Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

EN 50216-10:2009

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Power transformer and reactor fittings - Part 10: Oil-to-air heat exchangers
Superseded date

28-01-2022

Published date

06-03-2009

1 Scope
2 Normative references
3 Definitions
4 Requirements
  4.1 Rated values
  4.2 Rated cooling capacity
  4.3 Mechanical design
  4.4 Protection of surfaces
5 Designation
  5.1 Designation of the heat exchangers
  5.2 Rating plate information
6 Tests
  6.1 Routine tests
  6.2 Type tests
7 Preparation for transport and storage
8 Mounting and service, service conditions
Annex A (normative) - Design details of heat exchangers
Annex B (normative) - Performance of heat exchangers
Bibliography

EN 50216-10 describes oil-to-air heat exchangers that means a heat exchanger for the cooling of the transformer oil using a forced oil circuit and a forced air circuit. The oil-to-air heat exchangers are not included in the scope of the Pressure Equipment Directive 97/23/EC according to Article 1, § 3.12. This standard establishes essential dimensions and the requirements to ensure interchangeability and adequate mounting of the oil-to-air heat exchangers. This standard applies for dimensions and requirements of oil-to-air heat exchangers. The increase of ratings and constructional changes as well are considered in the revised standard.

Committee
CLC/TC 14
DevelopmentNote
To be read in conjunction with EN 50216-1. (03/2009)
DocumentType
Standard
PublisherName
European Committee for Standards - Electrical
Status
Superseded
SupersededBy

I.S. EN 50216-12:2011 POWER TRANSFORMER AND REACTOR FITTINGS - PART 12: FANS
UNE-EN 50216-12:2011 Power transformer and reactor fittings - Part 12: Fans
EN 50216-12:2011 Power transformer and reactor fittings - Part 12: Fans
BS EN 50216-12:2011 Power transformer and reactor fittings Fans

ISO 3506-1:2009 Mechanical properties of corrosion-resistant stainless steel fasteners Part 1: Bolts, screws and studs
EN 10027-2:2015 DESIGNATION SYSTEMS FOR STEELS - PART 2: NUMERICAL SYSTEM
EN ISO 3506-1:2009 Mechanical properties of corrosion-resistant stainless steel fasteners - Part 1: Bolts, screws and studs (ISO 3506-1:2009)
EN ISO 1461:2009 Hot dip galvanized coatings on fabricated iron and steel articles - Specifications and test methods (ISO 1461:2009)
EN 10025:1990/A1:1993 HOT ROLLED PRODUCTS OF NON-ALLOY STRUCTURAL STEELS - TECHNICAL DELIVERY CONDITIONS
ISO 1461:2009 Hot dip galvanized coatings on fabricated iron and steel articles — Specifications and test methods
EN 10088-2:2014 STAINLESS STEELS - PART 2: TECHNICAL DELIVERY CONDITIONS FOR SHEET/PLATE AND STRIP OF CORROSION RESISTING STEELS FOR GENERAL PURPOSES
IEC 60296:2012 RLV Fluids for electrotechnical applications - Unused mineral insulating oils for transformers and switchgear
EN 60296:2012 Fluids for electrotechnical applications - Unused mineral insulating oils for transformers and switchgear
EN 10130:2006 Cold rolled low carbon steel flat products for cold forming - Technical delivery conditions
EN 754-2:2016 Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 2: Mechanical properties
EN 1386:2007 Aluminium and aluminium alloys - Tread plate - Specifications
EN 60721-3-4:1995/A1:1997 CLASSIFICATION OF ENVIRONMENTAL CONDITIONS - PART 3: CLASSIFICATION OF GROUPS OF ENVIRONMENTAL PARAMETERS AND THEIR SEVERITIES - SECTION 4: STATIONARY USE AT NON-WEATHER-PROTECTED LOCATIONS
EN 10217-1:2002/A1:2005 WELDED STEEL TUBES FOR PRESSURE PURPOSES - TECHNICAL DELIVERY CONDITIONS - NON-ALLOY STEEL TUBES WITH SPECIFIED ROOM TEMPERATURE PROPERTIES
EN 12451:2012 Copper and copper alloys - Seamless, round tubes for heat exchangers
1997/23/EC : 1997 DIRECTIVE 97/23/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 29 MAY 1997 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES CONCERNING PRESSURE EQUIPMENT
EN 50216-1:2002 Power transformer and reactor fittings - Part 1: General

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more