Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

EN 61290-1-1:2015

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Optical amplifiers - Test methods - Part 1-1: Power and gain parameters - Optical spectrum analyzer method
Superseded date

31-10-2020

Published date

10-07-2015

FOREWORD
1 Scope
2 Normative references
3 Terms, definitions and abbreviations
4 Apparatus
5 Test sample
6 Procedure
7 Calculation
8 Test results
Bibliography
Annex ZA (normative) - Normative references to international
         Publications with their corresponding European
         publications

IEC 61290-1-1:2015(E) applies to all commercially available optical amplifiers (OAs) and optically amplified modules. It applies to OAs using optically pumped fibres (OFAs based on either rare-earth doped fibres or on the Raman effect), semiconductor OAs (SOAs) and planar optical waveguide amplifiers (POWAs). The object of this standard is to establish uniform requirements for accurate and reliable measurements, by means of the optical spectrum analyzer test method, of the following OA parameters, as defined in IEC 61291-1:- nominal output signal power;- gain;- polarization-dependent gain;- maximum output signal power;- maximum total output power. The object of this standard is specifically directed to single-channel amplifiers. For multichannel amplifiers, one should refer to the IEC 61290-10 series. This third edition cancels and replaces the second edition published in 2006 and constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: updates on the characteristics of measurement apparatus and revised list of addressed optical amplifier parameters.Keywords: optical amplifiers, optical spectrum analyzer test, single-channel amplifiers

Committee
CLC/SR 86C
DevelopmentNote
Supersedes EN 61290-2-1. (11/2006)
DocumentType
Standard
PublisherName
European Committee for Standards - Electrical
Status
Superseded
SupersededBy
Supersedes

I.S. EN 61291-1:2012 OPTICAL AMPLIFIERS - PART 1: GENERIC SPECIFICATION (IEC 61291-1:2012 (EQV))
EN 61290-1:2015 Optical amplifiers - Test methods - Part 1: Power and gain parameters
BS EN 61291-1:2012 Optical amplifiers Generic specification
EN 61290-1-3:2015 Optical amplifiers - Test methods - Part 1-3: Power and gain parameters - Optical power meter method
CEI EN 61291-1 : 2013 OPTICAL AMPLIFIERS - PART 1: GENERIC SPECIFICATION
I.S. EN 61290-3-1:2003 OPTICAL AMPLIFIERS - TEST METHODS - PART 3-1: NOISE FIGURE PARAMETERS - OPTICAL SPECTRUM ANALYZER METHOD
BS EN 61290-10-1:2009 Optical amplifiers. Test methods Multichannel parameters. Pulse method using an optical switch and optical spectrum analyzer
BS EN 61290-4-2:2011 Optical amplifiers. Test methods Gain transient parameters. Broadband source method
BS EN 61290-1:2015 Optical amplifiers. Test methods Power and gain parameters
BS EN 61290-3-1:2003 Optical fibre amplifiers. Basic specification. Test methods for noise figure parameters Optical spectrum analyzer method
BS EN 61290-1-3:2015 Optical amplifiers. Test methods Power and gain parameters. Optical power meter method
I.S. EN 61290-1:2015 OPTICAL AMPLIFIERS - TEST METHODS - PART 1: POWER AND GAINPARAMETERS
EN 61290-10-1:2009 Optical amplifiers - Test methods - Part 10-1: Multichannel parameters - Pulse method using an optical switch and optical spectrum analyzer
EN 61290-3-1:2003 Optical amplifiers - Test methods - Part 3-1: Noise figure parameters - Optical spectrum analyzer method
EN 61290-4-2:2011 Optical amplifiers - Test methods - Part 4-2: Gain transient parameters - Broadband source method
EN 61291-1:2012 Optical amplifiers - Part 1: Generic specification

EN 61291-1:2012 Optical amplifiers - Part 1: Generic specification
EN 60793-2-50:2016 Optical fibres - Part 2-50: Product specifications - Sectional specification for class B single-mode fibres
EN 61290-1:2015 Optical amplifiers - Test methods - Part 1: Power and gain parameters
IEC 61290-1:2014 Optical amplifiers - Test methods - Part 1: Power and gain parameters
IEC 61291-1:2012 Optical amplifiers - Part 1: Generic specification
IEC 60793-2-50:2015 Optical fibres - Part 2-50: Product specifications - Sectional specification for class B single-mode fibres

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more