Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

EN 60793-1-41:2010

Current
Current

The latest, up-to-date edition.

Optical fibres - Part 1-41: Measurement methods and test procedures - Bandwidth
Published date

08-10-2010

FOREWORD
1 Scope
2 Normative references
3 Terms and definitions
4 Apparatus
5 Sampling and specimens
6 Procedure
7 Calculations or interpretation of results
8 Length normalization
9 Results
10 Specification information
Annex A (normative) - Intramodal dispersion factor and the normalized
        intermodal dispersion limit
Annex B (normative) - Fibre transfer function, H(f), power spectrum,
        [H(f)], and f[3 dB]
Annex C (normative) - Calculations for other reporting methods
Annex D (normative) - Mode scrambler requirements for overfilled
        launching conditions to multimode fibres
Annex ZA (normative) - Normative references to international
         publications with their corresponding European
         publications
Bibliography

IEC 60793-1-41:2010 describes three methods for determining and measuring the modal bandwidth of multimode optical fibres (see IEC 60793-2-10, IEC 60793-30 series and IEC 60793-40 series). The baseband frequency response is directly measured in the frequency domain by determining the fibre response to a sinusoidaly modulated light source. The baseband response can also be measured by observing the broadening of a narrow pulse of light. The calculated response is determined using differential mode delay (DMD) data. The three methods are: - Method A - Time domain (pulse distortion) measurement - Method B - Frequency-domain measurement - Method C - Overfilled launch modal bandwidth calculated from differential mode delay (OMBc). The main change with respect to the previous edition is the addition of a third method for determining modal bandwidth based on DMD data and to improve measurement procedures for A4 fibres. This standard should be read in conjunction with IEC 60793-1-1 and IEC 60793-1-2, which cover generic specifications.

Committee
CLC/TC 86A
DevelopmentNote
Partially supersedes EN 188000. (06/2002) To be read in conjunction with EN 60793-1-1. (01/2004) To be read in conjunction with IEC 60793-1-2. (10/2010) Supersedes UNE EN 188000. (01/2012)
DocumentType
Standard
PublisherName
European Committee for Standards - Electrical
Status
Current
Supersedes

09/30215019 DC : 0 BS EN 50551-1 - SIMPLEX AND DUPLEX CABLES TO BE USED FOR CORDS - PART 1: BLANK DETAIL SPECIFICATION AND MINIMUM REQUIREMENTS
I.S. EN 60793-2-10:2017 OPTICAL FIBRES - PART 2-10: PRODUCT SPECIFICATIONS - SECTIONAL SPECIFICATION FOR CATEGORY A1 MULTIMODE FIBRE
BS EN 60793-2-40:2016 Optical fibres Product specifications. Sectional specification for category A4 multimode fibres
BS EN 60793-2-20:2016 Optical fibres Product specifications. Sectional specification for category A2 multimode fibres
I.S. EN 60793-1-49:2006 OPTICAL FIBRES - PART 1-49: MEASUREMENT METHODS AND TEST PROCEDURES - DIFFERENTIAL MODE DELAY
BS EN 50551-1:2011 Simplex and duplex cables to be used for cords Blank detail specification and minimum requirements
NF EN 50551-1 : 2011 SIMPLEX AND DUPLEX CABLES TO BE USED FOR CORDS - PART 1: BLANK DETAIL SPECIFICATION AND MINIMUM REQUIREMENTS
I.S. EN 50551-1:2011 SIMPLEX AND DUPLEX CABLES TO BE USED FOR CORDS - PART 1: BLANK DETAIL SPECIFICATION AND MINIMUM REQUIREMENTS
EN 60793-2-30:2015 Optical fibres - Part 2-30: Product specifications - Sectional specification for category A3 multimode fibres
EN 60794-2-41 : 2008 OPTICAL FIBRE CABLES - PART 2-41: INDOOR CABLES - PRODUCT SPECIFICATION FOR SIMPLEX AND DUPLEX BUFFERED A4 FIBRES
EN 60793-1-1:2017 Optical fibres - Part 1-1: Measurement methods and test procedures - General and guidance
EN 60793-2-20:2016 Optical fibres - Part 2-20: Product specifications - Sectional specification for category A2 multimode fibres
EN 60793-1-49:2006 OPTICAL FIBRES - PART 1-49: MEASUREMENT METHODS AND TEST PROCEDURES - DIFFERENTIAL MODE DELAY
EN 61280-1-4:2010 Fibre optic communication subsystem test procedures - Part 1-4: General communication subsystems - Light source encircled flux measurement method
06/30150101 DC : 0 EN 3745-303 - AEROSPACE SERIES - FIBRES AND CABLES, OPTICAL, AIRCRAFT USE - TEST METHODS - PART 303: BANDWIDTH
UNE-EN 60793-1-1:2017 Optical fibres - Part 1-1: Measurement methods and test procedures - General and guidance
CEI EN 60793-1-49 : 2007 OPTICAL FIBRES - PART 1-49: MEASUREMENT METHODS AND TEST PROCEDURES - DIFFERENTIAL MODE DELAY
CEI EN 60793-1-42 : 2014 OPTICAL FIBRES - PART 1-42: MEASUREMENT METHODS AND TEST PROCEDURES - CHROMATIC DISPERSION
I.S. EN 60794-1-20:2014 OPTICAL FIBRE CABLES - PART 1-20: GENERIC SPECIFICATION - BASIC OPTICAL CABLE TEST PROCEDURES - GENERAL AND DEFINITIONS
BS EN 61280-1-4:2010 Fibre optic communication subsystem test procedures General communication subsystems. Light source encircled flux measurement method
UNE-EN 60794-1-20:2014 Optical fibre cables - Part 1-20: Generic specification - Basic optical cable test procedures - General and definitions
I.S. EN 50173-1:2011 INFORMATION TECHNOLOGY - GENERIC CABLING SYSTEMS - PART 1: GENERAL REQUIREMENTS
BS EN 60794-1-20:2014 Optical fibre cables Generic specification. Basic optical cable test procedures. General and definitions
CEI EN 50551-1 : 2012 SIMPLEX AND DUPLEX CABLES TO BE USED FOR CORDS - PART 1: BLANK DETAIL SPECIFICATION AND MINIMUM REQUIREMENTS
BS EN 60793-2-30:2015 Optical fibres Product specifications. Sectional specification for category A3 multimode fibres
CEI EN 50173-1 : 2011 INFORMATION TECHNOLOGY - GENERIC CABLING SYSTEMS - PART 1: GENERAL REQUIREMENTS
BS EN 50173-1:2011 Information technology. Generic cabling systems General requirements
CEI EN 60793-2-30 : 2016 OPTICAL FIBRES - PART 2-30: PRODUCT SPECIFICATIONS - SECTIONAL SPECIFICATION FOR CATEGORY A3 MULTIMODE FIBRES
EN 50173-1:2011 Information technology - Generic cabling systems - Part 1: General requirements
BS EN 60793-1-49:2006 Optical fibres Measurement methods and test procedures - Differential mode delay
BS EN 60793-1-1:2017 Optical fibres Measurement methods and test procedures. General and guidance
CEI EN 60793-1-1 : 2010 OPTICAL FIBRES - PART 1-1: MEASUREMENT METHODS AND TEST PROCEDURES - GENERAL AND GUIDANCE
BS EN 60793-1-42:2013 Optical fibres Measurement methods and test procedures. Chromatic dispersion
I.S. EN 60793-1-42:2013 OPTICAL FIBRES - PART 1-42: MEASUREMENT METHODS AND TEST PROCEDURES - CHROMATIC DISPERSION (IEC 60793-1-42:2013 (EQV))
I.S. EN 60793-2-30:2015 OPTICAL FIBRES - PART 2-30: PRODUCT SPECIFICATIONS - SECTIONAL SPECIFICATION FOR CATEGORY A3 MULTIMODE FIBRES
EN 60793-2-10:2017 Optical fibres - Part 2-10: Product specifications - Sectional specification for category A1 multimode fibres
EN 60793-1-42:2013/AC:2013 OPTICAL FIBRES - PART 1-42: MEASUREMENT METHODS AND TEST PROCEDURES - CHROMATIC DISPERSION
BS EN 3745-303:2007 Aerospace series. Fibres and cables, optical, aircraft use. Test methods Bandwidth
EN 3745-303:2007 Aerospace series - Fibres and cables, optical, aircraft use - Test methods - Part 303: Bandwidth
EN 60793-2-40:2016 Optical fibres - Part 2-40: Product specifications - Sectional specification for category A4 multimode fibres
BS EN 60793-2-10:2017 Optical fibres Product specifications. Sectional specification for category A1 multimode fibres
BS EN 60794-2-41:2008 Optical fibre cables Indoor cables. Product specification for simplex and duplex buffered A4 fibres
PREN 3745-303 : 200P1 AEROSPACE SERIES - FIBRES AND CABLES, OPTICAL, AIRCRAFT USE - TEST METHODS - PART 303: BANDWIDTH
I.S. EN 60793-2-40:2016 OPTICAL FIBRES - PART 2-40: PRODUCT SPECIFICATIONS - SECTIONAL SPECIFICATION FOR CATEGORY A4 MULTIMODE FIBRES
I.S. EN 60793-1-1:2017 OPTICAL FIBRES - PART 1-1: MEASUREMENT METHODS AND TEST PROCEDURES - GENERAL AND GUIDANCE
EN 60794-1-20:2014 Optical fibre cables - Part 1-20: Generic specification - Basic optical cable test procedures - General and definitions
EN 50551-1:2011 Simplex and duplex cables to be used for cords - Part 1: Blank Detail Specification and minimum requirements

EN 60793-1-20:2014/AC:2016-03 OPTICAL FIBRES - PART 1-20: MEASUREMENT METHODS AND TEST PROCEDURES - FIBRE GEOMETRY (IEC 60793-1-20:2014/COR1:2016)
IEC 60793-2-10:2017 Optical fibres - Part 2-10: Product specifications - Sectional specification for category A1 multimode fibres
IEC 60793-1-43:2015 Optical fibres - Part 1-43: Measurement methods and test procedures - Numerical aperture measurement
IEC 60793-2-30:2015 Optical fibres - Part 2-30: Product specifications - Sectional specification for category A3 multimode fibres
IEC 60793-2-40:2015 Optical fibres - Part 2-40: Product specifications - Sectional specification for category A4 multimode fibres
IEC 60793-1-42:2013 Optical fibres - Part 1-42: Measurement methods and test procedures - Chromatic dispersion
IEC 60793-1-49:2006 Optical fibres - Part 1-49: Measurement methods and test procedures - Differential mode delay
EN 60793-1-49:2006 OPTICAL FIBRES - PART 1-49: MEASUREMENT METHODS AND TEST PROCEDURES - DIFFERENTIAL MODE DELAY
EN 60793-1-43:2015 Optical fibres - Part 1-43: Measurement methods and test procedures - Numerical aperture measurement
IEC 60793-1-20:2014 Optical fibres - Part 1-20: Measurement methods and test procedures - Fibre geometry
EN 60793-1-42:2013/AC:2013 OPTICAL FIBRES - PART 1-42: MEASUREMENT METHODS AND TEST PROCEDURES - CHROMATIC DISPERSION

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more