EN 61000-3-2:2014
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Electromagnetic compatibility (EMC) - Part 3-2: Limits - Limits for harmonic current emissions (equipment input current ≤ 16 A per phase)
Superseded date
02-02-2022
Published date
22-08-2014
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 General
5 Classification of equipment
6 General requirements
7 Harmonic current limits
Annex A (normative) - Measurement circuit and supply source
Annex B (normative) - Requirements for measurement equipment
Annex C (normative) - Type test conditions
Bibliography
Annex ZA (normative) - Normative references to international
publications with their corresponding
European publications
Annex ZZ (informative) - Coverage of Essential Requirements of
EU Directives
IEC 61000-3-2:2014 deals with the limitation of harmonic currents injected into the public supply system. It specifies limits of harmonic components of the input current which may be produced by equipment tested under specified conditions. It is applicable to electrical and electronic equipment having an input current up to and including 16 A per phase, and intended to be connected to public low voltage distribution systems. Arc welding equipment which is not professional equipment, with input current up to and including 16 A per phase, is included in this standard. Arc welding equipment intended for professional use, as specified in IEC 60974-1, is excluded from this standard and may be subject to installation restrictions as indicated in IEC/TR 61000-3-4 or IEC 61000-3-12. The tests according to this standard are type tests. Test conditions for particular equipment are given in Annex C. For systems with nominal voltages less than 220 V (line-to-neutral), the limits have not yet been considered. This fourth edition cancels and replaces the third edition published in 2005, Amendment 1:2008, Amendment 2:2009 and Corrigendum of August 2009. This edition includes the following significant technical changes with respect to the previous edition:- a clarification of the repeatability and reproducibility of measurements;- a more accurate specification of the general test conditions for information technology equipment;- the addition of optional test conditions for information technology equipment with external power supplies or battery chargers;- the addition of a simplified test method for equipment that undergoes minor changes or updates;- an update of the test conditions for washing machines;- a clarification of the requirements for Class C equipment with active input power ≤ 25 W;- an update of the test conditions for audio amplifiers;- a clarification of the test conditions for lamps;- an update of the test conditions for vacuum cleaners;- the addition of test conditions for high pressure cleaners;- an update of the test conditions for arc welding equipment;- the reclassification of refrigerators and freezers with variable-speed drives into Class D;- and the addition of test conditions for refrigerators and freezers.
| DevelopmentNote |
Supersedes EN 60555-2 (05/2001)
|
| DocumentType |
Standard
|
| PublisherName |
European Committee for Standards - Electrical
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| BS EN 61000-3-2:2014 | Identical |
| OVE/ONORM EN 61000-3-2 : 2015 | Identical |
| DIN EN 61000-3-2 : 2015 | Identical |
| NEN EN IEC 61000-3-2 : 2014 | Identical |
| I.S. EN 61000-3-2:2014 | Identical |
| UNE-EN 61000-3-2:2006 | Identical |
| NBN EN 61000 3-2 : 2014 | Identical |
| PN EN 61000-3-2 : 2014 | Identical |
| IEC 61000-3-2 : 4.0 | Identical |
| CEI EN 61000-3-2 : 2015 | Identical |
| SN EN 61000-3-2:2014 | Identical |
| UNE-EN 61000-3-2:2014 | Identical |
| VDE 0838-2 : 2015 | Identical |
| NF EN 61000-3-2 : 2014 | Identical |
| NEN 11000-3-2 : 95 AMD 12 96 | Similar to |
| I.S. EN 50090-2-2:1998 | HOME AND BUILDING ELECTRONIC SYSTEMS (HBES) - PART 2-2: SYSTEM OVERVIEW - GENERAL TECHNICAL REQUIREMENTS |
| I.S. EN 61326-1:2013 | ELECTRICAL EQUIPMENT FOR MEASUREMENT, CONTROL AND LABORATORY USE - EMC REQUIREMENTS - PART 1: GENERAL REQUIREMENTS (IEC 61326-1:2012 (EQV)) |
| CLC/TS 50217:2005 | Guide for in situ measurements - In situ measurement of disturbance emission |
| BS EN 61786-1:2014 | Measurement of DC magnetic, AC magnetic and AC electric fields from 1 Hz to 100 kHz with regard to exposure of human beings Requirements for measuring instruments |
| 09/30193293 DC : DRAFT MAR 2009 | BS EN 12184 - ELECTRICALLY POWERED WHEELCHAIRS, SCOOTERS AND THEIR CHARGERS - REQUIREMENTS AND TEST METHODS |
| I.S. EN 12098-4:2005 | CONTROLS FOR HEATING SYSTEMS - PART 4: OPTIMUM START-STOP CONTROL EQUIPMENT FOR ELECTRICAL SYSTEMS |
| BS EN 50065-2-3:2003 | Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148.5 Khz Immunity requirements for mains communications equipment and systems operating in the range of frequencies 3 kHz to 95 kHz and intended for use by electricity suppliers and distributors |
| BS EN 50240:2004 | Electromagnetic compatibilty (EMC). Product standard for resistance welding equipment |
| 13/30252780 DC : 0 | BS EN 50121-5 - RAILWAY APPLICATIONS - ELECTROMAGNETIC COMPATIBILITY - PART 5: EMISSION AND IMMUNITY OF FIXED POWER SUPPLY INSTALLATIONS AND APPARATUS |
| EN 63002:2017 | Identification and communication interoperability method for external power supplies used with portable computing devices |
| I.S. EN 50564:2011 | ELECTRICAL AND ELECTRONIC HOUSEHOLD AND OFFICE EQUIPMENT - MEASUREMENT OF LOW POWER CONSUMPTION |
| I.S. EN 50065-2-2:2003 | SIGNALLING ON LOW-VOLTAGE ELECTRICAL INSTALLATIONS IN THE FREQUENCY RANGE 3 KHZ TO 148,5 KHZ - PART 2-2: IMMUNITY REQUIREMENTS FOR MAINS COMMUNICATIONS EQUIPMENT AND SYSTEMS OPERATING IN THE RANGE OF FREQUENCIES 95 KHZ TO 148,5 KHZ AND INTENDED FOR USE IN INDUSTRIAL ENVIRONMENTS |
| EG 201 450 : 1.1.1 | GUIDANCE ON THE IDENTIFICATION OF HARMONIZED STANDARDS AND/OR OTHER TECHNICAL SPECIFICATIONS FOR RADIO EQUIPMENT AND TELECOMMUNICATIONS TERMINAL EQUIPMENT (R&TTE) COVERING REQUIREMENTS UNDER ARTICLE 3.1 OF DIRECTIVE 1999/5/EC |
| BS EN 62920:2017 | Photovoltaic power generating systems. EMC requirements and test methods for power conversion equipment |
| NF EN 55103-1 : 2009 AMD 1 2013 | ELECTROMAGNETIC COMPATIBILITY - PRODUCT FAMILY STANDARD FOR AUDIO, VIDEO, AUDIO-VISUAL AND ENTERTAINMENT LIGHTING CONTROL APPARATUS FOR PROFESSIONAL USE - PART 1: EMISSIONS |
| EN 61326-1:2013 | Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 1: General requirements |
| BS EN 62282-3-100:2012 | Fuel cell technologies Stationary fuel cell power systems. Safety |
| I.S. EN 61800-3:2005 | ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 3: EMC REQUIREMENTS AND SPECIFIC TEST METHODS (IEC 61800-3:2004 (EQV)) |
| BS EN 62282-3-1:2007 | Fuel cell technologies Stationary fuel cell power systems. Safety |
| 09/30192323 DC : 0 | BS EN 13637 - BUILDING HARDWARE - ELECTRICALLY CONTROLLED EXIT SYSTEMS FOR USE ON ESCAPE ROUTES - REQUIREMENTS AND TEST METHODS |
| BS EN 50293:2012 | Road traffic signal systems. Electromagnetic compatibility |
| BS EN 60947-5-2 : 2007 | LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 5-2: CONTROL CIRCUIT DEVICES AND SWITCHING ELEMENTS - PROXIMITY SWITCHES |
| BS EN 50107:1998 | Signs and luminous-discharge-tube installations operating from a no-load rated output voltage exceeding 1 kV but not exceeding 10 kV |
| CEI EN 60601-1-2 : 2016 | MEDICAL ELECTRICAL EQUIPMENT - PART 1-2: GENERAL REQUIREMENTS FOR BASIC SAFETY AND ESSENTIAL PERFORMANCE - COLLATERAL STANDARD: ELECTROMAGNETIC DISTURBANCES - REQUIREMENTS AND TESTS |
| EN 60947-5-1:2017 | Low-voltage switchgear and controlgear - Part 5-1: Control circuit devices and switching elements - Electromechanical control circuit devices |
| 99/240940 DC : 0 | BS EN 50331-1 - PHOTOVOLTAIC SYSTEMS IN BUILDINGS - PART 1: SAFETY REQUIREMENTS |
| BS EN 50065-2-2:2003 | Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148,5 kHz Immunity requirements for mains communications equipment and systems operating in the range of frequencies 95 kHz to 148,5 kHz and intended for use in industrial environments |
| BS EN 61000-6-3 : 2007 : INC : AMD 1 : 2011 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-3: GENERIC STANDARDS - EMISSION STANDARD FOR RESIDENTIAL, COMMERCIAL AND LIGHT-INDUSTRIAL ENVIRONMENTS |
| 98/201910 DC : DRAFT APRIL 1998 | PREN 50297 - PHOTOELECTRIC CONTROL UNITS FOR ROAD AND STREET LIGHTING |
| CEI EN 50512 : 2014 | ELECTRICAL INSTALLATIONS FOR LIGHTING AND BEACONING OF AERODROMES - ADVANCED VISUAL DOCKING GUIDANCE SYSTEMS (A-VDGS) |
| PREN 15194 : DRAFT 2015 | CYCLES - ELECTRICALLY POWER ASSISTED CYCLES - EPAC BICYCLES |
| EN 61439-1:2011 | Low-voltage switchgear and controlgear assemblies - Part 1: General rules |
| CEI EN 61000-3-12 : 2012 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 3-12: LIMITS - LIMITS FOR HARMONIC CURRENTS PRODUCED BY EQUIPMENT CONNECTED TO PUBLIC LOW-VOLTAGE SYSTEMS WITH INPUT CURRENT > 16 A AND <= 75 A PER PHASE |
| BS EN 62080 : 2009 | SOUND SIGNALLING DEVICES FOR HOUSEHOLD AND SIMILAR PURPOSES |
| BS EN 61000-6-3 : 2007 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-3: GENERIC STANDARDS - EMISSION STANDARD FOR RESIDENTIAL, COMMERCIAL AND LIGHT-INDUSTRIAL ENVIRONMENTS |
| I.S. EN 55103-1:2009 | ELECTROMAGNETIC COMPATIBILITY - PRODUCT FAMILY STANDARD FOR AUDIO, VIDEO, AUDIO-VISUAL AND ENTERTAINMENT LIGHTING CONTROL APPARATUS FOR PROFESSIONAL USE - PART 1: EMISSIONS |
| CEI EN 50293 : 2013 | ROAD TRAFFIC SIGNAL SYSTEMS - ELECTROMAGNETIC COMPATIBILITY |
| I.S. EN 60974-10:2014 | ARC WELDING EQUIPMENT - PART 10: ELECTROMAGNETIC COMPATIBILITY (EMC) REQUIREMENTS |
| BS EN 60929 : 2011 | AC AND/OR DC-SUPPLIED ELECTRONIC CONTROL GEAR FOR TUBULAR FLUORESCENT LAMPS - PERFORMANCE REQUIREMENTS |
| UNE-EN 50121-5:2018 | Railway applications - Electromagnetic compatibility - Part 5: Emission and immunity of fixed power supply installations and apparatus |
| 17/30358367 DC : 0 | BS EN 17128 - NON-APPROVED LIGHT MOTORIZED VEHICLES FOR THE TRANSPORTATION OF PERSONS AND GOODS AND RELATED FACILITIES - PERSONAL LIGHT ELECTRIC VEHICLES (PLEV) - SAFETY REQUIREMENTS AND TEST METHODS |
| I.S. EN 60947-5-9:2007 | LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 5-9: CONTROL CIRCUIT DEVICES AND SWITCHING ELEMENTS - FLOW RATE SWITCHES |
| NF EN 55103-2 : 2009 | ELECTROMAGNETIC COMPATIBILITY - PRODUCT FAMILY STANDARD FOR AUDIO, VIDEO, AUDIO-VISUAL AND ENTERTAINMENT LIGHTING CONTROL APPARATUS FOR PROFESSIONAL USE - PART 2: IMMUNITY |
| I.S. EN 50512:2009 | ELECTRICAL INSTALLATIONS FOR LIGHTING AND BEACONING OF AERODROMES - ADVANCED VISUAL DOCKING GUIDANCE SYSTEMS (A-VDGS) |
| BS EN 61558-1 : 2005 | SAFETY OF POWER TRANSFORMERS, POWER SUPPLIES, REACTORS AND SIMILAR PRODUCTS - PART 1: GENERAL REQUIREMENTS AND TESTS |
| BS EN 61851-21:2002 | Electric vehicle conductive charging system Electric vehicle requirements for conductive connection to an a.c./d.c. supply |
| BS EN 12015:2014 | Electromagnetic compatibility. Product family standard for lifts, escalators and moving walks. Emission |
| UNE-EN 50083-2:2013 | Cable networks for television signals, sound signals and interactive services - Part 2: Electromagnetic compatibility for equipment |
| EN 12098-4 : 2005 | CONTROLS FOR HEATING SYSTEMS - PART 4: OPTIMUM START-STOP CONTROL EQUIPMENT FOR ELECTRICAL SYSTEMS |
| EN 61058-1:2002/A2:2008 | SWITCHES FOR APPLIANCES - PART 1: GENERAL REQUIREMENTS |
| EN 61000-4-13:2002/A2:2016 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-13: TESTING AND MEASUREMENT TECHNIQUES - HARMONICS AND INTERHARMONICS INCLUDING MAINS SIGNALLING AT A.C. POWER PORT, LOW FREQUENCY IMMUNITY TESTS (IEC 61000-4-13:2002/A2:2015) |
| EN 62282-3-1 : 2007 | FUEL CELL TECHNOLOGIES - PART 3-1: STATIONARY FUEL CELL POWER SYSTEMS - SAFETY |
| EN 62080:2009/A2:2015 | SOUND SIGNALLING DEVICES FOR HOUSEHOLD AND SIMILAR PURPOSES (IEC 62080:2001/A2:2015) |
| EN 61558-1:2005/A1:2009 | SAFETY OF POWER TRANSFORMERS, POWER SUPPLIES, REACTORS AND SIMILAR PRODUCTS - PART 1: GENERAL REQUIREMENTS AND TESTS |
| EN 12355:2003+A1:2010 | Food processing machinery - Derinding-, skinning- and membrane removal machines - Safety and hygiene requirements |
| EN 12182:2012 | Assistive products for persons with disability - General requirements and test methods |
| EN 50293:2012 | Road traffic signal systems - Electromagnetic compatibility |
| EN 60730-1:2016 | Automatic electrical controls - Part 1: General requirements |
| EN 61000-3-12:2011 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 3-12: LIMITS - LIMITS FOR HARMONIC CURRENTS PRODUCED BY EQUIPMENT CONNECTED TO PUBLIC LOW-VOLTAGE SYSTEMS WITH INPUT CURRENT > 16 A AND <= 75 A PER PHASE (IEC 61000-3-12:2011) |
| EN 60601-1-2:2015 | Medical electrical equipment - Part 1-2: General requirements for basic safety and essential performance - Collateral Standard: Electromagnetic disturbances - Requirements and tests |
| DIN EN 12015:1998-08 | ELECTROMAGNETIC COMPATIBILITY - PRODUCT FAMILY STANDARD FOR LIFTS, ESCALATORS AND MOVING WALKS - EMISSION |
| EN 60669-2-5:2016 | Switches for household and similar fixed electrical installations - Part 2-5: Particular requirements - Switches and related accessories for use in home and building electronic systems (HBES) |
| EN 62310-2:2007 | Static transfer systems (STS) - Part 2: Electromagnetic compatibility (EMC) requirements |
| EN 62606:2013/A1:2017 | GENERAL REQUIREMENTS FOR ARC FAULT DETECTION DEVICES (IEC 62606:2013/A1:2017) |
| EN 50564:2011 | Electrical and electronic household and office equipment - Measurement of low power consumption |
| EN 50083-2:2012/A1:2015 | CABLE NETWORKS FOR TELEVISION SIGNALS, SOUND SIGNALS AND INTERACTIVE SERVICES - PART 2: ELECTROMAGNETIC COMPATIBILITY FOR EQUIPMENT |
| EN 61000-6-3:2007/A1:2011/AC:2012 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-3: GENERIC STANDARDS - EMISSION STANDARD FOR RESIDENTIAL, COMMERCIAL AND LIGHT-INDUSTRIAL ENVIRONMENTS (IEC 61000-6-3:2006/A1:2010) |
| EN 300 132-1 : 2.0.1 DRAFT | ENVIRONMENTAL ENGINEERING (EE); POWER SUPPLY INTERFACE AT THE INPUT TO INFORMATION AND COMMUNICATION TECHNOLOGY (ICT) EQUIPMENT; PART 1: OPERATED BY ALTERNATING CURRENT (AC) SOURCE |
| CEI CWA 50487 : 2006 | SMARTHOUSE CODE OF PRACTICE |
| CEI EN 62282-3-201 : 2014 | FUEL CELL TECHNOLOGIES - PART 3-201: STATIONARY FUEL CELL POWER SYSTEMS - PERFORMANCE TEST METHODS FOR SMALL FUEL CELL POWER SYSTEMS |
| NF EN 301489-1 : 2012 | ELECTROMAGNETIC COMPATIBILITY AND RADIO SPECTRUM MATTERS (ERM) - ELECTROMAGNETIC COMPATIBILITY (EMC) STANDARD FOR RADIO EQUIPMENT AND SERVICES - PART 1: COMMON TECHNICAL REQUIREMENTS |
| 11/30255400 DC : 0 | BS EN 50293 - ELECTROMAGNETIC COMPATIBILITY - ROAD TRAFFIC SIGNAL SYSTEMS |
| BS EN 62282-5-1:2012 | Fuel cell technologies Portable fuel cell power systems. Safety |
| BS EN 50512:2009 | Electrical installations for lighting and beaconing of aerodromes. Advanced visual docking guidance systems (A-VDGS) |
| I.S. EN 62717:2017 | LED MODULES FOR GENERAL LIGHTING - PERFORMANCE REQUIREMENTS |
| BS EN 60974-10 : 2014 | ARC WELDING EQUIPMENT - PART 10: ELECTROMAGNETIC COMPATIBILITY (EMC) REQUIREMENTS |
| UNE-EN 60947-5-2:2008 | Low-voltage switchgear and controlgear - Part 5-2: Control circuit devices and switching elements - Proximity switches |
| EN 61851-21-1:2017/AC:2017-11 | ELECTRIC VEHICLE CONDUCTIVE CHARGING SYSTEM - PART 21-1: ELECTRIC VEHICLE ON-BOARD CHARGER EMC REQUIREMENTS FOR CONDUCTIVE CONNECTION TO AN AC/DC SUPPLY (IEC 61851-21-1:2017) |
| TS 102 192-1 : 1.1.1 | ELECTROMAGNETIC COMPATIBILITY AND RADIO SPECTRUM MATTERS (ERM); INTERNATIONAL TECHNICAL CHARACTERISTICS AND TEST METHODS; PART 1: WIRELESS/RADIO MICROPHONES IN THE 25 MHZ TO 3 GHZ FREQUENCY RANGE |
| 16/30340737 DC : 0 | BS EN 50121-4 - RAILWAY APPLICATIONS - ELECTROMAGNETIC COMPATIBILITY - PART 4: EMISSION AND IMMUNITY OF THE SIGNALLING AND TELECOMMUNICATIONS APPARATUS |
| BS EN 63002 : 2017 | IDENTIFICATION AND COMMUNICATION INTEROPERABILITY METHOD FOR EXTERNAL POWER SUPPLIES USED WITH PORTABLE COMPUTING DEVICES |
| EN 303 446-1 : 1.1.0 DRAFT | ELECTROMAGNETIC COMPATIBILITY (EMC) STANDARD FOR COMBINED AND/OR INTEGRATED RADIO AND NON-RADIO EQUIPMENT; PART 1: REQUIREMENTS FOR EQUIPMENT INTENDED TO BE USED IN RESIDENTIAL, COMMERCIAL AND LIGHT INDUSTRY LOCATIONS; HARMONISED STANDARD COVERING THE ESSENTIAL REQUIREMENTS OF ARTICLE 3.1(B) OF DIRECTIVE 2014/53/EU |
| DD CLC/TS 50217:2005 | Guide for in situ measurements. In situ measurement of disturbance emission |
| BS EN 61000-3-3:2013 | Electromagnetic compatibility (EMC) Limits. Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage supply systems, for equipment with rated current ≤ 16 A per phase and not subject to conditional connection |
| UNE-EN 50293:2013 | Road traffic signal systems - Electromagnetic compatibility |
| BS EN 62384 : 2006 | DC OR AC SUPPLIED ELECTRONIC CONTROL GEAR FOR LED MODULES - PERFORMANCE REQUIREMENTS |
| 03/102517 DC : 0 | BS EN 13633 - BUILDING HARDWARE - ELECTRICALLY CONTROLLED PANIC EXIT SYSTEMS - REQUIREMENTS AND TEST METHODS |
| PREN 50121-5 : DRAFT 2016 | RAILWAY APPLICATIONS - ELECTROMAGNETIC COMPATIBILITY - PART 5: EMISSION AND IMMUNITY OF FIXED POWER SUPPLY INSTALLATIONS AND APPARATUS |
| NF EN 61204-3 : 2001 | LOW VOLTAGE POWER SUPPLIES, D.C. OUTPUT - PART 3: ELECTROMAGNETIC COMPATIBILITY (EMC) |
| DIN EN 50107 : 1998 | SIGNS AND LUMINOUS-DISCHARGE-TUBE INSTALLATIONS OPERATING FROM A NO-LOAD OUTPUT VOLTAGE EXCEEDING 1 KV BUT NOT EXCEEDING 10 KV |
| ENV 50234 : DRAFT 1997 | AVIATION GROUND LIGHTING ELECTRICAL INSTALLATION - FLASHING LIGHTS: EQUIPMENT SPECIFICATIONS AND TESTS |
| I.S. EN 62282-3-1:2007 | FUEL CELL TECHNOLOGIES - PART 3-1: STATIONARY FUEL CELL POWER SYSTEMS - SAFETY |
| 04/30116612 DC : DRAFT JUL 2004 | EN 50121-4 - RAILWAY APPLICATIONS - ELECTROMAGNETIC COMPATIBILITY - PART 4: EMISSION AND IMMUNITY OF THE SIGNALLING AND TELECOMMUNICATIONS APPARATUS |
| 03/111744 DC : DRAFT JULY 2003 | |
| 99/240939 DC : DRAFT MAR 99 | BS EN 50330-1 PHOTOVOLTAIC SEMICONDUCTOR CONVERTORS - PART 1: UTILITY INTERACTIVE FAIL SAFE PROTECTIVE INTERFACE FOR PV-LINE COMMUTATED CONVERTORS - DESIGN QUALIFICATION AND TYPE APPROVAL |
| CEI EN 61851-22 : 2003 | ELECTRIC VEHICLE CONDUCTIVE CHARGING SYSTEM - PART 22: AC ELECTRIC VEHICLE CHARGING STATION |
| CEI EN 50438 : 2014 | REQUIREMENTS FOR MICRO-GENERATING PLANTS TO BE CONNECTED IN PARALLEL WITH PUBLIC LOW-VOLTAGE DISTRIBUTION NETWORKS |
| 95/214875 DC : 0 | PREN 50222 - STANDARD FOR THE EVALUATION OF MEASUREMENT RESULTS TAKING MEASUREMENT UNCERTAINTY INTO ACCOUNT |
| BS EN 60730-1 95 : 95 AMD 12021 | SPECIFICATION FOR AUTOMATIC ELECTRICAL CONTROLS FOR HOUSEHOLD AND SIMILAR USE - GENERAL REQUIREMENTS |
| I.S. EN 60669-2-5:2016 | SWITCHES FOR HOUSEHOLD AND SIMILAR FIXED ELECTRICAL INSTALLATIONS - PART 2-5: PARTICULAR REQUIREMENTS - SWITCHES AND RELATED ACCESSORIES FOR USE IN HOME AND BUILDING ELECTRONIC SYSTEMS (HBES) |
| I.S. EN 61000-3-3:2013 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 3-3: LIMITS - LIMITATION OF VOLTAGE CHANGES, VOLTAGE FLUCTUATIONS AND FLICKER IN PUBLIC LOW-VOLTAGE SUPPLY SYSTEMS, FOR EQUIPMENT WITH RATED CURRENT <= 16 A PER PHASE AND NOT SUBJECT TO CONDITIONAL CONNECTION (IEC 61000-3-3:2013 (EQV)) |
| BS EN 50465:2015 | European product standard for combined heating power systems using gas fuel |
| EN IEC 61058-1:2018 | Switches for appliances - Part 1: General requirements |
| I.S. EN 61000-4-13:2002 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-13: TESTING AND MEASUREMENT TECHNIQUES - HARMONICS AND INTERHARMONICS INCLUDING MAINS SIGNALLING AT A.C. POWER PORT, LOW FREQUENCY IMMUNITY TESTS |
| TR 102 121 : 1.2.1 | ENVIRONMENTAL ENGINEERING (EE); GUIDANCE FOR POWER DISTRIBUTION TO TELECOMMUNICATION AND DATACOM EQUIPMENT |
| CEI EN 62040-2 : 2006 | UNINTERRUPTIBLE POWER SYSTEMS (UPS) - PART 2: ELECTROMAGNETIC COMPATIBILITY (EMC) REQUIREMENTS |
| CEI EN 61786-1 : 2014 | MEASUREMENT OF DC MAGNETIC, AC MAGNETIC AND AC ELECTRIC FIELDS FROM 1 HZ TO 100 KHZ WITH REGARD TO EXPOSURE OF HUMAN BEINGS - PART 1: REQUIREMENTS FOR MEASURING INSTRUMENTS |
| PREN 50330-1 : DRAFT 99 | PHOTOVOLTAIC SEMICONDUCTOR CONVERTERS - PART 1: UTILITY INTERACTIVE FAIL SAFE PROTECTIVE INTERFACE FOR PV-LINE COMMUTATED CONVERTERS - DESIGN QUALIFICATION AND TYPE APPROVAL |
| I.S. EN 62310-2:2007 | STATIC TRANSFER SYSTEMS (STS) - PART 2: ELECTROMAGNETIC COMPATIBILITY (EMC) REQUIREMENTS |
| UNE-EN 61000-3-12:2012 | Electromagnetic compatibility (EMC) - Part 3-12: Limits - Limits for harmonic currents produced by equipment connected to public low-voltage systems with input current > 16 A and |
| I.S. EN 62080:2009 | SOUND SIGNALLING DEVICES FOR HOUSEHOLD AND SIMILAR PURPOSES |
| I.S. EN 60204-31:2013 | SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 31: PARTICULAR SAFETY AND EMC REQUIREMENTS FOR SEWING MACHINES, UNITS AND SYSTEMS (IEC 60204-31:2013 (EQV)) |
| BS EN 15194:2017 | Cycles. Electrically power assisted cycles. EPAC Bicycles |
| I.S. EN 61058-1:2002 | SWITCHES FOR APPLIANCES - PART 1: GENERAL REQUIREMENTS |
| BS EN 55103-1 : 2009 | ELECTROMAGNETIC COMPATIBILITY - PRODUCT FAMILY STANDARD FOR AUDIO, VIDEO, AUDIO-VISUAL AND ENTERTAINMENT LIGHTING CONTROL APPARATUS FOR PROFESSIONAL USE - PART 1: EMISSIONS |
| EN 60947-2:2017 | Low-voltage switchgear and controlgear - Part 2: Circuit-breakers |
| EN 62717:2017 | LED modules for general lighting - Performance requirements |
| BS EN 62040-3:2011 | Uninterruptible power systems (UPS) Method of specifying the performance and test requirements |
| I.S. EN 60947-5-2:2008 | LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 5-2: CONTROL CIRCUIT DEVICES AND SWITCHING ELEMENTS - PROXIMITY SWITCHES (IEC 60947-5-2:2007 (EQV)) |
| PREN 12182 : 2009-06 | ASSISTIVE PRODUCTS FOR PERSONS WITH DISABILITY - GENERAL REQUIREMENTS AND TEST METHODS |
| BS EN 50121-4:2016 | Railway applications. Electromagnetic compatibility Emission and immunity of the signalling and telecommunications apparatus |
| EN IEC 62909-1:2018 | Bi-directional grid-connected power converters - Part 1: General requirements |
| PREN 50465 : DRAFT 2011 | GAS APPLIANCES - COMBINED HEAT AND POWER APPLIANCE OF NOMINAL HEAT INPUT INFERIOR OR EQUAL TO 70 KW |
| UNE-EN 62080:2010 | Sound signalling devices for household and similar purposes |
| CEI EN 62920 : 1ED 2018 | PHOTOVOLTAIC POWER GENERATING SYSTEMS - EMC REQUIREMENTS AND TEST METHODS FOR POWER CONVERSION EQUIPMENT |
| PREN 12015 : DRAFT 2012 | ELECTROMAGNETIC COMPATIBILITY - PRODUCT FAMILY STANDARD FOR LIFTS, ESCALATORS ANS MOVING WALKS - EMISSION |
| EG 203 367 : 1.1.1 | GUIDE TO THE APPLICATION OF HARMONISED STANDARDS COVERING ARTICLES 3.1B AND 3.2 OF THE DIRECTIVE 2014/53/EU (RED) TO MULTI-RADIO AND COMBINED RADIO AND NON-RADIO EQUIPMENT |
| I.S. EN 50121-5:2017 | RAILWAY APPLICATIONS - ELECTROMAGNETIC COMPATIBILITY - PART 5: EMISSION AND IMMUNITY OF FIXED POWER SUPPLY INSTALLATIONS AND APPARATUS |
| I.S. EN 60146-1-1:2010 | SEMICONDUCTOR CONVERTERS - GENERAL REQUIREMENTS AND LINE COMMUTATED CONVERTERS - PART 1-1: SPECIFICATION OF BASIC REQUIREMENTS |
| EN 50465 : 2015 | GAS APPLIANCES - COMBINED HEAT AND POWER APPLIANCE OF NOMINAL HEAT INPUT INFERIOR OR EQUAL TO 70 KW |
| I.S. ETSI EN 301489-1 V1.8.1:2009 | ELECTROMAGNETIC COMPATIBILITY AND RADIO SPECTRUM MATTERS (ERM); ELECTROMAGNETIC COMPATIBILITY (EMC) STANDARD FOR RADIO EQUIPMENT AND SERVICES; PART 1: COMMON TECHNICAL REQUIREMENTS |
| I.S. EN 50465:2015 | GAS APPLIANCES - COMBINED HEAT AND POWER APPLIANCE OF NOMINAL HEAT INPUT INFERIOR OR EQUAL TO 70 KW |
| CEI EN 50121-4 : 2016 | RAILWAY APPLICATIONS - ELECTROMAGNETIC COMPATIBILITY - PART 4: EMISSION AND IMMUNITY OF THE SIGNALLING AND TELECOMMUNICATIONS APPARATUS |
| I.S. EN 62135-2:2015 | RESISTANCE WELDING EQUIPMENT - PART 2: ELECTROMAGNETIC COMPATIBILITY (EMC) REQUIREMENTS |
| I.S. EN 62040-3:2011 | UNINTERRUPTIBLE POWER SYSTEMS (UPS) - PART 3: METHOD OF SPECIFYING THE PERFORMANCE AND TEST REQUIREMENTS |
| S.R. CLC/TS 50509:2007 | USE OF LED SIGNAL HEADS IN ROAD TRAFFIC SIGNAL SYSTEMS |
| DIN EN 12182:2012-07 | Assistive products for persons with disability - General requirements and test methods |
| DIN EN 12015:2014-09 | Electromagnetic compatibility - Product family standard for lifts, escalators and moving walks - Emission; German version EN 12015:2014 |
| EN 62282-3-100:2012 | Fuel cell technologies - Part 3-100: Stationary fuel cell power systems - Safety |
| I.S. EN 12182:2012 | ASSISTIVE PRODUCTS FOR PERSONS WITH DISABILITY - GENERAL REQUIREMENTS AND TEST METHODS |
| DIN EN 12098-4:2005-12 | CONTROLS FOR HEATING SYSTEMS - PART 4: OPTIMUM START-STOP CONTROL EQUIPMENT FOR ELECTRICAL SYSTEMS |
| I.S. EN 12355:2003 | FOOD PROCESSING MACHINERY - DERINDING-, SKINNING- AND MEMBRANE REMOVAL MACHINES - SAFETY AND HYGIENE REQUIREMENTS |
| EN 60947-1:2007/A2:2014 | LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 1: GENERAL RULES (IEC 60947-1:2007/A2:2014) |
| I.S. EN 809:1998 | PUMPS AND PUMP UNITS FOR LIQUIDS - COMMON SAFETY REQUIREMENTS |
| DIN EN 1970:2005-10 | ADJUSTABLE BEDS FOR DISABLED PERSONS - REQUIREMENTS AND TEST METHODS |
| VDE 0128 : 1998 | SIGNS AND LUMINOUS-DISCHARGE-TUBE INSTALLATIONS OPERATING FROM A NO-LOAD RATED OUTPUT VOLTAGE EXCEEDING 1 KV BUT NOT EXCEEDING 10 KV |
| VDE V 0161-234 : 1998 | Aviation ground lighting electric installation - Flashing lights Equipment specifications and tests; |
| VDI 3551:2011-01 | Electromagnetic compatibility (EMC) in building services |
| DIN V ENV 50234 : 1998 | AERONAUTICAL GROUND LIGHTING ELECTRICAL INSTALLATION - FLASHING LIGHTS - EQUIPMENT SPECIFICATIONS AND TESTS |
| CEI EN 62040-3 : 2015 | UNINTERRUPTIBLE POWER SYSTEMS (UPS) - PART 3: METHOD OF SPECIFYING THE PERFORMANCE AND TEST REQUIREMENTS |
| 07/30164493 DC : 0 | BS EN 14637 - BUILDING HARDWARE - ELECTRICALLY CONTROLLED HOLD-OPEN SYSTEMS FOR FIRE/SMOKE DOOR ASSEMBLIES - REQUIREMENTS, TEST METHODS, APPLICATIONS AND MAINTENANCE |
| NF EN 300385 : 2001 | |
| BS EN 61851-21-1:2017 | Electric vehicle conductive charging system Electric vehicle on-board charger EMC requirements for conductive connection to an AC/DC supply |
| I.S. EN 50438:2013 | REQUIREMENTS FOR MICRO-GENERATING PLANTS TO BE CONNECTED IN PARALLEL WITH PUBLIC LOW-VOLTAGE DISTRIBUTION NETWORKS |
| CEI EN 50083-2 : 2012 | CABLE NETWORKS FOR TELEVISION SIGNALS, SOUND SIGNALS AND INTERACTIVE SERVICES - PART 2: ELECTROMAGNETIC COMPATIBILITY FOR EQUIPMENT |
| BS EN 50366 : 2003 | HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - ELECTROMAGNETIC FIELDS - METHODS FOR EVALUATION AND MEASUREMENT |
| 12/30258326 DC : 0 | BS EN 12015 - ELECTROMAGNETIC COMPATIBILITY - PRODUCT FAMILY STANDARD FOR LIFTS, ESCALATORS ANS MOVING WALKS - EMISSION |
| 09/30192320 DC : DRAFT MAY 2009 | BS EN 13633 - BUILDING HARDWARE - ELECTRICALLY CONTROLLED PANIC EXIT SYSTEMS FOR USE ON ESCAPE ROUTES - REQUIREMENTS AND TEST METHODS |
| UNE-EN 50512:2011 | Electrical installations for lighting and beaconing of aerodromes - Advanced Visual Docking Guidance Systems (A-VDGS) |
| 16/30340740 DC : 0 | BS EN 50121-5 - RAILWAY APPLICATIONS - ELECTROMAGNETIC COMPATIBILITY - PART 5: EMISSION AND IMMUNITY OF FIXED POWER SUPPLY INSTALLATIONS AND APPARATUS |
| 08/30181001 DC : DRAFT APR 2008 | BS EN 50512 - ELECTRICAL INSTALLATIONS FOR LIGHTING AND BEACONING OF AERODROMES - ADVANCED VISUAL DOCKING GUIDANCE SYSTEMS (A-VDGS) |
| EN 61851-21:2002 | Electric vehicle conductive charging system - Part 21: Electric vehicle requirements for conductive connection to an a.c/d.c. supply |
| BS EN 61851-22:2002 | Electric vehicle conductive charging system A.C. electric vehicle charging station |
| BS EN 61000-4-7 : 2002 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-7: TESTING AND MEASUREMENT TECHNIQUES - GENERAL GUIDE ON HARMONICS AND INTERHARMONICS MEASUREMENTS AND INSTRUMENTATION, FOR POWER SUPPLY SYSTEMS AND EQUIPMENT CONNECTED THERETO |
| CEI EN 60947-5-9 : 2008 | LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 5-9: CONTROL CIRCUIT DEVICES AND SWITCHING ELEMENTS - FLOW RATE SWITCHES |
| 09/30201992 DC : 0 | BS EN 12182 - ASSISTIVE PRODUCTS FOR PERSONS WITH DISABILITY - GENERAL REQUIREMENTS AND TEST METHODS |
| TS 102 874-6 : 1.1.1 | ACCESS, TERMINALS, TRANSMISSION AND MULTIPLEXING (ATTM); EXTERNAL COMMON POWER SUPPLY FOR CUSTOMER PREMISES NETWORK AND ACCESS EQUIPMENT; PART 6: CPS TYPE 2.D IMPLEMENTATION DETAILS |
| BS EN 62811:2015 | AC and/or DC-supplied electronic controlgear for discharge lamps (excluding fluorescent lamps). Performance requirements for low frequency squarewave operation |
| BS EN 50438:2013 | Requirements for micro-generating plants to be connected in parallel with public low-voltage distribution networks |
| UNE-EN 13637:2016 | Building hardware - Electrically controlled exit systems for use on escape routes - Requirements and test methods |
| UNE-EN 55103-2:2010 | Electromagnetic compatibility - Product family standard for audio, video, audio-visual and entertainment lighting control apparatus for professional use - Part 2: Immunity |
| CEI EN 62282-3-100 : 2012 | FUEL CELL TECHNOLOGIES - PART 3-100: STATIONARY FUEL CELL POWER SYSTEMS - SAFETY |
| BS EN 50199:1996 | Electromagnetic compatibility (EMC). Product standard for arc welding equipment |
| BS EN 62282-3-201:2017 | Fuel cell technologies Stationary fuel cell power systems. Performance test methods for small fuel cell power systems |
| BS EN 61000-4-1:2007 | Electromagnetic compatibility (EMC) Testing and measurement techniques. Overview of IEC 61000-4 series |
| UNE-EN 61786-1:2014 | Measurement of DC magnetic, AC magnetic and AC electric fields from 1 Hz to 100 kHz with regard to exposure of human beings - Part 1: Requirements for measuring instruments |
| PREN 50293 : DRAFT 2011 | ELECTROMAGNETIC COMPATIBILITY - ROAD TRAFFIC SIGNAL SYSTEMS |
| EN 62040-3:2011 | Uninterruptible power systems (UPS) - Part 3: Method of specifying the performance and test requirements |
| DIN 57128 : 1981 | |
| CLC/TS 50509:2007 | Use of LED signal heads in road traffic signal systems |
| EN 50121-5:2017 | Railway applications - Electromagnetic compatibility - Part 5: Emission and immunity of fixed power supply installations and apparatus |
| BS EN 61800-3 : 2004 | ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 3: EMC REQUIREMENTS AND SPECIFIC TEST METHODS |
| CEI EN 61326-1 : 2013 | ELECTRICAL EQUIPMENT FOR MEASUREMENT, CONTROL AND LABORATORY USE - EMC REQUIREMENTS - PART 1: GENERAL REQUIREMENTS |
| I.S. CLC/TS 50217:2005 | GUIDE FOR IN SITU MEASUREMENTS - IN SITU MEASUREMENT OF DISTURBANCE EMISSION |
| BS EN 61058-1 : 2002 | SWITCHES FOR APPLIANCES - PART 1: GENERAL REQUIREMENTS |
| I.S. EN 50065-2-1:2003 | SIGNALLING ON LOW-VOLTAGE ELECTRICAL INSTALLATIONS IN THE FREQUENCY RANGE 3 KHZ TO 148,5 KHZ - PART 2-1: IMMUNITY REQUIREMENTS FOR MAINS COMMUNICATIONS EQUIPMENT AND SYSTEMS OPERATING IN THE RANGE OF FREQUENCIES 95 KHZ TO 148,5 KHZ AND INTENDED FOR USE IN RESIDENTIAL, COMMERCIAL AND LIGHT INDUSTRIAL ENVIRONMENTS |
| TR 102 446 : 1.1.1 | ENVIRONMENTAL ENGINEERING (EE); GENERAL REQUIREMENTS FOR UPS FOR USE IN TELECOMMUNICATION ENVIRONMENT |
| I.S. EN IEC 62909-1:2018 | BI-DIRECTIONAL GRID-CONNECTED POWER CONVERTERS - PART 1: GENERAL REQUIREMENTS |
| I.S. EN 61326:1998 | |
| EN 50121-4:2016 | Railway applications - Electromagnetic compatibility - Part 4: Emission and immunity of the signalling and telecommunications apparatus |
| I.S. EN 61786-1:2014 | MEASUREMENT OF DC MAGNETIC, AC MAGNETIC AND AC ELECTRIC FIELDS FROM 1 HZ TO 100 KHZ WITH REGARD TO EXPOSURE OF HUMAN BEINGS - PART 1: REQUIREMENTS FOR MEASURING INSTRUMENTS |
| I.S. EN 61851-21-1:2017 | ELECTRIC VEHICLE CONDUCTIVE CHARGING SYSTEM - PART 21-1: ELECTRIC VEHICLE ON-BOARD CHARGER EMC REQUIREMENTS FOR CONDUCTIVE CONNECTION TO AN AC/DC SUPPLY |
| PREN 12184 : DRAFT 2011 | ELECTRICALLY POWERED WHEELCHAIRS, SCOOTERS AND THEIR CHARGERS - REQUIREMENTS AND TEST METHODS |
| UNE-EN 60669-2-5:2017 | Switches for household and similar fixed electrical installations - Part 2-5: Particular requirements - Switches and related accessories for use in home and building electronic systems (HBES) |
| VDE 0557-3 : 2001 COR 1 2004 | LOW-VOLTAGE POWER SUPPLIES, D.C. OUTPUT - PART 3: PRODUCT EMC STANDARD |
| I.S. EN 63002:2017 | IDENTIFICATION AND COMMUNICATION INTEROPERABILITY METHOD FOR EXTERNAL POWER SUPPLIES USED WITH PORTABLE COMPUTING DEVICES |
| CLC/TR 50627:2015 | Study Report on Electromagnetic Interference between Electrical Equipment/Systems in the Frequency Range Below 150 kHz |
| S.R. CLC/TR 50627:2015 | STUDY REPORT ON ELECTROMAGNETIC INTERFERENCE BETWEEN ELECTRICAL EQUIPMENT/SYSTEMS IN THE FREQUENCY RANGE BELOW 150 KHZ |
| EN 300 386-2 : 1.1.3 | ELECTROMAGNETIC COMPATIBILITY AND RADIO SPECTRUM MATTERS (ERM); TELECOMMUNICATION NETWORK EQUIPMENT; ELECTROMAGNETIC COMPATIBILITY (EMC) REQUIREMENTS; PRODUCT FAMILY STANDARD |
| TR 102 937 : 1.1.1 | ECALL COMMUNICATIONS EQUIPMENT; CONFORMANCE TO EU VEHICLE REGULATIONS, R&TTE, EMC & LV DIRECTIVES, AND EU REGULATIONS FOR ECALL IMPLEMENTATION |
| I.S. EN 60601-1-2:2015 | MEDICAL ELECTRICAL EQUIPMENT - PART 1-2: GENERAL REQUIREMENTS FOR BASIC SAFETY AND ESSENTIAL PERFORMANCE - COLLATERAL STANDARD: ELECTROMAGNETIC DISTURBANCES - REQUIREMENTS AND TESTS |
| I.S. EN 50121-4:2016 | RAILWAY APPLICATIONS - ELECTROMAGNETIC COMPATIBILITY - PART 4: EMISSION AND IMMUNITY OF THE SIGNALLING AND TELECOMMUNICATIONS APPARATUS |
| I.S. EN 15194:2017 | CYCLES - ELECTRICALLY POWER ASSISTED CYCLES - EPAC BICYCLES |
| I.S. EN 62041:2010 | SAFETY OF TRANSFORMERS, REACTORS, POWER SUPPLY UNITS AND COMBINATIONS THEREOF - EMC REQUIREMENTS |
| I.S. EN 60947-2:2017 | LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 2: CIRCUIT-BREAKERS |
| DIN EN 12355:2011-02 | Food processing machinery - Derinding-, skinning- and membrane removal machines - Safety and hygiene requirements (includes Amendment A1:2010) |
| DIN EN 14637 E : 2008 | BUILDING HARDWARE - ELECTRICALLY CONTROLLED HOLD-OPEN SYSTEMS FOR FIRE/SMOKE DOOR ASSEMBLIES - REQUIREMENTS, TEST METHODS, APPLICATION AND MAINTENANCE |
| BS EN 12355 : 2003 | FOOD PROCESSING MACHINERY - DERINDING-, SKINNING- AND MEMBRANE REMOVAL MACHINES - SAFETY AND HYGIENE REQUIREMENTS |
| BS EN 12098-4:2005 | Controls for heating systems Optimum start-stop control equipment for electrical systems |
| BS EN 14637:2007 | Building hardware. Electrically controlled hold-open systems for fire/smoke door assemblies. Requirements, test methods, application and maintenance |
| BS EN 809 : 1998 | PUMPS AND PUMP UNITS FOR LIQUIDS - COMMON SAFETY REQUIREMENTS |
| EN 60745-1:2009/A11:2010 | HAND-HELD MOTOR-OPERATED ELECTRIC TOOLS - SAFETY - PART 1: GENERAL REQUIREMENTS |
| UNI EN 12015 : 2014 | ELECTROMAGNETIC COMPATIBILITY - PRODUCT FAMILY STANDARD FOR LIFTS, ESCALATORS AND MOVING WALKS - EMISSION |
| EN 62384:2006/A1:2009 | DC OR AC SUPPLIED ELECTRONIC CONTROL GEAR FOR LED MODULES - PERFORMANCE REQUIREMENTS |
| EN 60745-1:2006 | HAND-HELD MOTOR-OPERATED ELECTRIC TOOLS - SAFETY - PART 1: GENERAL REQUIREMENTS |
| EN 12015:2014 | Electromagnetic compatibility - Product family standard for lifts, escalators and moving walks - Emission |
| EN 809 : 1998 COR 2010 | PUMPS AND PUMP UNITS FOR LIQUIDS - COMMON SAFETY REQUIREMENTS |
| EN 809:1998+A1:2009 | Pumps and pump units for liquids - Common safety requirements |
| UNE-EN 60730-1:2013 | Automatic electrical controls for household and similar use - Part 1: General requirements |
| EN 300 386 : 1.6.1 | TELECOMMUNICATION NETWORK EQUIPMENT; ELECTROMAGNETIC COMPATIBILITY (EMC) REQUIREMENTS; HARMONISED STANDARD COVERING THE ESSENTIAL REQUIREMENTS OF THE DIRECTIVE 2014/30/EU |
| I.S. EN 12015:2014 | ELECTROMAGNETIC COMPATIBILITY - PRODUCT FAMILY STANDARD FOR LIFTS, ESCALATORS AND MOVING WALKS - EMISSION |
| EN 1970:2000/A1:2005 | ADJUSTABLE BEDS FOR DISABLED PERSONS - REQUIREMENTS AND TEST METHODS |
| UNI EN 809 : 2009 | PUMPS AND PUMP UNITS FOR LIQUIDS - COMMON SAFETY REQUIREMENTS |
| EN 50199 : 95 AC 98 | |
| EN 50465:2015 | Gas appliances - Combined heat and power appliance of nominal heat input inferior or equal to 70 kW |
| EN 50366 : 2003 AMD 1 2006 | HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - ELECTROMAGNETIC FIELDS - METHODS FOR EVALUATION AND MEASUREMENT |
| UNI EN 12182 : 2012 | ASSISTIVE PRODUCTS FOR PERSONS WITH DISABILITY - GENERAL REQUIREMENTS AND TEST METHODS |
| UNI EN 12355 : 2010 | FOOD PROCESSING MACHINERY - DERINDING-, SKINNING- AND MEMBRANE REMOVAL MACHINES - SAFETY AND HYGIENE REQUIREMENTS |
| UNE-EN 61000-4-7:2004 | Electromagnetic compatibility (EMC) -- Part 4-7: Testing and measurement techniques - General guide on harmonics and interharmonics measurements and instrumentation, for power supply systems and equipment connected thereto |
| DD ENV 50234:1997 | Aeronautical ground lighting electrical installation. Flashing lights. Equipment specifications and tests |
| BS EN 60669-2-5:2016 | Switches for household and similar fixed electrical installations Particular requirements. Switches and related accessories for use in home and building electronic systems (HBES) |
| UNE-EN 62282-3-1:2011 | Fuel cell technologies - Part 3-1: Stationary fuel cell power systems - Safety |
| PREN 50121-4 : DRAFT 2016 | RAILWAY APPLICATIONS - ELECTROMAGNETIC COMPATIBILITY - PART 4: EMISSION AND IMMUNITY OF THE SIGNALLING AND TELECOMMUNICATIONS APPARATUS |
| BS EN 60947-1 : 2007 | LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 1: GENERAL RULES |
| BS EN 55103-2:2009 | Electromagnetic compatibility. Product family standard for audio, video, audio-visual and entertainment lighting control apparatus for professional use Immunity |
| DIN V ENV 50091-3 : 2000 | UNINTERRUPTIBLE POWER SYSTEMS (UPS) - PART 3: PERFORMANCE REQUIREMENTS |
| I.S. EN 61204-3:2000 | LOW VOLTAGE POWER SUPPLIES, D.C. OUTPUT - PART 3: ELECTROMAGNETIC COMPATIBILITY (EMC) |
| CEI EN 62041 : 2012 | SAFETY OF TRANSFORMERS, REACTORS, POWER SUPPLY UNITS AND COMBINATIONS THEREOF - EMC REQUIREMENTS |
| PD CLC/TR 50627:2015 | Study Report on Electromagnetic Interference between Electrical Equipment/Systems in the Frequency Range Below 150 kHz |
| 16/30336682 DC : 0 | BS EN 62717 ED1.0 - LED MODULES FOR GENERAL LIGHTING - PERFORMANCE REQUIREMENTS |
| BS EN 61326-1:2013 | Electrical equipment for measurement, control and laboratory use. EMC requirements General requirements |
| BS EN 62310-2:2007 | Static transfer systems (STS) Electromagnetic compatibility (EMC) requirements |
| CEI EN 61000-4-1 : 2016 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-1: TESTING AND MEASUREMENT TECHNIQUES - OVERVIEW OF IEC 61000-4 SERIES |
| BS EN 50083-2 : 2012 | CABLE NETWORKS FOR TELEVISION SIGNALS, SOUND SIGNALS AND INTERACTIVE SERVICES - PART 2: ELECTROMAGNETIC COMPATIBILITY FOR EQUIPMENT |
| BS EN 60601-1-2:2015 | Medical electrical equipment General requirements for basic safety and essential performance. Collateral Standard. Electromagnetic disturbances. Requirements and tests |
| 02/204840 DC : DRAFT APR 2002 | PREN 50217 - IN SITU MEASUREMENTS OF DISTURBANCE EMISSION |
| BS EN 62041:2010 | Safety of transformers, reactors, power supply units and combinations thereof. EMC requirements |
| 04/30117565 DC : DRAFT AUG 2004 | EN 50438 - REQUIREMENTS FOR THE CONNECTION OF MICRO-COGENERATORS IN PARALLEL WITH PUBLIC LOW-VOLTAGE DISTRIBUTION NETWORKS |
| DD CLC/TS 50509:2007 | Use of LED signal heads in road traffic signal systems |
| 11/30237926 DC : 0 | BS EN 12184 - ELECTRICALLY POWERED WHEELCHAIRS, SCOOTERS AND THEIR CHARGERS - REQUIREMENTS AND TEST METHODS |
| BS EN 50121-5:2017 | Railway applications. Electromagnetic compatibility Emission and immunity of fixed power supply installations and apparatus |
| BS EN 61326:1998 | Electrical equipment for measurement, control and laboratory use. EMC requirements |
| CEI EN 62717 : 2017 | LED MODULES FOR GENERAL LIGHTING - PERFORMANCE REQUIREMENTS |
| I.S. EN 62612:2013 | SELF-BALLASTED LED LAMPS FOR GENERAL LIGHTING SERVICES WITH SUPPLY VOLTAGES > 50 V - PERFORMANCE REQUIREMENTS |
| I.S. EN 62282-5-1:2012 | FUEL CELL TECHNOLOGIES - PART 5-1: PORTABLE FUEL CELL POWER SYSTEMS - SAFETY (IEC 62282-5-1:2012 (EQV)) |
| I.S. EN 62282-3-100:2012 | FUEL CELL TECHNOLOGIES - PART 3-100: STATIONARY FUEL CELL POWER SYSTEMS - SAFETY (IEC 62282-3-100:2012 (EQV)) |
| I.S. EN 60669-2-1:2004 | SWITCHES FOR HOUSEHOLD AND SIMILAR FIXED ELECTRICAL INSTALLATIONS - PART 2-1: PARTICULAR REQUIREMENTS - ELECTRONIC SWITCHES |
| CEI EN 60146-1-1 : 2013 | SEMICONDUCTOR CONVERTERS - GENERAL REQUIREMENTS AND LINE COMMUTATED CONVERTERS - PART 1-1: SPECIFICATION OF BASIC REQUIREMENTS |
| CEI EN 62310-2 : 2007 | STATIC TRANSFER SYSTEMS (STS) - PART 3: METHOD OF SPECIFYING THE PERFORMANCE AND TEST REQUIREMENTS |
| CEI 214-3/1 : 1999 | TAXI FLEET MANAGEMENT - GENERAL REFERENCE |
| I.S. EN 61000-4-1:2007 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-1: TESTING AND MEASUREMENT TECHNIQUES - OVERVIEW OF IEC 61000-4 SERIES |
| I.S. EN 60730-1:2016 | AUTOMATIC ELECTRICAL CONTROLS - PART 1: GENERAL REQUIREMENTS |
| I.S. EN 60745-1:2009 | HAND-HELD MOTOR-OPERATED ELECTRIC TOOLS - SAFETY - PART 1: GENERAL REQUIREMENTS |
| I.S. CWA 14642:2003 | CEN WORKSHOP AGREEMENT (CWA) - ELECTRICAL INTERFACE FOR DOMESTIC COGENERATION - REQUIREMENTS FOR DISTRIBUTION NETWORK CONNECTION FOR MICRO COGENERATION SYSTEMS FOR DOMESTIC USE UP TO 16 A PER PHASE IN LOW-VOLTAGE DISTRIBUTION NETWORKS |
| I.S. EN 50083-2:2012 | CABLE NETWORKS FOR TELEVISION SIGNALS, SOUND SIGNALS AND INTERACTIVE SERVICES - PART 2: ELECTROMAGNETIC COMPATIBILITY FOR EQUIPMENT |
| I.S. EN 62040-2:2006 | UNINTERRUPTIBLE POWER SYSTEMS (UPS) - PART 2: ELECTROMAGNETIC COMPATIBILITY (EMC) REQUIREMENTS |
| I.S. EN 60439-1:2000 | LOW VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES - PART 1 - TYPE TESTED AND PARTIALLY TYPE TESTED ASSEMBLIES |
| DIN EN 809:2012-10 | Pumps and pump units for liquids - Common safety requirements |
| BS EN 60947-2:2017+A1:2020 | Low-voltage switchgear and controlgear Circuit-breakers |
| BS EN 60204-31:2013 | Safety of machinery. Electrical equipment of machines Particular safety and EMC requirements for sewing machines, units and systems |
| UNE-EN 62612:2014 | Self-ballasted LED lamps for general lighting services with supply voltages > 50 V - Performance requirements |
| EN 60947-5-2:2007/A1:2012 | LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 5-2: CONTROL CIRCUIT DEVICES AND SWITCHING ELEMENTS - PROXIMITY SWITCHES (IEC 60947-5-2:2007/A1:2012) |
| UNE-EN 50065-2-3:2004 | Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148,5 kHz -- Part 2-3: Immunity requirements for mains communications equipment and systems operating in the range of frequencies 3 kHz to 95 kHz and intended for use by electricity suppliers and distributors |
| BS EN 1970:2000 | Adjustable beds for disabled persons. Requirements and test methods |
| BS EN 60439-1:1999 | Low-voltage switchgear and controlgear assemblies Type-tested and partially type-tested assemblies |
| BS EN 60669-2-1 : 2004 | SWITCHES FOR HOUSEHOLD AND SIMILAR FIXED ELECTRICAL INSTALLATIONS - PART 2-1: PARTICULAR REQUIREMENTS - ELECTRONIC SWITCHES |
| UNE-EN 60204-31:2013 | Safety of machinery - Electrical equipment of machines - Part 31: Particular safety and EMC requirements for sewing machines, units and systems |
| BS EN 12182:2012 | Assistive products for persons with disability. General requirements and test methods |
| EN 61204-3:2000 | Low voltage power supplies, d.c. output - Part 3: Electromagnetic compatibility (EMC) |
| EN 13637:2015 | Building hardware - Electrically controlled exit systems for use on escape routes - Requirements and test methods |
| EN 14637:2007 | Building hardware - Electrically controlled hold-open systems for fire/smoke door assemblies - Requirements, test methods, application and maintenance |
| EN 15194:2017 | Cycles - Electrically power assisted cycles - EPAC Bicycles |
| UNE-EN 50564:2012 | Electrical and electronic household and office equipment - Measurement of low power consumption |
| 04/30116608 DC : DRAFT JUL 2004 | EN 50121-5 - RAILWAY APPLICATIONS - ELECTROMAGNETIC COMPATIBILITY - PART 5: EMISSION AND IMMUNITY OF FIXED POWER SUPPLY INSTALLATIONS AND APPARATUS |
| UNE-EN 61000-3-3:2013 | Electromagnetic compatibility (EMC) - Part 3-3: Limits - Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage supply systems, for equipment with rated current |
| 03/102518 DC : 0 | BS EN 13637 - BUILDING HARDWARE - ELECTRICALLY CONTROLLED EMERGENCY EXIT SYSTEMS FOR USE ON ESCAPE ROUTES - REQUIREMENTS AND TEST METHODS |
| TS 102 121 : 1.3.1 | ENVIRONMENTAL ENGINEERING (EE); POWER DISTRIBUTION TO TELECOMMUNICATIONS AND DATACOM (ICT) EQUIPMENT |
| I.S. EN 62606:2013 | GENERAL REQUIREMENTS FOR ARC FAULT DETECTION DEVICES |
| EN 61851-22:2002 | Electric vehicle conductive charging system - Part 22: AC electric vehicle charging station |
| 15/30321305 DC : 0 | BS EN 15194 - CYCLES - ELECTRICALLY POWER ASSISTED CYCLES - EPAC BICYCLES |
| 13/30252777 DC : 0 | BS EN 50121-4 - RAILWAY APPLICATIONS - ELECTROMAGNETIC COMPATIBILITY - PART 4: EMISSION AND IMMUNITY OF THE SIGNALLING AND TELECOMMUNICATIONS APPARATUS |
| BS EN 50065-2-1:2003 | Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148,5 kHz Immunity requirements for mains communications equipment and systems operating in the range of frequencies 95 kHz to 148,5 kHz and intended for use in residential, commercial and light industrial environments |
| BS EN 50564:2011 | Electrical and electronic household and office equipment. Measurement of low power consumption |
| 11/30249911 DC : 0 | BS EN 50465 - GAS APPLIANCES - COMBINED HEAT AND POWER APPLIANCE OF NOMINAL HEAT INPUT INFERIOR OR EQUAL TO 70 KW |
| 16/30337838 DC | BS EN 62612 AMD1. Self-ballasted LED lamps for general lighting services with supply voltages > 50 V. Performance requirements |
| I.S. EN 61000-6-3:2007 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-3: GENERIC STANDARDS - EMISSION STANDARD FOR RESIDENTIAL, COMMERCIAL AND LIGHT-INDUSTRIAL ENVIRONMENTS (IEC 61000-6-3:2006 (EQV)) |
| 09/30200143 DC : 0 | BS EN 62080 - SOUND SIGNALLING DEVICES FOR HOUSEHOLD AND SIMILAR PURPOSES |
| BS EN 50491-5-1:2010 | General requirements for home and building electronic systems (HBES) and building automation and control systems (BACS) EMC requirements, conditions and test set-up |
| I.S. EN 50065-2-3:2003 | SIGNALLING ON LOW-VOLTAGE ELECTRICAL INSTALLATIONS IN THE FREQUENCY RANGE 3 KHZ TO 148,5 KHZ - PART 2-3: IMMUNITY REQUIREMENTS FOR MAINS COMMUNICATIONS EQUIPMENT AND SYSTEMS OPERATING IN THE RANGE OF FREQUENCIES 3 KHZ TO 95 KHZ AND INTENDED FOR USE BY ELECTRICITY SUPPLIERS AND DISTRIBUTORS |
| BS EN 60947-5-9:2007 | Low-voltage switchgear and controlgear Control circuit devices and switching elements. Flow rate switches |
| BS EN 62135-2:2015 | Resistance welding equipment Electromagnetic compatibility (EMC) requirements |
| BS EN 62612:2013+A2:2018 | Self-ballasted LED lamps for general lighting services with supply voltages > 50 V. Performance requirements |
| BS EN 61000-3-12:2011 | Electromagnetic compatibility (EMC) Limits. Limits for harmonic currents produced by equipment connected to public low-voltage systems with input current > 16 A and ≤ 75 A per phase |
| CEI CLC/TS 50509 : 2008 | USE OF LED SIGNAL HEADS IN ROAD TRAFFIC SIGNAL SYSTEMS |
| NF EN 50491-5-1 : 2011 | GENERAL REQUIREMENTS FOR HOME AND BUILDING ELECTRONIC SYSTEMS (HBES) AND BUILDING AUTOMATION AND CONTROL SYSTEMS (BACS) - PART 5-1: EMC REQUIREMENTS, CONDITIONS AND TEST SET-UP |
| BS EN 60146-1-1:2010 | Semiconductor converters. General requirements and line commutated converters Specification of basic requirements |
| BS EN 62040-2:2006 | Uninterruptible power systems (UPS) Electromagnetic compatibility (EMC) requirements |
| DIN EN 13637:2015-12 | BUILDING HARDWARE - ELECTRICALLY CONTROLLED EXIT SYSTEMS FOR USE ON ESCAPE ROUTES - REQUIREMENTS AND TEST METHODS |
| I.S. EN 13637:2015 | BUILDING HARDWARE - ELECTRICALLY CONTROLLED EXIT SYSTEMS FOR USE ON ESCAPE ROUTES - REQUIREMENTS AND TEST METHODS |
| I.S. EN 61000-3-12:2011 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 3-12: LIMITS - LIMITS FOR HARMONIC CURRENTS PRODUCED BY EQUIPMENT CONNECTED TO PUBLIC LOW-VOLTAGE SYSTEMS WITH INPUT CURRENT > 16 A AND <= 75 A PER PHASE (IEC 61000-3-12:2011 (EQV)) |
| STANAG 7158 : 2009 | ELECTROMAGNETIC INTERFERENCE, TEST METHODS FOR AEROSPACE GROUND EQUIPMENT |
| I.S. EN 62282-3-201:2017 | FUEL CELL TECHNOLOGIES - PART 3-201: STATIONARY FUEL CELL POWER SYSTEMS - PERFORMANCE TEST METHODS FOR SMALL FUEL CELL POWER SYSTEMS |
| BS EN 60745-1 : 2009 | HAND-HELD MOTOR-OPERATED ELECTRIC TOOLS - SAFETY - PART 1: GENERAL REQUIREMENTS |
| CEI EN 50491-5-1 : 2011 | GENERAL REQUIREMENTS FOR HOME AND BUILDING ELECTRONIC SYSTEMS (HBES) AND BUILDING AUTOMATION AND CONTROL SYSTEMS (BACS) - PART 5-1: EMC REQUIREMENTS, CONDITIONS AND TEST SET-UP |
| TR 102 070-1 : 1.2.1 | ELECTROMAGNETIC COMPATIBILITY AND RADIO SPECTRUM MATTERS (ERM); GUIDE TO THE APPLICATION OF HARMONIZED STANDARDS TO MULTI-RADIO AND COMBINED RADIO AND NON-RADIO EQUIPMENT; PART 1: ELECTROMAGNETIC COMPATIBILITY |
| I.S. EN 60947-1:2007 | LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 1: GENERAL RULES |
| I.S. EN 55103-2:2009 | ELECTROMAGNETIC COMPATIBILITY - PRODUCT FAMILY STANDARD FOR AUDIO, VIDEO, AUDIO-VISUAL AND ENTERTAINMENT LIGHTING CONTROL APPARATUS FOR PROFESSIONAL USE - PART 2: IMMUNITY |
| BS EN 60947-2:2017 | Low-voltage switchgear and controlgear Circuit-breakers |
| CEI EN 50564 : 2013 | ELECTRICAL AND ELECTRONIC HOUSEHOLD AND OFFICE EQUIPMENT - MEASUREMENT OF LOW POWER CONSUMPTION |
| I.S. EN 60947-5-1:2017 | LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 5-1: CONTROL CIRCUIT DEVICES AND SWITCHING ELEMENTS - ELECTROMECHANICAL CONTROL CIRCUIT DEVICES |
| I.S. EN 62920:2017 | PHOTOVOLTAIC POWER GENERATING SYSTEMS - EMC REQUIREMENTS AND TEST METHODS FOR POWER CONVERSION EQUIPMENT |
| I.S. EN 61000-4-7:2002 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-7: TESTING AND MEASUREMENT TECHNIQUES - GENERAL GUIDE ON HARMONICS AND INTERHARMONICS MEASUREMENTS AND INSTRUMENTATION, FOR POWER SUPPLY SYSTEMS AND EQUIPMENT CONNECTED THERETO |
| BS EN 61000-4-13 : 2002 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-13: TESTING AND MEASUREMENT TECHNIQUES - HARMONICS AND INTERHARMONICS INCLUDING MAINS SIGNALLING AT A.C. POWER PORT, LOW FREQUENCY IMMUNITY TESTS (IEC 61000-4-13:2002) |
| UNE-EN 62041:2011 | Safety of transformers, reactors, power supply units and combinations thereof - EMC requirements |
| I.S. EN 50366:2003 | HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - ELECTROMAGNETIC FIELDS - METHODS FOR EVALUATION AND MEASUREMENT |
| UNE-EN 50121-4:2017 | Railway applications - Electromagnetic compatibility - Part 4: Emission and immunity of the signalling and telecommunications apparatus |
| EN 62920:2017 | Photovoltaic power generating systems - EMC requirements and test methods for power conversion equipment |
| CEI EN 55103-2 : 2010 | ELECTROMAGNETIC COMPATIBILITY - PRODUCT FAMILY STANDARD FOR AUDIO, VIDEO, AUDIOVISUAL AND ENTERTAINMENT LIGHTING CONTROL APPARATUS FOR PROFESSIONAL USE - PART 2: IMMUNITY |
| I.S. EN 50293:2012 | ROAD TRAFFIC SIGNAL SYSTEMS - ELECTROMAGNETIC COMPATIBILITY |
| BS EN 809:1998+A1:2009 | Pumps and pump units for liquids. Common safety requirements |
| I.S. EN 50240:2006 | |
| I.S. EN 50491-5-1:2010 | GENERAL REQUIREMENTS FOR HOME AND BUILDING ELECTRONIC SYSTEMS (HBES) AND BUILDING AUTOMATION AND CONTROL SYSTEMS (BACS) - PART 5-1: EMC REQUIREMENTS, CONDITIONS AND TEST SET-UP |
| EN 61800-3 : 2004 AMD 1 2012 | ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 3: EMC REQUIREMENTS AND SPECIFIC TEST METHODS (IEC 61800-3:2004/A1:2011) |
| UNE-EN 61439-1:2012 | Low-voltage switchgear and controlgear assemblies - Part 1: General rules |
| IEC 61000-4-13:2002+AMD1:2009+AMD2:2015 CSV | Electromagnetic compatibility (EMC) - Part 4-13: Testing and measurement techniques - Harmonics and interharmonics includingmains signalling at a.c. power port, low frequency immunity tests |
| BS EN 61439-1:2011 | Low-voltage switchgear and controlgear assemblies General rules |
| BS EN 60730-1:2011 | Automatic electrical controls for household and similar use General requirements |
| BS EN 50090-2-2 : 1997 | HOME AND BUILDING ELECTRONIC SYSTEMS (HBES) - PART 2-2: SYSTEM OVERVIEW - GENERAL TECHNICAL REQUIREMENTS |
| EN 50065-2-1 : 2003 AMD 1 2005 | SIGNALLING ON LOW-VOLTAGE ELECTRICAL INSTALLATIONS IN THE FREQUENCY RANGE 3 KHZ TO 148,5 KHZ - PART 2-1: IMMUNITY REQUIREMENTS FOR MAINS COMMUNICATIONS EQUIPMENT AND SYSTEMS OPERATING IN THE RANGE OF FREQUENCIES 95 KHZ TO 148,5 KHZ AND INTENDED FOR USE IN RESIDENTIAL, COMMERCIAL AND LIGHT INDUSTRIAL ENVIRONMENTS |
| EN 50065-2-2:2003/A1:2005/corrigendum Oct. 2006 | SIGNALING ON LOW-VOLTAGE ELECTRICAL INSTALLATIONS IN THE FREQUENCY RANGE 3 KHZ TO 148,5 KHZ - PART 2-2: IMMUNITY REQUIREMENTS FOR MAINS COMMUNICATIONS EQUIPMENT AND SYSTEMS OPERATING IN THE RANGE OF FREQUENCIES 95 KHZ TO 148,5 KHZ AND INTENDED FOR USE IN INDUSTRIAL ENVIRONMENTS |
| EN 61000-6-3 : 2007 : INC : AMD 1 : 2011 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-3: GENERIC STANDARDS - EMISSION STANDARD FOR RESIDENTIAL, COMMERCIAL AND LIGHT-INDUSTRIAL ENVIRONMENTS (IEC 61000-6-3:2006/A1:2010) |
| EN 62612:2013/A11:2017/AC:2017-11 | SELF-BALLASTED LED LAMPS FOR GENERAL LIGHTING SERVICES WITH SUPPLY VOLTAGES > 50 V - PERFORMANCE REQUIREMENTS |
| EN 61786-1:2014 | Measurement of DC magnetic, AC magnetic and AC electric fields from 1 Hz to 100 kHz with regard to exposure of human beings - Part 1: Requirements for measuring instruments |
| EN 61000-3-3:2013 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 3-3: LIMITS - LIMITATION OF VOLTAGE CHANGES, VOLTAGE FLUCTUATIONS AND FLICKER IN PUBLIC LOW-VOLTAGE SUPPLY SYSTEMS, FOR EQUIPMENT WITH RATED CURRENT <= 16 A PER PHASE AND NOT SUBJECT TO CONDITIONAL CONNECTION (IEC 61000-3-3:2013) |
| EN 62282-5-1:2012 | FUEL CELL TECHNOLOGIES - PART 5-1: PORTABLE FUEL CELL POWER SYSTEMS - SAFETY (IEC 62282-5-1:2012) |
| EN 61000-4-1:2007 | Electromagnetic compatibility (EMC) - Part 4-1: Testing and measurement techniques - Overview of IEC 61000-4 series |
| EN 50065-2-3 : 2003 AMD 1 2005 | SIGNALLING ON LOW-VOLTAGE ELECTRICAL INSTALLATIONS IN THE FREQUENCY RANGE 3 KHZ TO 148.5 KHZ - PART 2-3: IMMUNITY REQUIREMENTS FOR MAINS COMMUNICATIONS EQUIPMENT AND SYSTEMS OPERATING IN THE RANGE OF FREQUENCIES 3 KHZ TO 95 KHZ AND INTENDED FOR USE BY ELECTRICITY SUPPLIERS AND DISTRIBUTORS |
| EN 62282-3-201:2017 | Fuel cell technologies - Part 3-201: Stationary fuel cell power systems - Performance test methods for small fuel cell power systems |
| EN 55103-2:2009 | Electromagnetic compatibility - Product family standard for audio, video, audio-visual and entertainment lighting control apparatus for professional use - Part 2: Immunity |
| EN 61326:1997/A3:2003 | |
| EN 50090-2-2:1996/A2:2007 | HOME AND BUILDING ELECTRONIC SYSTEMS (HBES) - PART 2-2: SYSTEM OVERVIEW - GENERAL TECHNICAL REQUIREMENTS |
| EN 62041:2010 | Safety of transformers, reactors, power supply units and combinations thereof - EMC requirements |
| EN 60204-31:2013 | Safety of machinery - Electrical equipment of machines - Part 31: Particular safety and EMC requirements for sewing machines, units and systems |
| DIN EN 14637:2008-01 | Building hardware - Electrically controlled hold-open systems for fire/smoke door assemblies - Requirements, test methods, application and maintenance |
| EN 50512:2009 | Electrical installations for lighting and beaconing of aerodromes - Advanced Visual Docking Guidance Systems (A-VDGS) |
| EN 60146-1-1:2010 | Semiconductor converters - General requirements and line commutated converters - Part 1-1: Specification of basic requirements |
| EN 60439-1:1999/A1:2004 | LOW VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES - PART 1 - TYPE TESTED AND PARTIALLY TYPE TESTED ASSEMBLIES |
| EN 62135-2:2015 | Resistance welding equipment - Part 2: Electromagnetic compatibility (EMC) requirements |
| EN 62040-2:2006/corrigendum:2006 | |
| EN 50491-5-1:2010 | General requirements for Home and Building Electronic Systems (HBES) and Building Automation and Control Systems (BACS) - Part 5-1: EMC requirements, conditions and test set-up |
| EN 50240:2004/corrigendum:2005 | |
| EN 50438:2013 | REQUIREMENTS FOR MICRO-GENERATING PLANTS TO BE CONNECTED IN PARALLEL WITH PUBLIC LOW-VOLTAGE DISTRIBUTION NETWORKS |
| EN 60929:2011/A1:2016 | AC AND/OR DC-SUPPLIED ELECTRONIC CONTROL GEAR FOR TUBULAR FLUORESCENT LAMPS - PERFORMANCE REQUIREMENTS |
| EN 61000-4-7:2002/A1:2009 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-7: TESTING AND MEASUREMENT TECHNIQUES - GENERAL GUIDE ON HARMONICS AND INTERHARMONICS MEASUREMENTS AND INSTRUMENTATION, FOR POWER SUPPLY SYSTEMS AND EQUIPMENT CONNECTED THERETO (IEC 61000-4-7:2002/A1:2008) |
| DIN EN 61558-2-17 : 1998 | SAFETY OF POWER TRANSFORMERS, POWER SUPPLY UNITS AND SIMILAR - PART 2-17: PARTICULAR REQUIREMENTS FOR TRANSFORMERS FOR SWITCH MODE POWER SUPPLIES |
| EN 60947-5-9:2007 | Low-voltage switchgear and controlgear - Part 5-9: Control circuit devices and switching elements - Flow rate switches |
| EN 60974-10:2014/A1:2015 | ARC WELDING EQUIPMENT - PART 10: ELECTROMAGNETIC COMPATIBILITY (EMC) REQUIREMENTS (IEC 60974-10:2014/A1:2015) |
| EN 50107:1998 | Signs and luminous-discharge-tube installations operating from a no-load rated output voltage exceeding 1 kV but not exceeding 10 kV |
| EN 55103-1:2009/A1:2012 | ELECTROMAGNETIC COMPATIBILITY - PRODUCT FAMILY STANDARD FOR AUDIO, VIDEO, AUDIO-VISUAL AND ENTERTAINMENT LIGHTING CONTROL APPARATUS FOR PROFESSIONAL USE - PART 1: EMISSIONS |
| EN 62811:2015 | AC and/or DC-supplied electronic controlgear for discharge lamps (excluding fluorescent lamps) - Performance requirements for low frequency squarewave operation |
| UNE-EN 809:1999 | PUMPS AND PUMP UNITS FOR LIQUIDS - COMMON SAFETY REQUIREMENTS |
| IEC 60050-131:2002 | International Electrotechnical Vocabulary (IEV) - Part 131: Circuit theory |
| IEC 60107-1:1997 | Methods of measurement on receivers for television broadcast transmissions - Part 1: General considerations - Measurements at radio and video frequencies |
| IEC 60268-3:2013 | Sound system equipment - Part 3: Amplifiers |
| IEC 60335-2-24:2010+AMD1:2012+AMD2:2017 CSV | Household and similar electrical appliances - Safety - Part 2-24: Particular requirements for refrigerating appliances, ice-cream appliances and ice makers |
| IEC 60335-2-14:2016 | Household and similar electrical appliances - Safety - Part 2-14: Particular requirements for kitchen machines |
| IEC 61000-3-12:2011 | Electromagnetic compatibility (EMC) - Part 3-12: Limits - Limits for harmonic currents produced by equipment connected to public low-voltage systems with input current >16 A and ≤ 75 A per phase |
| 2004/108/EC : 2004 | DIRECTIVE 2004/108/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 15 DECEMBER 2004 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES RELATING TO ELECTROMAGNETIC COMPATIBILITY AND REPEALING DIRECTIVE 89/336/EC |
| EN 61000-4-7:2002/A1:2009 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-7: TESTING AND MEASUREMENT TECHNIQUES - GENERAL GUIDE ON HARMONICS AND INTERHARMONICS MEASUREMENTS AND INSTRUMENTATION, FOR POWER SUPPLY SYSTEMS AND EQUIPMENT CONNECTED THERETO (IEC 61000-4-7:2002/A1:2008) |
| EN 60335-2-79:2012 | Household and similar electrical appliances - Safety - Part 2-79: Particular requirements for high pressure cleaners and steam cleaners |
| EN 60335-2-24:2010 | Household and similar electrical appliances - Safety - Part 2-24: Particular requirements for refrigerating appliances, ice-cream appliances and ice makers |
| IEC 60974-6:2015 | Arc welding equipment - Part 6: Limited duty equipment |
| EN 61000-2-2:2002/A1:2017 | ELECTROMAGNETIC COMPATIBILITY (EMC) - ENVIRONMENT - COMPATIBILITY LEVELS FOR LOW-FREQUENCY CONDUCTED DISTURBANCES AND SIGNALLING IN PUBLIC LOW-VOLTAGE POWER SUPPLY SYSTEMS (IEC 61000-2-2:2002/A1:2017) |
| IEC 60335-2-2:2009+AMD1:2012+AMD2:2016 CSV | HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 2-2: PARTICULAR REQUIREMENTS FOR VACUUM CLEANERS AND WATER-SUCTION CLEANING APPLIANCES |
| IEC 60974-1:2017 | Arc welding equipment - Part 1: Welding power sources |
| EN 60268-3:2013 | Sound system equipment - Part 3: Amplifiers |
| IEC TS 61000-3-4:1998 | Electromagnetic compatibility (EMC) - Part 3-4: Limits - Limitation of emission of harmonic currents in low-voltage power supply systems for equipment with rated current greater than 16 A |
| IEC 61000-2-2:2002+AMD1:2017 CSV | Electromagnetic compatibility (EMC) - Part 2-2: Environment - Compatibility levels for low-frequency conducted disturbances and signalling in public low-voltage power supply systems |
| HD 483.1 : 200S2 | SOUND SYSTEM EQUIPMENT - GENERAL |
| IEC 60268-1:1985 | Sound system equipment. Part 1: General |
| IEC 60335-2-79:2016 | Household and similar electrical appliances - Safety - Part 2-79: Particular requirements for high pressure cleaners and steam cleaners |
| EN 61000-3-12:2011 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 3-12: LIMITS - LIMITS FOR HARMONIC CURRENTS PRODUCED BY EQUIPMENT CONNECTED TO PUBLIC LOW-VOLTAGE SYSTEMS WITH INPUT CURRENT > 16 A AND <= 75 A PER PHASE (IEC 61000-3-12:2011) |
| IEC 61000-4-7:2002+AMD1:2008 CSV | Electromagnetic compatibility (EMC) - Part 4-7: Testing and measurement techniques - General guide on harmonics and interharmonics measurements and instrumentation, for power supply systems and equipment connected thereto |
| EN 60155:1995/A2:2007 | GLOW-STARTERS FOR FLUORESCENT LAMPS |
| 119999/5/EC : 1999 | DIRECTIVE 1999/5/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 9 MARCH 1999 ON RADIO EQUIPMENT AND TELECOMMUNICATIONS TERMINAL EQUIPMENT AND THE MUTUAL RECOGNITION OF THEIR CONFORMITY |
| EN 60335-2-14:2006/A12:2016 | HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 2-14: PARTICULAR REQUIREMENTS FOR KITCHEN MACHINES (IEC 60335-2-14:2006, MODIFIED) |
| EN 60107-1:1997 | Methods of measurement on receivers for television broadcast transmissions - Part 1: General considerations - Measurements at radio and video frequencies |
| IEC 60155:1993 | Glow-starters for fluorescent lamps |
| EN 60335-2-2:2010/A1:2013 | HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 2-2: PARTICULAR REQUIREMENTS FOR VACUUM CLEANERS AND WATER-SUCTION CLEANING APPLIANCES (IEC 60335-2-2:2009/A1:2012) |
| EN 60974-1:2012 | Arc welding equipment - Part 1: Welding power sources |
Sorry this product is not available in your region.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.