EN 61810-1:2015/AC:2018-04

Superseded

View Superseded by

ELECTROMECHANICAL ELEMENTARY RELAYS - PART 1: GENERAL AND SAFETY REQUIREMENTS (IEC 61810-1:2015/COR1:2018)

Superseded date

17-03-2020

Published date

12-01-2013

Publisher

European Committee for Standards - Electrical

FOREWORD
1 Scope
2 Normative references
3 Terms and definitions
4 Influence quantities
5 Rated values
6 General provisions for testing
7 Documentation and marking
8 Heating
9 Basic operating function
10 Dielectric strength
11 Electrical endurance
12 Mechanical endurance
13 Clearances, creepage distances and solid insulation
14 Terminations
15 Sealing
16 Heat and fire resistance
Annex A (normative) - Explanations regarding relays
Annex B (informative) - Inductive contact loads
Annex C (normative) - Test set-up
Annex D (informative) - Special loads
Annex E (normative) - Heating test arrangement
Annex F (normative) - Measurement of clearances and
        creepage distances
Annex G (normative) - Relation between rated impulse
        voltage, nominal voltage and overvoltage category
Annex H (normative) - Pollution degrees
Annex I (normative) - Proof tracking test
Annex J (informative) - Schematic diagram of families
        of terminations
Annex K (normative) - Glow-wire test
Annex L (normative) - Ball pressure test
Annex M (informative) - Needle flame test
Annex N (informative) - Resistance for standard
        soldering processes
Annex O (informative) - Risk assessment
Alphabetical list of terms
Bibliography
Annex ZA (normative) - Normative references to
         international publications with their
         corresponding European publications

Pertains to electromechanical elementary relays (non-specified time all or-nothing relays) for incorporation into low voltage equipment (circuits up to 1000 V alternate current or 1500 V direct current).

Committee	TC 94
DevelopmentNote	Supersedes EN 60255-1-00 (04/2001) Supersedes EN 61810-5 (03/2004)
DocumentType	Standard
PublisherName	European Committee for Standards - Electrical
Status	Superseded
SupersededBy	EN 61810-1 : 2015 : INC : AMD 1 : 2020
Supersedes	EN 61810-1:2015

Standards	Relationship
IEC 61810-1:2015	Identical
CEI EN 61810-1 : 2016/EC:2018	Identical
NF EN 61810-1 : 2015	Identical
NBN EN 61810-1 : 2015	Identical
UNE-EN 61810-1:2009	Identical
PN EN 61810-1 : 2015 AC 2017	Identical
SN EN 61810-1 : 1998	Identical
NEN EN IEC 61810-1 : 2015 C1 2017	Identical
I.S. EN 61810-1:2015	Identical
CEI EN 61810-1 : 2016	Identical
BS EN 61810-1:2015	Identical
CEI EN 61810-1:2016/EC:2019	Identical

IEC 60950-1:2005+AMD1:2009+AMD2:2013 CSV	Information technology equipment - Safety - Part 1: General requirements
IEC 60112:2003+AMD1:2009 CSV	Method for the determination of the proof and the comparative tracking indices of solid insulating materials
IEC 60038:2009	IEC standard voltages
IEC 60664-4:2005	Insulation coordination for equipment within low-voltage systems - Part 4: Consideration of high-frequency voltage stress
IEC 61984:2008	Connectors - Safety requirements and tests
IEC 60068-2-20:2008	Environmental testing - Part 2-20: Tests - Test T: Test methods for solderability and resistance to soldering heat of devices with leads
EN 60085:2008	Electrical insulation - Thermal evaluation and designation
EN 60068-2-20:2008	Environmental testing - Part 2-20: Tests - Test T: Test methods for solderability and resistance to soldering heat of devices with leads
EN 60695-10-2:2014	Fire hazard testing - Part 10-2: Abnormal heat - Ball pressure test method
EN 60079-15:2010	Explosive atmospheres - Part 15: Equipment protection by type of protection "n"
EN 60068-2-2:2007	Environmental testing - Part 2-2: Tests - Test B: Dry heat
IEC 61210:2010	Connecting devices - Flat quick-connect terminations for electrical copper conductors - Safety requirements
EN 61760-1:2006	SURFACE MOUNTING TECHNOLOGY - PART 1: STANDARD METHOD FOR THE SPECIFICATION OF SURFACE MOUNTING COMPONENTS (SMDS)
IEC 60947-5-1 : 4.0	LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 5-1: CONTROL CIRCUIT DEVICES AND SWITCHING ELEMENTS - ELECTROMECHANICAL CONTROL CIRCUIT DEVICES
IEC 61760-1:2006	Surface mounting technology - Part 1: Standard method for the specification of surface mounting components (SMDs)
IEC 60695-2-11:2014	Fire hazard testing - Part 2-11: Glowing/hot-wire based test methods - Glow-wire flammability test method for end-products (GWEPT)
ANSI B11 TR3 : 2000	RISK ASSESSMENT AND RISK REDUCTION - A GUIDE TO ESTIMATE, EVALUATE AND REDUCE RISKS ASSOCIATED WITH MACHINE TOOLS
EN 60099-1:1994/A1:1999	SURGE ARRESTERS - PART 1: NON-LINEAR RESISTOR TYPE GAPPED SURGE ARRESTERS FOR A.C. SYSTEMS
IEC 60695-2-13:2010+AMD1:2014 CSV	Fire hazard testing - Part 2-13: Glowing/hot-wire based test methods- Glow-wire ignition temperature (GWIT) test method for materials
IEC 61810-7:2006	Electromechanical elementary relays - Part 7: Test and measurement procedures
EN 60112 : 2003 AMD 1 2009	METHOD FOR THE DETERMINATION OF THE PROOF AND THE COMPARATIVE TRACKING INDICES OF SOLID INSULATING MATERIALS
IEC 60999-1:1999	Connecting devices - Electrical copper conductors - Safety requirements for screw-type and screwless-type clamping units - Part 1: General requirements and particular requirements for clamping units for conductors from 0,2 mm2 up to 35 mm2 (included)
HD 60364-4-442:2012	Low-voltage electrical installations - Part 4-442: Protection for safety - Protection of low-voltage installations against temporary overvoltages due to earth faults in the high-voltage system and due to faults in the low voltage system
EN 60695-2-13:2010/A1:2014	FIRE HAZARD TESTING - PART 2-13: GLOWING/HOT-WIRE BASED TEST METHODS - GLOW-WIRE IGNITION TEMPERATURE (GWIT) TEST METHOD FOR MATERIALS (IEC 60695-2-13:2010/A1:2014)
IEC 60085:2007	Electrical insulation - Thermal evaluation and designation
IEC 60695-2-12:2010+AMD1:2014 CSV	Fire hazard testing - Part 2-12: Glowing/hot-wire based test methods- Glow-wire flammability index (GWFI) test method for materials
SEMI S10 : 2015E	SAFETY GUIDELINE FOR RISK ASSESSMENT AND RISK EVALUATION PROCESS
EN 60068-2-17:1994	Environmental testing - Part 2: Tests - Test Q: Sealing
IEC 60068-2-17:1994	Basic environmental testing procedures - Part 2-17: Tests - Test Q: Sealing
EN 60695-2-10:2013	Fire hazard testing - Part 2-10: Glowing/hot-wire based test methods - Glow-wire apparatus and common test procedure
IEC 60364-4-44:2007+AMD1:2015 CSV	Low-voltage electrical installations - Part 4-44: Protection for safety - Protection against voltage disturbances and electromagnetic disturbances
IEC 60099-1:1991+AMD1:1999 CSV	Surge arresters - Part 1: Non-linear resistor type gapped surge arresters for a.c. systems
IEC 60068-2-2:2007	Environmental testing - Part 2-2: Tests - Test B: Dry heat
EN 60664-1:2007	Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests
IEC 60669-1:2017	Switches for household and similar fixed-electrical installations - Part 1: General requirements
IEC 60664-5:2007	Insulation coordination for equipment within low-voltage systems - Part 5: Comprehensive method for determining clearances and creepage distances equal to or less than 2 mm
IEC 60721-3-3:1994+AMD1:1995+AMD2:1996 CSV	Classification of environmental conditions - Part 3-3: Classification of groups of environmental parameters and their severities - Stationary use at weatherprotected locations
EN 61210:2010	Connecting devices - Flat quick-connect terminations for electrical copper conductors - Safety requirements
IEC 60664-3:2016	Insulation coordination for equipment within low-voltage systems - Part 3: Use of coating, potting or moulding for protection against pollution
EN 60999-1:2000	Connecting devices - Electrical copper conductors - Safety requirements for screw-type and screwless-type clamping units - Part 1: General requirements and particular requirements for clamping units for conductors from 0,2 mm² up to 35 mm² (included)
EN 61984:2009	Connectors - Safety requirements and tests
IEC 60695-10-2:2014	Fire hazard testing - Part 10-2: Abnormal heat - Ball pressure test method
EN 60664-4:2006/corrigendum:2006	INSULATION COORDINATION FOR EQUIPMENT WITHIN LOW-VOLTAGE SYSTEMS - PART 4: CONSIDERATION OF HIGH-FREQUENCY VOLTAGE STRESS
IEC 61140:2016	Protection against electric shock - Common aspects for installation and equipment
EN 60664-5:2007	Insulation coordination for equipment within low-voltage systems - Part 5: Comprehensive method for determining clearances and creepage distances equal to or less than 2 mm
IEC 60695-11-5 : 2.0	FIRE HAZARD TESTING - PART 11-5: TEST FLAMES - NEEDLE-FLAME TEST METHOD - APPARATUS, CONFIRMATORY TEST ARRANGEMENT AND GUIDANCE
IEC 60695-11-5:2016	Fire hazard testing - Part 11-5: Test flames - Needle-flame test method - Apparatus, confirmatory test arrangement and guidance
IEC 60695-2-10:2013	Fire hazard testing - Part 2-10: Glowing/hot-wire based test methods - Glow-wire apparatus and common test procedure
EN 60695-2-12:2010/A1:2014	FIRE HAZARD TESTING - PART 2-12: GLOWING/HOT-WIRE BASED TEST METHODS - GLOW-WIRE FLAMMABILITY INDEX (GWFI) TEST METHOD FOR MATERIALS (IEC 60695-2-12:2010/A1:2014)
IEC 60664-1:2007	Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests
EN 60664-3:2017	Insulation coordination for equipment within low-voltage systems - Part 3: Use of coating, potting or moulding for protection against pollution
IEC 60079-15:2010	Explosive atmospheres - Part 15: Equipment protection by type of protection "n"
EN 60038 : 2011	CENELEC STANDARD VOLTAGES (IEC 60038:2009, MODIFIED)
EN 60695-2-11:2014	Fire hazard testing - Part 2-11: Glowing/hot-wire based test methods - Glow-wire flammability test method for end-products (GWEPT) (IEC 60695-2-11:2014)
IEC 60730-1:2013+AMD1:2015 CSV	Automatic electrical controls - Part 1: General requirements
EN 60721-3-3 : 95 AMD 2 97	CLASSIFICATION OF ENVIRONMENTAL CONDITIONS - CLASSIFICATION OF GROUPS OF ENVIRONMENTAL PARAMETERS AND THEIR SEVERITIES - STATIONARY USE AT WEATHER-PROTECTED LOCATIONS