EN 61212-2:2006
Current
The latest, up-to-date edition.
14-12-2006
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Conditioning of specimens
4 Dimensions
4.1 General
4.2 External diameter
4.3 Internal diameter
4.4 Wall thickness
4.5 Departure from straightness - Applicable
to all tubes up to 300 mm diameter
5 Mechanical tests
5.1 Flexural strength perpendicular to laminations
5.2 Axial compressive strength
5.3 Cohesion between layers
6 Electrical tests
6.1 Electric strength and breakdown voltage
6.2 Insulation resistance after immersion in water
6.3 Dissipation factor and permittivity (tube only)
7 Other tests
7.1 Thermal endurance
7.2 Water absorption
7.3 Density
7.4 Flammability
Annex ZA (normative) Normative references to
international publications with their
corresponding European publications
BIBLIOGRAPHY
This part of IEC 61212 describes methods of test for the materials defined in IEC 61212-1. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone.
| Committee |
CLC/SR 15
|
| DevelopmentNote |
Supersedes UNE EN 61212-2. (11/2009)
|
| DocumentType |
Standard
|
| PublisherName |
European Committee for Standards - Electrical
|
| Status |
Current
|
| Standards | Relationship |
| PN EN 61212-2 : 2007 | Identical |
| NEN 11212-2 : 1996 | Identical |
| IEC 61212-2:2006 | Identical |
| NF EN 61212-2 : 2011 | Identical |
| NEN EN IEC 61212-2 : 2007 | Identical |
| SN EN 61212-2 : 1996 | Identical |
| DIN EN 61212-2 : 1996 | Identical |
| UNE-EN 61212-2:2006 | Identical |
| VDE 0319-2 : 2007 | Identical |
| NBN EN 61212-2 : 2007 | Identical |
| DIN EN 61212-2:2007 | Identical |
| CEI EN 61212-2 : 2007 | Identical |
| UNE-EN 61212-2:1997 | Identical |
| BS EN 61212-2:2006 | Identical |
| I.S. EN 61212-2:2006 | Identical |
| EN 61212-3-2:2013 | Insulating materials - Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes - Part 3: Specifications for individual materials - Sheet 2: Round laminated moulded tubes |
| I.S. EN 61212-3-1:2013 | INSULATING MATERIALS - INDUSTRIAL RIGID ROUND LAMINATED TUBES AND RODS BASED ON THERMOSETTING RESINS FOR ELECTRICAL PURPOSES - PART 3: SPECIFICATIONS FOR INDIVIDUAL MATERIALS - SHEET 1: ROUND LAMINATED ROLLED TUBES (IEC 61212-3-1:2013 (EQV)) |
| I.S. EN 61212-3-2:2013 | INSULATING MATERIALS - INDUSTRIAL RIGID ROUND LAMINATED TUBES AND RODS BASED ON THERMOSETTING RESINS FOR ELECTRICAL PURPOSES - PART 3: SPECIFICATIONS FOR INDIVIDUAL MATERIALS - SHEET 2: ROUND LAMINATED MOULDED TUBES (IEC 61212-3-2:2013 (EQV)) |
| BS EN 61212-3-1:2013 | Insulating materials. Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes Specifications for individual materials. Sheet 1: Round laminated rolled tubes |
| BS EN 61212-3-2:2013 | Insulating materials. Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes Specifications for individual materials. Sheet 2: Round laminated moulded tubes |
| EN 62631-3-2:2016 | Dielectric and resistive properties of solid insulating materials - Part 3-2: Determination of resistive properties (DC Methods) - Surface resistance and surface resistivity |
| EN 61212-3-1:2013 | INSULATING MATERIALS - INDUSTRIAL RIGID ROUND LAMINATED TUBES AND RODS BASED ON THERMOSETTING RESINS FOR ELECTRICAL PURPOSES - PART 3: SPECIFICATIONS FOR INDIVIDUAL MATERIALS - SHEET 1: ROUND LAMINATED ROLLED TUBES (IEC 61212-3-1:2013) |
| IEC 60243-1:2013 | Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies |
| EN 61212-1:2006 | Insulating materials - Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes - Part 1: Definitions, designations and general requirements |
| EN ISO 62:2008 | Plastics - Determination of water absorption (ISO 62:2008) |
| EN 60216-1:2013 | Electrical insulating materials - Thermal endurance properties - Part 1: Ageing procedures and evaluation of test results |
| IEC 60212:2010 | Standard conditions for use prior to and during the testing of solid electrical insulating materials |
| IEC 60250:1969 | Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including metre wavelengths |
| HD 437 : 200S1 | STANDARD CONDITIONS FOR USE PRIOR TO AND DURING THE TESTING OF SOLID ELECTRICAL INSULATING MATERIALS |
| EN ISO 178:2010/A1:2013 | PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES (ISO 178:2010/AMD 1:2013) |
| EN ISO 604 : 2003 | PLASTICS - DETERMINATION OF COMPRESSIVE PROPERTIES (ISO 604:2002) |
| IEC 60216-2:2005 | Electrical insulating materials - Thermal endurance properties - Part 2: Determination of thermal endurance properties of electrical insulating materials - Choice of test criteria |
| EN 60216-2:2005 | Electrical insulating materials - Thermal endurance properties - Part 2: Determination of thermal endurance properties of electrical insulating materials - Choice of test criteria |
| IEC 60167:1964 | Methods of test for the determination of the insulation resistance of solid insulating materials |
| IEC 60296:2012 RLV | Fluids for electrotechnical applications - Unused mineral insulating oils for transformers and switchgear |
| ISO 6906:1984 | Vernier callipers reading to 0,02 mm |
| HD 568 : 200S1 | METHODS OF TEST FOR THE DETERMINATION OF THE INSULATION RESISTANCE OF SOLID INSULATING MATERIALS |
| ISO 1642:1987 | Plastics Industrial laminated sheets based on thermosetting resins Specification |
| EN 60296:2012 | Fluids for electrotechnical applications - Unused mineral insulating oils for transformers and switchgear |
| ISO 3599:1976 | Vernier callipers reading to 0,1 and 0,05 mm |
| IEC 60695-11-10:2013 | Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods |
| ISO 1183-1:2012 | Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method |
| ISO 604:2002 | Plastics — Determination of compressive properties |
| EN 60243-1:2013 | ELECTRIC STRENGTH OF INSULATING MATERIALS - TEST METHODS - PART 1: TESTS AT POWER FREQUENCIES (IEC 60243-1:2013) |
| ISO 3611:2010 | Geometrical product specifications (GPS) — Dimensional measuring equipment: Micrometers for external measurements — Design and metrological characteristics |
| ISO 62:2008 | Plastics Determination of water absorption |
| IEC 61212-1:2006 | Insulating materials - Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes - Part 1: Definitions, designations and general requirements |
| ISO 178:2010 | Plastics Determination of flexural properties |
| IEC 60216-1:2013 | Electrical insulating materials - Thermal endurance properties - Part 1: Ageing procedures and evaluation of test results |
| EN ISO 1183-1:2012 | Plastics - Methods for determining the density of non-cellular plastics - Part 1: Immersion method, liquid pyknometer method and titration method (ISO 1183-1:2012) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.