EN 62109-1 : 2010
Current
Current
The latest, up-to-date edition.
SAFETY OF POWER CONVERTERS FOR USE IN PHOTOVOLTAIC POWER SYSTEMS - PART 1: GENERAL REQUIREMENTS
Published date
16-07-2010
FOREWORD
INTRODUCTION
1 Scope and object
2 Normative references
3 Terms and definitions
4 General testing requirements
5 Marking and documentation
6 Environmental requirements and conditions
7 Protection against electric shock and energy hazards
8 Protection against mechanical hazards
9 Protection against fire hazards
10 Protection against sonic pressure hazards
11 Protection against liquid hazards
12 Chemical hazards
13 Physical requirements
14 Components
15 Software and firmware performing safety functions
Annex A (normative) - Measurement of clearances and creepage
distances
Annex B (normative) - Programmable equipment
Annex C (normative) - Symbols to be used in equipment markings
Annex D (informative) - Test probes for determining access
Annex E (informative) - RCDs
Annex F (informative) - Altitude correction for clearances
Annex G (informative) - Clearance and creepage distance
determination for frequencies greater than 30 kHz
Annex H (informative) - Measuring instrument for touch current
measurements
Annex I (informative) - Examples of protection, insulation, and
overvoltage category requirements for PCE
Annex J (normative) - Ultraviolet light conditioning test
Annex ZA (normative) - Normative references to international
publications with their corresponding European
publications
IEC 62109-1:2010(E) applies to the power conversion equipment (PCE) for use in photovoltaic systems where a uniform technical level with respect to safety is necessary.
| Committee |
TC 82
|
| DocumentType |
Standard
|
| PublisherName |
European Committee for Standards - Electrical
|
| Status |
Current
|
| Standards | Relationship |
| IEC 62109-1:2010 | Identical |
| NBN EN 62109-1 : 2010 | Identical |
| NEN EN IEC 62109-1 : 2010 | Identical |
| I.S. EN 62109-1:2010 | Identical |
| PN EN 62109-1 : 2010 | Identical |
| DIN EN 62109-1 : 2011 COR 2 2013 | Identical |
| VDE 0126-14-1 : 2011 COR 2 2013 | Identical |
| UNE-EN 62109-1:2011 | Identical |
| BS EN 62109-1:2010 | Identical |
| CEI EN 62109-1 : 2010 | Identical |
| I.S. EN 50524:2009 | DATA SHEET AND NAME PLATE FOR PHOTOVOLTAIC INVERTERS |
| EN 62253 : 2011 | PHOTOVOLTAIC PUMPING SYSTEMS - DESIGN QUALIFICATION AND PERFORMANCE MEASUREMENTS |
| CEI EN 62109-2 : 2012 | SAFETY OF POWER CONVERTERS FOR USE IN PHOTOVOLTAIC POWER SYSTEMS - PART 2: PARTICULAR REQUIREMENTS FOR INVERTERS |
| S.R. CLC/TS 50549-2:2015 | REQUIREMENTS FOR GENERATING PLANTS TO BE CONNECTED IN PARALLEL WITH DISTRIBUTION NETWORKS - PART 2: CONNECTION TO A MV DISTRIBUTION NETWORK |
| S.R. HD 60364-7-712:2016 | LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 7-712: REQUIREMENTS FOR SPECIAL INSTALLATIONS OR LOCATIONS - PHOTOVOLTAIC (PV) SYSTEMS |
| EN IEC 62909-1:2018 | Bi-directional grid-connected power converters - Part 1: General requirements |
| BS EN 62253:2011 | Photovoltaic pumping systems. Design qualification and performance measurements |
| I.S. EN IEC 62909-1:2018 | BI-DIRECTIONAL GRID-CONNECTED POWER CONVERTERS - PART 1: GENERAL REQUIREMENTS |
| UNE-HD 60364-7-712:2017 | Low-voltage electrical installations - Part 7-712: Requirements for special installations or locations - Photovoltaic (PV) systems |
| CLC/TS 50539-12:2013 | Low-voltage surge protective devices - Surge protective devices for specific application including d.c. - Part 12: Selection and application principles - SPDs connected to photovoltaic installations |
| CEI EN 50524 : 2010 | DATA SHEET AND NAME PLATE FOR PHOTOVOLTAIC INVERTERS |
| BS EN 50524:2009 | Data sheet and name plate for photovoltaic inverters |
| CLC/TS 50549-2:2015 | Requirements for generating plants to be connected in parallel with distribution networks - Part 2: Connection to a MV distribution network |
| EN 50524:2009 | Data sheet and name plate for photovoltaic inverters |
| UNE-EN 62253:2012 | Photovoltaic pumping systems - Design qualification and performance measurements |
| PD CLC/TS 50539-12:2013 | Low-voltage surge protective devices. Surge protective devices for specific application including d.c. Selection and application principles. SPDs connected to photovoltaic installations |
| BS EN 62109-2:2011 | Safety of power converters for use in photovoltaic power systems Particular requirements for inverters |
| S.R. CLC/TS 50539-12:2013 | LOW-VOLTAGE SURGE PROTECTIVE DEVICES - SURGE PROTECTIVE DEVICES FOR SPECIFIC APPLICATION INCLUDING D.C. - PART 12: SELECTION AND APPLICATION PRINCIPLES - SPDS CONNECTED TO PHOTOVOLTAIC INSTALLATIONS |
| UNE-EN 62109-2:2013 | Safety of power converters for use in photovoltaic power systems - Part 2: Particular requirements for inverters |
| I.S. EN 62109-2:2011 | SAFETY OF POWER CONVERTERS FOR USE IN PHOTOVOLTAIC POWER SYSTEMS - PART 2: PARTICULAR REQUIREMENTS FOR INVERTERS (IEC 62109-2:2011 (EQV)) |
| I.S. EN 62253:2011 | PHOTOVOLTAIC PUMPING SYSTEMS - DESIGN QUALIFICATION AND PERFORMANCE MEASUREMENTS |
| UNE-EN 50524:2010 | Data sheet and name plate for photovoltaic inverters |
| EN 62109-2:2011 | Safety of power converters for use in photovoltaic power systems - Part 2: Particular requirements for inverters |
| HD 60364-7-712:2016 | Low-voltage electrical installations - Part 7-712: Requirements for special installations or locations - Photovoltaic (PV) systems |
| IEC 60695-11-20:2015 | Fire hazard testing - Part 11-20: Test flames - 500 W flame test method |
| IEC 60950-1:2005+AMD1:2009+AMD2:2013 CSV | Information technology equipment - Safety - Part 1: General requirements |
| IEC 60112:2003+AMD1:2009 CSV | Method for the determination of the proof and the comparative tracking indices of solid insulating materials |
| ISO 4892-1:2016 | Plastics Methods of exposure to laboratory light sources Part 1: General guidance |
| IEC 60364-5-54:2011 | Low-voltage electrical installations - Part 5-54: Selection and erection of electrical equipment - Earthing arrangements and protective conductors |
| IEC 60245-1:2003+AMD1:2007 CSV | Rubber insulated cables - Rated voltages up to and including 450/750 V - Part 1: General requirements |
| EN 60216-1:2013 | Electrical insulating materials - Thermal endurance properties - Part 1: Ageing procedures and evaluation of test results |
| EN ISO 8256:2004 | Plastics - Determination of tensile-impact strength (ISO 8256:2004) |
| IEC 60664-4:2005 | Insulation coordination for equipment within low-voltage systems - Part 4: Consideration of high-frequency voltage stress |
| EN ISO 180:2000/A2:2013 | PLASTICS - DETERMINATION OF IZOD IMPACT STRENGTH (ISO 180:2000/AMD 2:2013) |
| IEC 60216-6:2006 | Electrical insulating materials - Thermal endurance properties - Part 6: Determination of thermal endurance indices (TI and RTE) of an insulating material using the fixed time frame method |
| EN 62020:1998/A1:2005 | ELECTRICAL ACCESSORIES - RESIDUAL CURRENT MONITORS FOR HOUSEHOLD AND SIMILAR USES (RCMS) |
| EN ISO 4892-1:2016 | Plastics - Methods of exposure to laboratory light sources - Part 1: General guidance (ISO 4892-1:2016) |
| EN 60085:2008 | Electrical insulation - Thermal evaluation and designation |
| ISO 9614-1:1993 | Acoustics — Determination of sound power levels of noise sources using sound intensity — Part 1: Measurement at discrete points |
| EN 60950-1:2006/A2:2013 | INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60950-1:2005/A2:2013, MODIFIED) |
| HD 60364-5-54:2011/A11:2017 | LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 5-54: SELECTION AND ERECTION OF ELECTRICAL EQUIPMENT - EARTHING ARRANGEMENTS AND PROTECTIVE CONDUCTORS |
| IEC 60216-4-1:2006 | Electrical insulating materials - Thermal endurance properties - Part 4-1: Ageing ovens - Single-chamber ovens |
| EN ISO 178:2010/A1:2013 | PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES (ISO 178:2010/AMD 1:2013) |
| ISO 8256:2004 | Plastics — Determination of tensile-impact strength |
| IEC 60695-2-11:2014 | Fire hazard testing - Part 2-11: Glowing/hot-wire based test methods - Glow-wire flammability test method for end-products (GWEPT) |
| ISO 9614-2:1996 | Acoustics — Determination of sound power levels of noise sources using sound intensity — Part 2: Measurement by scanning |
| IEC 60216-2:2005 | Electrical insulating materials - Thermal endurance properties - Part 2: Determination of thermal endurance properties of electrical insulating materials - Choice of test criteria |
| HD 588.1 : S1 AMD 1 | HIGH VOLTAGE TEST TECHNIQUES - GENERAL DEFINITIONS AND TEST REQUIREMENTS |
| EN 60216-3:2006 | ELECTRICAL INSULATING MATERIALS - THERMAL ENDURANCE PROPERTIES - PART 3: INSTRUCTIONS FOR CALCULATING THERMAL ENDURANCE CHARACTERISTICS |
| IEC 60364-1:2005 | Low-voltage electrical installations - Part 1: Fundamental principles, assessment of general characteristics, definitions |
| IEC 60227-1:2007 | Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V - Part 1: General requirements |
| EN 60112 : 2003 AMD 1 2009 | METHOD FOR THE DETERMINATION OF THE PROOF AND THE COMPARATIVE TRACKING INDICES OF SOLID INSULATING MATERIALS |
| EN 60216-2:2005 | Electrical insulating materials - Thermal endurance properties - Part 2: Determination of thermal endurance properties of electrical insulating materials - Choice of test criteria |
| IEC 60085:2007 | Electrical insulation - Thermal evaluation and designation |
| ISO 262:1998 | ISO general purpose metric screw threads — Selected sizes for screws, bolts and nuts |
| ISO 3746:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Survey method using an enveloping measurement surface over a reflecting plane |
| HD 60364-1:2008/A11:2017 | LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 1: FUNDAMENTAL PRINCIPLES, ASSESSMENT OF GENERAL CHARACTERISTICS, DEFINITIONS |
| ISO 180:2000 | Plastics Determination of Izod impact strength |
| EN ISO 3746:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Survey method using an enveloping measurement surface over a reflecting plane (ISO 3746:2010) |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| IEC 60755:2017 | General safety requirements for residual current operated protective devices |
| EN 60216-5:2008 | Electrical insulating materials - Thermal endurance properties - Part 5: Determination of relative thermal endurance index (RTE) of an insulating material |
| IEC 60695-11-10:2013 | Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods |
| EN 61032:1998 | Protection of persons and equipment by enclosures - Probes for verification |
| EN 60664-1:2007 | Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests |
| ISO 9614-3:2002 | Acoustics — Determination of sound power levels of noise sources using sound intensity — Part 3: Precision method for measurement by scanning |
| ISO 4892-4:2013 | Plastics — Methods of exposure to laboratory light sources — Part 4: Open-flame carbon-arc lamps |
| EN ISO 9614-2 : 1996 | ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS OF NOISE SOURCES USING SOUND INTENSITY - PART 2: MEASUREMENT BY SCANNING |
| IEC 62020:1998+AMD1:2003 CSV | Electrical accessories - Residual current monitors for household and similar uses (RCMs) |
| ISO 4892-2:2013 | Plastics — Methods of exposure to laboratory light sources — Part 2: Xenon-arc lamps |
| ISO 261:1998 | ISO general purpose metric screw threads General plan |
| IEC 60664-3:2016 | Insulation coordination for equipment within low-voltage systems - Part 3: Use of coating, potting or moulding for protection against pollution |
| EN 60216-4-1:2006 | Electrical insulating materials - Thermal endurance properties - Part 4-1: Ageing ovens - Single-chamber ovens |
| EN ISO 9614-3:2009 | Acoustics - Determination of sound power levels of noise sources using sound intensity - Part 3: Precision method for measurement by scanning (ISO 9614-3:2002) |
| IEC 61180-1:1992 | High-voltage test techniques for low voltage equipment - Part 1: Definitions, test and procedure requirements |
| EN 60664-4:2006/corrigendum:2006 | INSULATION COORDINATION FOR EQUIPMENT WITHIN LOW-VOLTAGE SYSTEMS - PART 4: CONSIDERATION OF HIGH-FREQUENCY VOLTAGE STRESS |
| EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
| ISO 7000:2014 | Graphical symbols for use on equipment Registered symbols |
| IEC 60060-1:2010 | High-voltage test techniques - Part 1: General definitions and test requirements |
| IEC 60216-5:2008 | Electrical insulating materials - Thermal endurance properties - Part 5: Determination of relative thermal endurance index (RTE) of an insulating material |
| EN 60695-11-5:2017 | Fire hazard testing - Part 11-5: Test flames - Needle-flame test method - Apparatus, confirmatory test arrangement and guidance |
| IEC 61032:1997 | Protection of persons and equipment by enclosures - Probes for verification |
| IEC 60695-11-5 : 2.0 | FIRE HAZARD TESTING - PART 11-5: TEST FLAMES - NEEDLE-FLAME TEST METHOD - APPARATUS, CONFIRMATORY TEST ARRANGEMENT AND GUIDANCE |
| ISO 178:2010 | Plastics Determination of flexural properties |
| EN ISO 9614-1:2009 | Acoustics - Determination of sound power levels of noise sources using sound intensity - Part 1: Measurement at discrete points (ISO 9614-1:1993) |
| IEC 60664-1:2007 | Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests |
| EN ISO 4892-2:2013 | Plastics - Methods of exposure to laboratory light sources - Part 2: Xenon-arc lamps (ISO 4892-2:2013) |
| IEC 60216-1:2013 | Electrical insulating materials - Thermal endurance properties - Part 1: Ageing procedures and evaluation of test results |
| EN 60664-3:2017 | Insulation coordination for equipment within low-voltage systems - Part 3: Use of coating, potting or moulding for protection against pollution |
| ASTM E 162 : 2016 : REDLINE | Standard Test Method for Surface Flammability of Materials Using a Radiant Heat Energy Source |
| EN 60216-6:2006 | Electrical insulating materials - Thermal endurance properties - Part 6: Determination of thermal endurance indices (TI and RTE) of an insulating material using the fixed time frame method |
| EN 61180-1:1994 | High-voltage test techniques for low-voltage equipment - Part 1: Definitions, test and procedure requirements |
| IEC 60216-3:2006 | Electrical insulating materials - Thermal endurance properties - Part 3: Instructions for calculating thermal endurance characteristics |
| IEC 60990:2016 | Methods of measurement of touch current and protective conductor current |
| EN 60730-1:2016 | Automatic electrical controls - Part 1: General requirements |
| EN 60695-2-11:2014 | Fire hazard testing - Part 2-11: Glowing/hot-wire based test methods - Glow-wire flammability test method for end-products (GWEPT) (IEC 60695-2-11:2014) |
| IEC 60730-1:2013+AMD1:2015 CSV | Automatic electrical controls - Part 1: General requirements |
| EN 60990:2016 | Methods of measurement of touch current and protective conductor current |
Sorry this product is not available in your region.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.