolithic leaching test with periodic leachant renewal, under fixed test conditions |
| ISO 23913:2006 | Water quality — Determination of chromium(VI) — Method using flow analysis (FIA and CFA) and spectrometric detection |
| ISO/IEC 17025:2005 | General requirements for the competence of testing and calibration laboratories |
| ISO 5725-1:1994 | Accuracy (trueness and precision) of measurement methods and results — Part 1: General principles and definitions |
| EN ISO 17294-1:2006 | Water quality - Application of inductively coupled plasma mass spectrometry (ICP-MS) - Part 1: General guidelines (ISO 17294-1:2004) |
| EN ISO 14403 : 2002 | WATER QUALITY - DETERMINATION OF TOTAL CYANIDE AND FREE CYANIDE BY CONTINUOUS FLOW ANALYSIS |
| ISO 14402:1999 | Water quality Determination of phenol index by flow analysis (FIA and CFA) |
| EN 12457-2:2002 | Characterisation of waste - Leaching - Compliance test for leaching of granular waste materials and sludges - Part 2: One stage batch test at a liquid to solid ratio of 10 l/kg for materials with particle size below 4 mm (without or with size reduction) |
| EN 1483:2007 | Water quality - Determination of mercury - Method using atomic absorption spectrometry |
| CEN/TS 14429:2005 | Characterization of waste - Leaching behaviour tests - Influence of pH on leaching with initial acid/base addition |
| EN ISO 11885:2009 | Water quality - Determination of selected elements by inductively coupled plasma optical emission spectrometry (ICP-OES) (ISO 11885:2007) |
| EN 27888 : 1993 | WATER QUALITY - DETERMINATION OF ELECTRICAL CONDUCTIVITY |
| ISO 11969:1996 | Water quality Determination of arsenic Atomic absorption spectrometric method (hydride technique) |
| ISO 11083:1994 | Water quality — Determination of chromium(VI) — Spectrometric method using 1,5-diphenylcarbazide |
| EN ISO 10304-3 : 1997 | Water quality - Determination of dissolved anions by liquid chromatography of ions - Part 3: Determination of chromate, iodide, sulfite, thiocyanate and thiosulfate (ISO 10304-3:1997) |
| EN ISO 11732:2005 | Water quality - Determination of ammonium nitrogen - Method by flow analysis (CFA and FIA) and spectrometric detection (ISO 11732:2005) |
| EN ISO 15586 : 2003 | WATER QUALITY - DETERMINATION OF TRACE ELEMENTS USING ATOMIC ABSORPTION SPECTROMETRY WITH GRAPHITE FURNACE |
| ISO/TR 13530:1997 | Water quality Guide to analytical quality control for water analysis |
| EN 26777 : 1993 | WATER QUALITY - DETERMINATION OF NITRITE - MOLECULAR ABSORPTION SPECTROMETRIC METHOD |
| EN 1484 : 1997 | WATER ANALYSIS - GUIDELINES FOR THE DETERMINATION OF TOTAL ORGANIC CARBON (TOC) AND DISSOLVED ORGANIC CARBON (DOC) |
| ISO 10304-3:1997 | Water quality — Determination of dissolved anions by liquid chromatography of ions — Part 3: Determination of chromate, iodide, sulfite, thiocyanate and thiosulfate |
| ISO 11732:2005 | Water quality — Determination of ammonium nitrogen — Method by flow analysis (CFA and FIA) and spectrometric detection |
| ISO 15682:2000 | Water quality Determination of chloride by flow analysis (CFA and FIA) and photometric or potentiometric detection |
| ISO 17852:2006 | Water quality Determination of mercury Method using atomic fluorescence spectrometry |
| ISO 5725-3:1994 | Accuracy (trueness and precision) of measurement methods and results — Part 3: Intermediate measures of the precision of a standard measurement method |
| CEN/TS 14997 : 2006 | CHARACTERIZATION OF WASTE - LEACHING BEHAVIOUR TESTS - INFLUENCE OF PH ON LEACHING WITH CONTINUOUS PH-CONTROL |
| ISO 9965:1993 | Water quality Determination of selenium Atomic absorption spectrometric method (hydride technique) |
| ISO 5725-6:1994 | Accuracy (trueness and precision) of measurement methods and results — Part 6: Use in practice of accuracy values |
| EN 12457-4:2002 | Characterisation of waste - Leaching - Compliance test for leaching of granular waste materials and sludges - Part 4: One stage batch test at a liquid to solid ratio of 10 l/kg for materials with particle size below 10 mm (without or with size reduction) |
| ISO 8288:1986 | Water quality — Determination of cobalt, nickel, copper, zinc, cadmium and lead — Flame atomic absorption spectrometric methods |
| ISO 5725-4:1994 | Accuracy (trueness and precision) of measurement methods and results Part 4: Basic methods for the determination of the trueness of a standard measurement method |
| ISO 9297:1989 | Water quality Determination of chloride Silver nitrate titration with chromate indicator (Mohr's method) |
| EN ISO 17852:2008 | Water quality - Determination of mercury - Method using atomic fluorescence spectrometry (ISO 17852:2006) |
| EN ISO 23913:2009 | Water quality - Determination of chromium(VI) - Method using flow analysis (FIA and CFA) and spectrometric detection (ISO 23913:2006) |
| ISO 11885:2007 | Water quality Determination of selected elements by inductively coupled plasma optical emission spectrometry (ICP-OES) |
| ISO 17294-1:2004 | Water quality — Application of inductively coupled plasma mass spectrometry (ICP-MS) — Part 1: General guidelines |
| ISO 10304-1:2007 | Water quality Determination of dissolved anions by liquid chromatography of ions Part 1: Determination of bromide, chloride, fluoride, nitrate, nitrite, phosphate and sulfate |
| ISO 6703-2:1984 | Water quality — Determination of cyanide — Part 2: Determination of easily liberatable cyanide |
| ISO 6439:1990 | Water quality — Determination of phenol index — 4-Aminoantipyrine spectrometric methods after distillation |
| ISO 13395:1996 | Water quality — Determination of nitrite nitrogen and nitrate nitrogen and the sum of both by flow analysis (CFA and FIA) and spectrometric detection |
| ISO 10359-1:1992 | Water quality — Determination of fluoride — Part 1: Electrochemical probe method for potable and lightly polluted water |
| CEN/TR 16184:2011 | Characterization of Waste - State-of-the-art document - Analysis of eluates |
| ENV ISO 13530 : DRAFT 1998 | WATER QUALITY - GUIDE TO ANALYTICAL QUALITY CONTROL FOR WATER ANALYSIS |
| ISO 15586:2003 | Water quality Determination of trace elements using atomic absorption spectrometry with graphite furnace |
| NEN 6604 : 2007 | WATER QUALITY - DETERMINATION OF AMMONIUM, NITRATE, NITRITE, CHLORIDE, ORTHO-PHOSPHATE, SULPHATE AND SILICATE BY A DISCRETE ANALYZER SYSTEM AND SPECTROPHOTOMETRIC DETECTION |
| ISO 7888:1985 | Water quality — Determination of electrical conductivity |
| EN 12457-1:2002 | Characterisation of waste - Leaching - Compliance test for leaching of granular waste materials and sludges - Part 1: One stage batch test at a liquid to solid ratio of 2 l/kg for materials with high solid content and with particle size below 4 mm (without or with size reduction) |
| ISO 5725-2:1994 | Accuracy (trueness and precision) of measurement methods and results Part 2: Basic method for the determination of repeatability and reproducibility of a standard measurement method |
| ISO 14403:2002 | Water quality Determination of total cyanide and free cyanide by continuous flow analysis |
| ISO 9562:2004 | Water quality — Determination of adsorbable organically bound halogens (AOX) |
| ISO 22743:2006 | Water quality Determination of sulfates Method by continuous flow analysis (CFA) |
| EN 12920:2006+A1:2008 | Characterization of waste - Methodology for the determination of the leaching behaviour of waste under specified conditions |
| EN 15002:2015 | Characterization of waste - Preparation of test portions from the laboratory sample |
| EN ISO 15682 : 2001 | WATER QUALITY - DETERMINATION OF CHLORIDE BY FLOW ANALYSIS (CFA AND FIA) AND PHOTOMETRIC OR POTENTIOMETRIC DETECTION |
| EN 12457-3:2002 | Characterisation of waste - Leaching - Compliance test for leaching of granular waste materials and sludges - Part 3: Two stage batch test at a liquid to solid ratio of 2 l/kg and 8 l/kg for materials with high solid content and with particle size below 4 mm (without or with size reduction) |
| EN 12506:2003 | Characterization of waste - Analysis of eluates - Determination of pH, As, Ba, Cd, Cl-, Co, Cr, Cr Vl, Cu, Mo, Ni, NO2-, Pb, total S, SO42-, V and Zn |
| EN ISO 9562:2004 | Water quality - Determination of adsorbable organically bound halogens (AOX) (ISO 9562:2004) |
| ISO 7150-1:1984 | Water quality — Determination of ammonium — Part 1: Manual spectrometric method |
| CEN/TS 14405 : 2004 | CHARACTERIZATION OF WASTE - LEACHING BEHAVIOUR TESTS - UP-FLOW PERCOLATION TEST (UNDER SPECIFIED CONDITIONS) |
| ISO 10523:2008 | Water quality — Determination of pH |
| EN 15216:2007 | Characterization of waste - Determination of total dissolved solids (TDS) in water and eluates |
| EN ISO 11969:1996 | WATER QUALITY - DETERMINATION OF ARSENIC - ATOMIC ABSORPTION SPECTROMETRIC METHOD (HYDRIDE TECHNIQUE) |
| ISO 5725-5:1998 | Accuracy (trueness and precision) of measurement methods and results — Part 5: Alternative methods for the determination of the precision of a standard measurement method |
| EN ISO 14402 : 1999 | WATER QUALITY - DETERMINATION OF PHENOL INDEX BY FLOW ANALYSIS (FIA AND CFA) |
| EN ISO 10304-1:2009 | Water quality - Determination of dissolved anions by liquid chromatography of ions - Part 1: Determination of bromide, chloride, fluoride, nitrate, nitrite, phosphate and sulfate (ISO 10304-1:2007) |
| ISO 17294-2:2016 | Water quality — Application of inductively coupled plasma mass spectrometry (ICP-MS) — Part 2: Determination of selected elements including uranium isotopes |
| EN ISO 14911 : 1999 | WATER QUALITY - DETERMINATION OF DISSOLVED LI+, NA+, NH4+, K+, MN2+, CA2+, MG2+, SR2+ AND BA2+ USING ION CHROMATOGRAPHY - METHOD FOR WATER AND WASTE WATER |
| EN ISO 17294-2:2016 | Water quality - Application of inductively coupled plasma mass spectrometry (ICP-MS) - Part 2: Determination of selected elements including uranium isotopes (ISO 17294-2:2016) |
| ISO 14911:1998 | Water quality Determination of dissolved Li+, Na+, NH4+, K+, Mn2+, Ca2+, Mg2+, Sr2+ and Ba2+ using ion chromatography Method for water and waste water |
| EN ISO 13395 : 1996 | WATER QUALITY - DETERMINATION OF NITRITE NITROGEN AND NITRATE NITROGEN AND THE SUM OF BOTH BY FLOW ANALYSIS (CFA AND FIA) AND SPECTROMETRIC DETECTION |
Sorry this product is not available in your region.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.