EN 60987:2015
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Nuclear power plants - Instrumentation and control important to safety - Hardware design requirements for computer-based systems
Superseded date
25-09-2021
Published date
20-02-2015
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Project structure
5 Hardware requirements
6 Design and development
7 Verification and validation
8 Qualification
9 Manufacture
10 Installation and commissioning
11 Maintenance
12 Modification
13 Operation
Annex A (informative) - Overview of system life cycle
Annex B (informative) - Outline of qualification
Annex C (informative) - Example of maintenance procedure
Bibliography
Annex ZA (normative) - Normative references to international
publications with their corresponding European
publications
Is applicable to computer-system hardware for systems of Class 1 and 2 (as defined by IEC 61513) in nuclear power plants. This new edition reflects recent developments in computer system hardware design, the use of pre-developed hardware and changes in terminology.
| Committee |
CLC/TC 45AX
|
| DocumentType |
Standard
|
| PublisherName |
European Committee for Standards - Electrical
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| I.S. EN IEC 60987:2021 | Identical |
| SN EN 60987:2015 | Identical |
| DIN EN 60987 : 2015 | Identical |
| IEC 60987:2007+AMD1:2013 CSV | Identical |
| NF EN 60987 : 2015 | Identical |
| PN EN 60987 : 2015 | Identical |
| NEN EN IEC 60987 : 2015 | Identical |
| I.S. EN 60987:2015 | Identical |
| VDE 0491-3-1 : 2015 | Identical |
| CEI EN 60987 : 2015 | Identical |
| BS EN 60987:2015 | Identical |
| NBN EN 60987 : 2015 | Identical |
| OVE/ONORM EN 60987 : 2015 | Identical |
| UNE-EN 60987:2015 | Identical |
| BS EN 61226:2010 | Nuclear power plants. Instrumentation and control important to safety. Classification of instrumentation and control functions |
| EN 60671:2011 | Nuclear power plants - Instrumentation and control systems important to safety - Surveillance testing |
| EN 62566:2014 | Nuclear power plants - Instrumentation and control important to safety - Development of HDL-programmed integrated circuits for systems performing category A functions |
| BS EN 61513:2013 | Nuclear power plants. Instrumentation and control important to safety. General requirements for systems |
| BS EN 60671:2011 | Nuclear power plants. Instrumentation and control systems important to safety. Surveillance testing |
| EN 61226:2010 | Nuclear power plants - Instrumentation and control important to safety - Classification of instrumentation and control functions |
| KTA 3505 : 2015(R2017) | TYPE TESTING OF MEASURING SENSORS AND TRANSDUCERS OF THE INSTRUMENTATION AND CONTROL SYSTEM IMPORTANT TO SAFETY |
| CEI EN 60671 : 2012 | NUCLEAR POWER PLANTS - INSTRUMENTATION AND CONTROL SYSTEMS IMPORTANT TO SAFETY - SURVEILLANCE TESTING |
| I.S. EN 60671:2011 | NUCLEAR POWER PLANTS - INSTRUMENTATION AND CONTROL SYSTEMS IMPORTANT TO SAFETY - SURVEILLANCE TESTING |
| BS EN 62566:2014 | Nuclear power plants. Instrumentation and control important to safety. Development of HDL-programmed integrated circuits for systems performing category A functions |
| CEI EN 61500 : 2012 | NUCLEAR POWER PLANTS - INSTRUMENTATION AND CONTROL IMPORTANT TO SAFETY - DATA COMMUNICATION IN SYSTEMS PERFORMING CATEGORY A FUNCTIONS |
| CEI EN 61513 : 2013 | NUCLEAR POWER PLANTS - INSTRUMENTATION AND CONTROL IMPORTANT TO SAFETY - GENERAL REQUIREMENT FOR SYSTEMS |
| I.S. EN 61226:2010 | NUCLEAR POWER PLANTS - INSTRUMENTATION AND CONTROL IMPORTANT TO SAFETY - CLASSIFICATION OF INSTRUMENTATION AND CONTROL FUNCTIONS |
| BS EN 61500:2011 | Nuclear power plants. Instrumentation and control important to safety. Data communication in systems performing category A functions |
| EN 61500:2011 | Nuclear power plants - Instrumentation and control important to safety - Data communication in systems performing category A functions |
| I.S. EN 62566:2014 | NUCLEAR POWER PLANTS - INSTRUMENTATION AND CONTROL IMPORTANT TO SAFETY - DEVELOPMENT OF HDL-PROGRAMMED INTEGRATED CIRCUITS FOR SYSTEMS PERFORMING CATEGORY A FUNCTIONS |
| I.S. EN 61500:2011 | NUCLEAR POWER PLANTS - INSTRUMENTATION AND CONTROL IMPORTANT TO SAFETY - DATA COMMUNICATION IN SYSTEMS PERFORMING CATEGORY A FUNCTIONS |
| I.S. EN 61513:2013 | NUCLEAR POWER PLANTS - INSTRUMENTATION AND CONTROL IMPORTANT TO SAFETY - GENERAL REQUIREMENTS FOR SYSTEMS (IEC 61513:2011 (EQV)) |
| EN 61513:2013 | Nuclear power plants - Instrumentation and control important to safety - General requirements for systems |
| IEC 61025:2006 | Fault tree analysis (FTA) |
| EN 60812:2006 | Analysis techniques for system reliability - Procedure for failure mode and effects analysis (FMEA) |
| ISO 3951-1:2013 | Sampling procedures for inspection by variables — Part 1: Specification for single sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection for a single quality characteristic and a single AQL |
| EN 22768-2:1993 | General tolerances - Part 2: Geometrical tolerances for features without individual tolerance indications (ISO 2768-2:1989) |
| IEC 61226:2009 | Nuclear power plants - Instrumentation and control important to safety - Classification of instrumentation and control functions |
| IEC 60812:2006 | Analysis techniques for system reliability - Procedure for failure mode and effects analysis (FMEA) |
| IEC 62138:2004 | Nuclear power plants - Instrumentation and control important for safety - Software aspects for computer-based systems performing category B or C functions |
| EN 62138 : 2009 | NUCLEAR POWER PLANTS - INSTRUMENTATION AND CONTROL IMPORTANT FOR SAFETY - SOFTWARE ASPECTS FOR COMPUTER-BASED SYSTEMS PERFORMING CATEGORY B OR C FUNCTIONS |
| EN 60880 : 2009 | NUCLEAR POWER PLANTS - INSTRUMENTATION AND CONTROL SYSTEMS IMPORTANT TO SAFETY - SOFTWARE ASPECTS FOR COMPUTER-BASED SYSTEMS PERFORMING CATEGORY A FUNCTIONS |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| ISO 2768-2:1989 | GENERAL TOLERANCES - PART 2: GEOMETRICAL TOLERANCES FOR FEATURES WITHOUT INDIVIDUAL TOLERANCE INDICATIONS |
| ISO/IEC 12207:2008 | Systems and software engineering Software life cycle processes |
| EN 22768-1:1993 | General tolerances - Part 1: Tolerances for linear and angular dimensions without individual tolerance indications (ISO 2768-1:1989) |
| EN 61025:2007 | Fault tree analysis (FTA) |
| IEC 60880:2006 | Nuclear power plants - Instrumentation and control systems important to safety - Software aspects for computer-based systems performing category A functions |
| ISO 9001:2015 | Quality management systems — Requirements |
| IEC 60780:1998 | Nuclear power plants - Electrical equipment of the safety system - Qualification |
| IEC 61513:2011 | Nuclear power plants - Instrumentation and control important to safety - General requirements for systems |
| ISO 3951-2:2013 | Sampling procedures for inspection by variables — Part 2: General specification for single sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection of independent quality characteristics |
Sorry this product is not available in your region.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.