Customer Support: 131 242

i2i Intertek.com
  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Go to AMERICAS site
Dismiss alert
Please enter a keyword to search
Advanced search
Home
CENELEC
EN 62196-2:2017

EN 62196-2:2017

Current

Current

The latest, up-to-date edition.

Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 2: Dimensional compatibility and interchangeability requirements for a.c. pin and contact-tube accessories

Published date

28-04-2017

Publisher

European Committee for Standards - Electrical

FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 General
5 Ratings
6 Connection between the power supply and the
   electric vehicle
7 Classification of accessories
8 Marking
9 Dimensions
10 Protection against electric shock
11 Size and colour of protective earthing conductors
12 Provision for earthing
13 Terminals
14 Interlocks
15 Resistance to ageing of rubber and thermoplastic
   material
16 General construction
17 Construction of socket-outlets
18 Construction of plugs and vehicle connectors
19 Construction of vehicle inlets
20 Degrees of protection
21 Insulation resistance and dielectric strength
22 Breaking capacity
23 Normal operation
24 Temperature rise
25 Flexible cables and their connection
26 Mechanical strength
27 Screws, current-carrying parts and connections
28 Creepage distances, clearances and distances
29 Resistance to heat, to fire and to tracking
30 Corrosion and resistance to rusting
31 Conditional short-circuit current withstand test
32 Electromagnetic compatibility (EMC)
33 Vehicle driveover
201 Components
202 Resistor coding
STANDARD SHEETS
CONFIGURATION TYPE 1
CONFIGURATION TYPE 2
CONFIGURATION TYPE 3
Annex ZA (normative) - Normative references to
         international publications with their
         corresponding European publications

IEC 62196-2:2016 applies to plugs, socket-outlets, vehicle connectors and vehicle inlets with pins and contact-tubes of standardized configurations, herein referred to as accessories. They have a nominal rated operating voltage not exceeding 480 V a.c., 50 Hz to 60 Hz, and a rated current not exceeding 63 A three-phase or 70 A single phase, for use in conductive charging of electric vehicles. This second edition cancels and replaces the first edition published in 2011 and constitutes a technical revision. This second edition includes the following significant technical changes with respect to the previous edition.

a) Standard sheets for configurations type 2 and type 3 have been updated.

b) Configuration type 2 is now available with optional shutter.


This publication is to be read in conjunction with IEC 62196-1:2014.

DocumentType
Standard
PublisherName
European Committee for Standards - Electrical
Status
Current

EN 62196-3:2014 Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 3: Dimensional compatibility and interchangeability requirements for d.c. and a.c./d.c. pin and contact-tube vehicle couplers
UNE-HD 60364-7-722:2016 Low-voltage electrical installations - Part 7-722: Requirements for special installations or locations - Supplies for electric vehicles
I.S. EN 62752:2016&AC:2019-03 IN-CABLE CONTROL AND PROTECTION DEVICE FOR MODE 2 CHARGING OF ELECTRIC ROAD VEHICLES (IC-CPD)
HD 60364-7-722:2016 Low-voltage electrical installations - Part 7-722: Requirements for special installations or locations - Supplies for electric vehicles
I.S. EN 62196-3:2014 PLUGS, SOCKET-OUTLETS, VEHICLE CONNECTORS AND VEHICLE INLETS - CONDUCTIVE CHARGING OF ELECTRIC VEHICLES - PART 3: DIMENSIONAL COMPATIBILITY AND INTERCHANGEABILITY REQUIREMENTS FOR D.C. AND A.C./D.C. PIN AND CONTACT-TUBE VEHICLE COUPLERS
S.R. HD 60364-7-722:2016 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 7-722: REQUIREMENTS FOR SPECIAL INSTALLATIONS OR LOCATIONS - SUPPLIES FOR ELECTRIC VEHICLES
EN 62752:2016 In-cable control and protection device for mode 2 charging of electric road vehicles (IC-CPD)
CEI EN 62752 : 1ED 2017 IN-CABLE CONTROL AND PROTECTION DEVICE FOR MODE 2 CHARGING OF ELECTRIC ROAD VEHICLES (IC-CPD)
UNE-EN 62196-3:2014 Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 3: Dimensional compatibility and interchangeability requirements for d.c. and a.c./d.c. pin and contact-tube vehicle couplers
BS EN 62196-3:2014 Plugs, socket-outlets, vehicle connectors and vehicle inlets. Conductive charging of electric vehicles Dimensional compatibility and interchangeability requirements for d.c. and a.c./d.c. pin and contact-tube vehicle couplers
UNE-EN 62752:2017 In-cable control and protection device for mode 2 charging of electric road vehicles (IC-CPD)

EN 62196-1:2014 Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 1: General requirements
IEC 62196-1:2014 Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 1: General requirements

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Learn more on subscription solutions

or

Get in touch with us

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more