Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

EN 545:2010

Current
Current

The latest, up-to-date edition.

Ductile iron pipes, fittings, accessories and their joints for water pipelines - Requirements and test methods
Published date

22-09-2010

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Technical requirements
5 Performance requirements for joints and pipe saddles
6 Test methods
7 Performance test methods
8 Tables of dimensions
9 Evaluation of conformity
Annex A (normative) Allowable pressures
Annex B (informative) Longitudinal bending resistance of pipes
Annex C (informative) Diametral stiffness of pipes
Annex D (informative) Specific coatings, field of use,
                      characteristics of soils
Annex E (informative) Field of use, water characteristics
Annex F (informative) Calculation method of buried pipelines,
                      heights of cover
Bibliography

This European Standard specifies the requirements and associated test methods applicable to ductile iron pipes, fittings, accessories and their joints for the construction of pipelines outside buildings:-to convey different types of water (e.g. raw water, treated water, re-used water) for all types of applications (e.g. water intended for human consumption, for fire protection, for snow making, for irrigation, for hydro-electricity etc.);-with or without pressure;-to be installed below or above ground.This European Standard is applicable to pipes, fittings and accessories which are: -manufactured with socketed, flanged or spigot ends;-supplied externally and internally coated;- suitable for fluid temperatures between 0 °C and 50 °C, excluding frost;-not intended for use in areas subject to fire regulations.NOTE 1This does not preclude special arrangements for the products to be used at higher temperatures.This European Standard covers pipes and fittings cast by any type of foundry process or manufactured by fabrication of cast components, as well as corresponding joints and accessories, in a size range extending from DN 40 to DN 2 000, inclusive.This European Standard specifies requirements for materials, dimensions and tolerances, mechanical properties and standard coatings of ductile iron pipes and fittings. It also gives performance requirements for all components including joints. Joint design and gasket shapes are outside the scope of this standard.In addition, reference is made to the performance requirements of couplings, flange adaptors and saddles manufactured for use with ductile iron pipes and fittings.NOTE 2In this European Standard, all pressures are relative pressures, expressed in bars (100 kPa = 1 bar).

Committee
CEN/TC 203
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Current
Supersedes

Standards Relationship
UNI EN 545 : 2010 Identical
UNE-EN 545:2011 Identical
BS EN 545:2010 Identical
I.S. EN 545:2010 Identical
NS EN 545 : 1ED 2010 Identical
NBN EN 1559-3 : 2011 Identical
SN EN 545 : 2010 Identical
NEN EN 545 : 2010 Identical
NBN EN 545 : 2010 Identical
PN EN 545 : 2010 Identical
NF EN 545 : 2010 Identical
SANS 50545 : 3ED 2014 Identical
DIN EN 545:2011-09 Identical
SANS 50545 3ED:2014(R2022) Identical

DIN 28602:2000-05 DUCTILE IRON PIPES AND FITTINGS - BOLTED GLAND JOINTS - ASSEMBLY, SOCKETS, COUNTER RING, SEALING RING, BOLTS AND NUTS
01/711715 DC : DRAFT AUG 2001 BS EN 12502-5 - PROTECTION OF METALLIC MATERIALS AGAINST CORROSION - CORROSION LIKELIHOOD IN WATER CONVEYING SYSTEMS - PART 5 - REVIEW OF INFLUENCING FACTORS FOR CAST IRON, UNALLOYED AND LOW ALLOYED STEELS
UNI CEN/TR 16017 : 2010 GUIDE TO THE USE OF EN 598
PREN 1171 : DRAFT 2014 INDUSTRIAL VALVES - CAST IRON GATE VALVES
PREN 598 : DRAFT 2017 COATED AND LINED DUCTILE IRON PIPES, FITTINGS AND THEIR JOINTS FOR SEWERAGE AND DRAINAGE APPLICATIONS - PRODUCTS CHARACTERISTICS AND TEST AND ASSESSMENT METHODS
UNE-EN 1563:2012 Founding - Spheroidal graphite cast irons
03/104248 DC : DRAFT FEB 2003 EN 14628 - DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - EXTERNAL POLYETHYLENE COATING FOR PIPES IN HIGHLY AGGRESSIVE SOILS - REQUIREMENTS AND TEST METHODS
05/30134037 DC : 0 EN 12516-4 - INDUSTRIAL VALVES - SHELL DESIGN STRENGTH - PART 4: CALCULATION METHOD FOR VALVE SHELLS MANUFACTURED IN METALLIC MATERIALS OTHER THAN STEEL
BS EN 593:2017 Industrial valves. Metallic butterfly valves for general purposes
14/30294800 DC : 0 BS EN 14901 - DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - EPOXY COATING (HEAVY DUTY) OF DUCTILE IRON FITTINGS AND ACCESSORIES - REQUIREMENTS AND TEST METHODS
PD CEN/TR 16950:2016 Ductile iron pipes, fittings and accessories. Sanitary characteristics and test methods
UNI EN 12516-4 : 2014 INDUSTRIAL VALVES - SHELL DESIGN STRENGTH - PART 4: CALCULATION METHOD FOR VALVE SHELLS MANUFACTURED IN METALLIC MATERIALS OTHER THAN STEEL
06/30153191 DC : 0 BS EN 15542 - DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - EXTERNAL CEMENT MORTAR COATING FOR PIPES - REQUIREMENTS AND TEST METHODS
DIN EN 15655:2016-07 (Draft) DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - INTERNAL POLYURETHANE LINING FOR PIPES AND FITTINGS - REQUIREMENTS AND TEST METHODS
CEN/TR 16017:2010 Guide to the use of EN 598
I.S. EN 1563:2011 FOUNDING - SPHEROIDAL GRAPHITE CAST IRONS
15/30322070 DC : 0 BS EN 1563 - FOUNDING - SPHEROIDAL GRAPHITE CAST IRONS
S.R. CEN/TR 16470:2013 ENVIRONMENTAL ASPECTS OF DUCTILE IRON PIPE SYSTEMS FOR WATER AND SEWERAGE APPLICATIONS
UNI CEN/TR 15545 : 2007 GUIDE TO THE USE OF EN 545
DIN EN 12502-5 E : 2005 PROTECTION OF METALLIC MATERIALS AGAINST CORROSION - GUIDANCE ON THE ASSESSMENT OF CORROSION LIKELIHOOD IN WATER DISTRIBUTION AND STORAGE SYSTEMS - PART 5: INFLUENCING FACTORS FOR CAST IRON, UNALLOYED AND LOW-ALLOY STEELS
BS EN 14525:2004 Ductile iron wide tolerance couplings and flange adaptors for use with pipes of different materials: ductile iron, grey iron, steel, PVC-U, PE, fibre-cement
BS EN 14901:2006 Ductile iron pipes, fittings and accessories. Epoxy coating (heavy duty) of ductile iron fittings and accessories. Requirements and test methods
BS EN 14628:2005 Ductile iron pipes, fittings and accessories. External polythene coating for pipes. Requirements and test methods
I.S. EN 14901:2014 DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - EPOXY COATING (HEAVY DUTY) OF DUCTILE IRON FITTINGS AND ACCESSORIES - REQUIREMENTS AND TEST METHODS
CEN/TR 1295-2:2005 Structural design of buried pipelines under various conditions of loading - Part 2: Summary of nationally established methods of design
EN 1092-2:1997 Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 2: Cast iron flanges
DIN EN 12502-5:2005-03 PROTECTION OF METALLIC MATERIALS AGAINST CORROSION - GUIDANCE ON THE ASSESSMENT OF CORROSION LIKELIHOOD IN WATER DISTRIBUTION AND STORAGE SYSTEMS - PART 5: INFLUENCING FACTORS FOR CAST IRON, UNALLOYED AND LOW-ALLOY STEELS
DIN EN 15189:2007-02 Ductile iron pipes, fittings and accessories - External polyurethane coating for pipes - Requirements and test methods
ÖNORM EN 14525:2023 01 01 Ductile iron and steel wide tolerance couplings and flange adaptors for use with pipes of different materials: ductile iron, Grey iron, steel, PVC-U, PVC-O, PE, fibre-cement
DIN 28601:2000-06 DUCTILE IRON PIPES AND FITTINGS - SCREWED SOCKET JOINTS - ASSEMBLY, SOCKETS, SCREW RINGS, SEALING RINGS AND SLIP RINGS
05/30131069 DC : DRAFT MAR 2005 EN 598:2005 - DUCTILE IRON PIPES, FITTINGS, ACCESSORIES AND THEIR JOINTS FOR SEWERAGE APPLICATIONS - REQUIREMENTS AND TEST METHODS
PD CEN/TR 15545:2006 Guide to the use of EN 545
16/30339483 DC : 0 BS EN 593 - INDUSTRIAL VALVES - METALLIC BUTTERFLY VALVES FOR GENERAL PURPOSES
DIN 28650:1999-11 DUCTILE IRON FITTINGS - DOUBLE SOCKET 30 DEGREE BENDS, EN-FITTINGS, MI-FITTINGS, IT-FITTINGS - APPLICATION, DIMENSIONS
10/30216654 DC : 0 BS EN 12842 - DUCTILE IRON FITTINGS FOR PVC-U OR PE PIPING SYSTEMS - REQUIREMENTS AND TEST METHODS
UNI EN 15655 : 2009 DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - INTERNAL POLYURETHANE LINING FOR PIPES AND FITTINGS - REQUIREMENTS AND TEST METHODS
DIN EN 15655 E : 2009 DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - INTERNAL POLYURETHANE LINING FOR PIPES AND FITTINGS - REQUIREMENTS AND TEST METHODS
UNI EN 15542 : 2008 DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - EXTERNAL CEMENT MORTAR COATING FOR PIPES - REQUIREMENTS AND TEST METHODS
DIN EN 15542 E : 2008 DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - EXTERNAL CEMENT MORTAR COATING FOR PIPES - REQUIREMENTS AND TEST METHODS
11/30249111 DC : 0 BS EN 12516-4 - INDUSTRIAL VALVES - SHELL DESIGN STRENGTH - PART 4: CALCULATION METHOD FOR VALVE SHELLS MANUFACTURED IN METALLIC MATERIALS OTHER THAN STEEL
04/30121907 DC : DRAFT SEP 2004 PREN 14901 - DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - EPOXY COATING OF DUCTILE IRON FITTINGS AND ACCESSORIES (HEAVY DUTY) - REQUIREMENTS AND TEST METHODS
05/30131064 DC : DRAFT MAR 2005 EN 15189:2005 - DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - EXTERNAL POLYURETHANE COATING FOR PIPES - REQUIREMENTS AND TEST METHODS
16/30340626 DC : 0 BS EN 15655 - DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - INTERNAL POLYURETHANE LINING FOR PIPES AND FITTINGS - REQUIREMENTS AND TEST METHODS
I.S. EN 593:2017 INDUSTRIAL VALVES - METALLIC BUTTERFLY VALVES FOR GENERAL PURPOSES
CEN/TR 16470:2013 Environmental aspects of ductile iron pipe systems for water and sewerage applications
UNE-EN 16668:2016 Industrial valves - Requirements and testing for metallic valves as pressure accessories
EN 12516-4:2014 Industrial valves - Shell design strength - Part 4: Calculation method for valve shells manufactured in metallic materials other than steel
UNI EN 1563 : 2012 FOUNDING - SPHEROIDAL GRAPHITE CAST IRONS
EN 1563:2011 Founding - Spheroidal graphite cast irons
DIN EN 12516-4:2015-01 INDUSTRIAL VALVES - SHELL DESIGN STRENGTH - PART 4: CALCULATION METHOD FOR VALVE SHELLS MANUFACTURED IN METALLIC MATERIALS OTHER THAN STEEL
DIN EN 1171:2015-11 INDUSTRIAL VALVES - CAST IRON GATE VALVES
DIN EN 12842:2012-11 Ductile iron fittings for PVC-U or PE piping systems - Requirements and test methods
DIN EN 14901 E : 2014 DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - EPOXY COATING (HEAVY DUTY) OF DUCTILE IRON FITTINGS AND ACCESSORIES - REQUIREMENTS AND TEST METHODS
DIN EN 598:2009-10 Ductile iron pipes, fittings, accessories and their joints for sewerage applications - Requirements and test methods (includes Amendment A1:2009)
BS EN 598 : 2007 DUCTILE IRON PIPES, FITTINGS, ACCESSORIES AND THEIR JOINTS FOR SEWERAGE APPLICATIONS - REQUIREMENTS AND TEST METHODS
DIN EN 14901:2014-12 DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - EPOXY COATING (HEAVY DUTY) OF DUCTILE IRON FITTINGS AND ACCESSORIES - REQUIREMENTS AND TEST METHODS
I.S. EN 1171:2015 INDUSTRIAL VALVES - CAST IRON GATE VALVES
I.S. EN 598:2007 DUCTILE IRON PIPES, FITTINGS, ACCESSORIES AND THEIR JOINTS FOR SEWERAGE APPLICATIONS - REQUIREMENTS AND TEST METHODS
I.S. EN 12842:2012 DUCTILE IRON FITTINGS FOR PVC-U OR PE PIPING SYSTEMS - REQUIREMENTS AND TEST METHODS
I.S. EN 969:2009 DUCTILE IRON PIPES, FITTINGS, ACCESSORIES AND THEIR JOINTS FOR GAS PIPELINES - REQUIREMENTS AND TEST METHODS
I.S. EN 14628:2005 DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - EXTERNAL POLYETHYLENE COATING FOR PIPES - REQUIREMENTS AND TEST METHODS
I.S. EN 1092-2:1997 FLANGES AND THEIR JOINTS - CIRCULAR FLANGES FOR PIPES, VALVES, FITTINGS AND ACCESSORIES, PN DESIGNATED - PART 2: CAST IRON FLANGES
DIN EN 1563:2015-07 (Draft) FOUNDING - SPHEROIDAL GRAPHITE CAST IRONS
PREN 12842 : DRAFT 2010 DUCTILE IRON FITTINGS FOR PVC-U OR PE PIPING SYSTEMS - REQUIREMENTS AND TEST METHODS
DIN 30674-3:2001-03 SHEATHING DUCTILE CAST IRON PIPES - PART 3: ZINC COATING WITH PROTECTIVE SHEATHING
02/710115 DC : DRAFT AUG 2002 PREN 14525 - DUCTILE IRON WIDE TOLERANCE COUPLINGS AND FLANGE ADAPTORS FOR USE WITH PIPES OF DIFFERENT MATERIALS: DUCTILE IRON, GREY IRON, STEEL, PVC-U PE, FIBRE-CEMENT
PREN 12516-4 : DRAFT 2011 INDUSTRIAL VALVES - SHELL DESIGN STRENGTH - PART 4: CALCULATION METHOD FOR VALVE SHELLS MANUFACTURED IN METALLIC MATERIALS OTHER THAN STEEL
07/19990369 DC : 0 BS EN 806-4 - SPECIFICATIONS FOR INSTALLATIONS INSIDE BUILDINGS CONVEYING WATER FOR HUMAN CONSUMPTION - PART 4 - INSTALLATION
UNI EN 806-4 : 2010 SPECIFICATIONS FOR INSTALLATIONS INSIDE BUILDINGS CONVEYING WATER FOR HUMAN CONSUMPTION - PART 4: INSTALLATION
BS EN 806-4:2010 Specifications for installations inside buildings conveying water for human consumption Installation
S.R. CEN/TR 16950:2016 DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - SANITARY CHARACTERISTICS AND TEST METHODS
PREN 15655 : DRAFT 2016 DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - INTERNAL POLYURETHANE LINING FOR PIPES AND FITTINGS - REQUIREMENTS AND TEST METHODS
NF EN 806-4 : 2010 SPECIFICATIONS FOR INSTALLATIONS INSIDE BUILDINGS CONVEYING WATER FOR HUMAN CONSUMPTION - PART 4: INSTALLATION
BS EN 16668 : 2016 INDUSTRIAL VALVES - REQUIREMENTS AND TESTING FOR METALLIC VALVES AS PRESSURE ACCESSORIES
I.S. EN 15655:2009 DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - INTERNAL POLYURETHANE LINING FOR PIPES AND FITTINGS - REQUIREMENTS AND TEST METHODS
DIN EN 14525 E : 2005 DUCTILE IRON WIDE TOLERANCE COULINGS AND FLANGE ADAPTORS FOR USE WITH PIPES OF DIFFERENT MATERIALS: DUCTILE IRON, GREY IRON, STEEL, PVC-U, PE, FIBRE-CEMENT
DIN EN 14628 E : 2006 DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - EXTERNAL POLYETHYLENE COATING FOR PIPES - REQUIREMENTS AND TEST METHODS
BS EN 969:2009 Ductile iron pipes, fittings, accessories and their joints for gas pipelines. Requirements and test methods
UNE-EN 12842:2013 Ductile iron fittings for PVC-U or PE piping systems - Requirements and test methods
UNI EN 14525 : 2005 DUCTILE IRON WIDE TOLERANCE COUPLINGS AND FLANGE ADAPTORS FOR USE WITH PIPES OF DIFFERENT MATERIALS: DUCTILE IRON, GREY IRON, STEEL, PVC-U PE, FIBRE-CEMENT
UNI EN 15189 : 2007 DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - EXTERNAL POLYURETHANE COATING FOR PIPES - REQUIREMENTS AND TEST METHODS
UNI EN 969 : 2009 DUCTILE IRON PIPES, FITTINGS, ACCESSORIES AND THEIR JOINTS FOR GAS PIPELINES - REQUIREMENTS AND TEST METHODS
UNI EN 12842 : 2012 DUCTILE IRON FITTINGS FOR PVC-U OR PE PIPING SYSTEMS - REQUIREMENTS AND TEST METHODS
I.S. EN 14525:2005 DUCTILE IRON WIDE TOLERANCE COUPLINGS AND FLANGE ADAPTORS FOR USE WITH PIPES OF DIFFERENT MATERIALS: DUCTILE IRON, GREY IRON, STEEL, PVC-U PE, FIBRE-CEMENT
UNI EN 14901 : 2014 DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - EPOXY COATING (HEAVY DUTY) OF DUCTILE IRON FITTINGS AND ACCESSORIES - REQUIREMENTS AND TEST METHODS
BS EN 1171:2015 Industrial valves. Cast iron gate valves
UNI EN 598 : 2009 DUCTILE IRON PIPES, FITTINGS, ACCESSORIES AND THEIR JOINTS FOR SEWERAGE APPLICATIONS - REQUIREMENTS AND TEST METHODS
CEN/TR 16950:2016 Ductile iron pipes, fittings and accessories - Sanitary characteristics and test methods
DIN EN 15542:2008-06 Ductile iron pipes, fittings and accessories - External cement mortar coating for pipes - Requirements and test methods
14/30282872 DC : 0 BS EN 1171 - INDUSTRIAL VALVES - CAST IRON GATE VALVES
13/30287824 DC : 0 BS EN 16668 - INDUSTRIAL VALVES - REQUIREMENTS AND TESTING FOR METALLIC VALVES AS PRESSURE ACCESSORIES
00/708210 DC : DRAFT MAY 2000 ISO/DIS 1071 - WELDING CONSUMABLES - WELDING CONSUMABLES FOR FUSION WELDING OF CAST IRON - CLASSIFICATION
I.S. EN 12516-4:2014 INDUSTRIAL VALVES - SHELL DESIGN STRENGTH - PART 4: CALCULATION METHOD FOR VALVE SHELLS MANUFACTURED IN METALLIC MATERIALS OTHER THAN STEEL
PREN 593 : DRAFT 2016 INDUSTRIAL VALVES - METALLIC BUTTERFLY VALVES FOR GENERAL PURPOSES
DIN EN 806-4:2010-06 Specifications for installations inside buildings conveying water for human consumption - Part 4: Installation
07/30156488 DC : 0 EN 15655 - DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - INTERNAL POLYURETHANE LINING FOR PIPES AND FITTINGS - REQUIREMENTS AND TEST METHODS
BS EN 15655:2009 Ductile iron pipes, fittings and accessories. Internal polyurethane lining for pipes and fittings. Requirements and test methods
BS EN 15542:2008 Ductile iron pipes, fittings and accessories. External cement mortar coating for pipes. Requirements and test methods
DIN 28603:2002-05 DUCTILE IRON PIPES AND FITTINGS - PUSH-IN JOINTS - SURVEY, SOCKETS AND GASKETS
UNE-EN 12516-4:2016 Industrial valves - Shell design strength - Part 4: Calculation method for valve shells manufactured in metallic materials other than steel
PREN 14901 : DRAFT 2014 DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - EPOXY COATING (HEAVY DUTY) OF DUCTILE IRON FITTINGS AND ACCESSORIES - REQUIREMENTS AND TEST METHODS
I.S. EN 806-4:2010 SPECIFICATIONS FOR INSTALLATIONS INSIDE BUILDINGS CONVEYING WATER FOR HUMAN CONSUMPTION - PART 4: INSTALLATION
I.S. EN 15542:2008 DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - EXTERNAL CEMENT MORTAR COATING FOR PIPES - REQUIREMENTS AND TEST METHODS
DIN EN 969:2009-07 DUCTILE IRON PIPES, FITTINGS, ACCESSORIES AND THEIR JOINTS FOR GAS PIPELINES - REQUIREMENTS AND TEST METHODS
DIN EN 15189 E : 2007 DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - EXTERNAL POLYURETHANE COATING FOR PIPES - REQUIREMENTS AND TEST METHODS
PD CEN/TR 1295-2:2005 Structural design of buried pipelines under various conditions of loading Summary of nationally established methods of design
UNE-EN 14901:2015 Ductile iron pipes, fittings and accessories - Epoxy coating (heavy duty) of ductile iron fittings and accessories - Requirements and test methods
BS EN 1503-3:2000 Valves. Materials for bodies, bonnets and covers Cast irons specified in European Standards
BS EN 13397:2002 Industrial valves. Diaphragm valves made of metallic materials
BS EN 15189:2006 Ductile iron pipes, fittings and accessories. External polyurethane coating for pipes. Requirements and test methods
BS EN 806-2:2005 Specifications for installations inside buildings conveying water for human consumption Design
BS EN 12056-2:2000 Gravity drainage systems inside buildings Sanitary pipework, layout and calculation
BS EN 12502-5:2004 Protection of metallic materials against corrosion. Guidance on the assessment of corrosion likelihood in water distribution and storage systems Influencing factors for cast iron, unalloyed and low alloyed steels
EN 14628:2005 Ductile iron pipes, fittings and accessories - External polyethylene coating for pipes - Requirements and test methods
EN 15189:2006 Ductile iron pipes, fittings and accessories - External polyurethane coating for pipes - Requirements and test methods
EN 1514-1:1997 Flanges and their joints - Dimensions of gaskets for PN-designated flanges - Part 1: Non-metallic flat gaskets with or without inserts
EN 806-2:2005 Specification for installations inside buildings conveying water for human consumption - Part 2: Design
EN 969:2009 Ductile iron pipes, fittings, accessories and their joints for gas pipelines - Requirements and test methods
EN 14525:2004 Ductile iron wide tolerance couplings and flange adaptors for use with pipes of different materials: ductile iron, Grey iron, Steel, PVC-U PE, Fibre-cement
EN 806-4:2010 Specifications for installations inside buildings conveying water for human consumption - Part 4: Installation
EN 12502-5 : 2004 PROTECTION OF METALLIC MATERIALS AGAINST CORROSION - GUIDANCE ON THE ASSESSMENT OF CORROSION LIKELIHOOD IN WATER DISTRIBUTION AND STORAGE SYSTEMS - PART 5: INFLUENCING FACTORS FOR CAST IRON, UNALLOYED AND LOW ALLOYED STEELS
EN 12842:2012 Ductile iron fittings for PVC-U or PE piping systems - Requirements and test methods
EN 598:2007+A1:2009 Ductile iron pipes, fittings, accessories and their joints for sewerage applications - Requirements and test methods
EN 1503-3:2000/AC:2001 VALVES - MATERIALS FOR BODIES, BONNETS AND COVERS - PART 3: CAST IRONS SPECIFIED IN EUROPEAN STANDARDS
EN 15542:2008 Ductile iron pipes, fittings and accessories - External cement mortar coating for pipes - Requirements and test methods
EN 593:2017 Industrial valves - Metallic butterfly valves for general purposes
EN 14901:2014 Ductile iron pipes, fittings and accessories - Epoxy coating (heavy duty) of ductile iron fittings and accessories - Requirements and test methods
I.S. CEN TR 15545:2006 GUIDE TO THE USE OF EN 545
PD CEN/TR 16017:2010 Guide to the use of EN 598
PREN 1563 : DRAFT 2015 FOUNDING - SPHEROIDAL GRAPHITE CAST IRONS
PD CEN/TR 16470:2013 Environmental aspects of ductile iron pipe systems for water and sewerage applications
DIN 14244:2003-07 Water suction connection for fire fighting - Under and above ground
BS EN 1563:2011 Founding. Spheroidal graphite cast irons
UNI EN 806-2 : 2008 SPECIFICATION FOR INSTALLATIONS INSIDE BUILDINGS CONVEYING WATER FOR HUMAN CONSUMPTION - PART 2: DESIGN
BS EN 12516-4 : 2014 INDUSTRIAL VALVES - SHELL DESIGN STRENGTH - PART 4: CALCULATION METHOD FOR VALVE SHELLS MANUFACTURED IN METALLIC MATERIALS OTHER THAN STEEL
S.R. CEN/TR 16017:2010 GUIDE TO THE USE OF EN 598
17/30362692 DC : 0 BS EN 598 - COATED AND LINED DUCTILE IRON PIPES, FITTINGS AND THEIR JOINTS FOR SEWERAGE AND DRAINAGE APPLICATIONS - PRODUCTS CHARACTERISTICS AND TEST AND ASSESSMENT METHODS
CEN/TR 15545:2006 Guide to the use of EN 545
EN 15655:2009 Ductile iron pipes, fittings and accessories - Internal polyurethane lining for pipes and fittings - Requirements and test methods
DIN EN 1514-1:1997-08 FLANGES AND THEIR JOINTS - DIMENSIONS OF GASKET FOR PN-DESIGNATED FLANGES - PART 1: NON-METALLIC FLAT GASKETS WITH OR WITHOUT INSERTS
DIN EN 13397:2002-03 INDUSTRIAL VALVES - DIAPHRAGM VALVES MADE OF METALLIC MATERIALS
DIN EN 806-2:2005-06 Specification for installations inside buildings conveying water for human consumption - Part 2: Design
UNE-EN 1171:2016 Industrial valves - Cast iron gate valves
BS EN 12842:2012 Ductile iron fittings for PVC-U or PE piping systems. Requirements and test methods
EN 13397:2001 Industrial valves - Diaphragm valves made of metallic materials
EN 1171:2015 Industrial valves - Cast iron gate valves
DIN EN 14525:2005-02 Ductile iron wide tolerance couplings and flange adaptors for use with pipes of different materials: Ductile iron, grey iron, steel, PVC-U, PE, fibre-cement
DIN EN 14628:2006-01 DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - EXTERNAL POLYETHYLENE COATING FOR PIPES - REQUIREMENTS AND TEST METHODS

EN 15189:2006 Ductile iron pipes, fittings and accessories - External polyurethane coating for pipes - Requirements and test methods
EN ISO 6506-1:2014 Metallic materials - Brinell hardness test - Part 1: Test method (ISO 6506-1:2014)
ISO 6506-1:2014 Metallic materials Brinell hardness test Part 1: Test method
ISO/IEC Guide 62:1996 General requirements for bodies operating assessment and certification/registration of quality systems
EN ISO 7091 : 2000 PLAIN WASHERS - NORMAL SERIES - PRODUCT GRADE C
EN 197-1:2011 Cement - Part 1: Composition, specifications and conformity criteria for common cements
EN 681-1:1996/A3:2005 ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 1: VULCANIZED RUBBER
EN 14525:2004 Ductile iron wide tolerance couplings and flange adaptors for use with pipes of different materials: ductile iron, Grey iron, Steel, PVC-U PE, Fibre-cement
EN ISO 6892-1:2016 Metallic materials - Tensile testing - Part 1: Method of test at room temperature (ISO 6892-1:2016)
ISO 4016:2011 Hexagon head bolts Product grade C
ISO 4034:2012 Hexagon regular nuts (style 1) Product grade C
89/106/EEC : 1988 COUNCIL DIRECTIVE OF 21 DECEMBER 1988 ON THE APPROXIMATION OF LAWS, REGULATIONS AND ADMINISTRATIVE PROVISIONS OF THE MEMBER STATES RELATING TO CONSTRUCTION PRODUCTS
EN 805:2000 Water supply - Requirements for systems and components outside buildings
EN 45011:1998 General requirements for bodies operating product certification systems (ISO/IEC Guide 65:1996)
ISO 6892-1:2016 Metallic materials Tensile testing Part 1: Method of test at room temperature
EN ISO 4016:2011 Hexagon head bolts - Product grade C (ISO 4016:2011)
ISO 6708:1995 Pipework components Definition and selection of DN (nominal size)
EN 45011 : 1998 GENERAL REQUIREMENTS FOR BODIES OPERATING PRODUCT CERTIFICATION SYSTEMS
EN ISO 4034:2012/AC:2013 HEXAGON REGULAR NUTS (STYLE 1) - PRODUCT GRADE C (ISO 4034:2012/COR 1:2013)
EN 196-1:2016 Methods of testing cement - Part 1: Determination of strength
EN ISO 6708:1995 Pipework components - Definition and selection of DN (nominal size) (ISO 6708:1995)
EN ISO 9001:2015 Quality management systems - Requirements (ISO 9001:2015)
ISO 7091:2000 Plain washers Normal series Product grade C
EN 1333:2006 Flanges and their joints - Pipework components - Definition and selection of PN
ISO 9001:2015 Quality management systems — Requirements
EN 15542:2008 Ductile iron pipes, fittings and accessories - External cement mortar coating for pipes - Requirements and test methods
ISO/IEC Guide 65:1996 General requirements for bodies operating product certification systems
EN 10310:2003 Steel tubes and fittings for onshore and offshore pipelines - Internal and external polyamide powder based coatings
EN 1092-2:1997 Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 2: Cast iron flanges
EN 45012 : 1998 GENERAL REQUIREMENTS FOR BODIES OPERATING ASSESSMENT AND CERTIFICATION/REGISTRATION OF QUALITY SYSTEMS
EN 14901:2014 Ductile iron pipes, fittings and accessories - Epoxy coating (heavy duty) of ductile iron fittings and accessories - Requirements and test methods
EN 15655:2009 Ductile iron pipes, fittings and accessories - Internal polyurethane lining for pipes and fittings - Requirements and test methods
ISO 2531:2009 Ductile iron pipes, fittings, accessories and their joints for water applications
EN 14628:2005 Ductile iron pipes, fittings and accessories - External polyethylene coating for pipes - Requirements and test methods

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more