Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

EN 62246-1-1:2013

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Reed switches - Part 1-1: Generic specification - Quality assessment
Superseded date

01-04-2018

Published date

02-08-2013

FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Test schedules
5 Characteristic values of the reed switches
6 Reliability - Failure rate data
7 Marking and documentation
Annex A (normative) - Mounting in a standard coil
Annex B (normative) - Variants
Annex C (informative) - Typical applications
Bibliography
Annex ZA (normative) - Normative references to
         international publications with their
         corresponding European publications

IEC 62246-1-1:2013 is a quality assessment specification which defines requirements and tests to reed switches for use in general and industrial applications. This standard selects from IEC 62246-1:2011 and from other sources the appropriate test procedures to be used in detail specifications derived from this specification. This standard describes sampling and test schedules for qualification approval procedures, quality conformance inspection, formation of inspection lots and intervals between tests. This first edition cancels and replaces the first edition of IEC/PAS 62246-2-1 published in 2008. It is a technical revision. This edition includes the following significant technical changes with respect to the previous editions: a) inclusion of introduction; b) update of references, terms and definitions; c) renumbering of clauses to bring them into a more logical order; d) inclusion of the generic specifications for reed switches; e) update of typical applications. This publication is to be read in conjunction with IEC 62246-1:2011.

Committee
CLC/SR 94
DevelopmentNote
Redesignated as EN IEC 62246-1-1. (04/2018)
DocumentType
Standard
PublisherName
European Committee for Standards - Electrical
Status
Superseded
SupersededBy

IEC 62246-1:2015 Reed switches - Part 1: Generic specification
IEC 61373:2010 Railway applications - Rolling stock equipment - Shock and vibration tests
IEC 60068-2-27:2008 Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock
IEC 60068-2-20:2008 Environmental testing - Part 2-20: Tests - Test T: Test methods for solderability and resistance to soldering heat of devices with leads
EN 60068-2-20:2008 Environmental testing - Part 2-20: Tests - Test T: Test methods for solderability and resistance to soldering heat of devices with leads
IEC 60068-2-21:2006 Environmental testing - Part 2-21: Tests - Test U: Robustness of terminations and integral mounting devices
IEC 60068-2-13:1983 Basic environmental testing procedures - Part 2-13: Tests - Test M: Low air pressure
EN 61373:2010/AC:2017-09 RAILWAY APPLICATIONS - ROLLING STOCK EQUIPMENT - SHOCK AND VIBRATION TESTS (IEC 61373:2010)
EN 62246-1:2015 Reed switches - Part 1: Generic specification
IEC 60068-2-11:1981 Basic environmental testing procedures - Part 2-11: Tests - Test Ka: Salt mist
EN 60127-2:2014 Miniature fuses - Part 2: Cartridge fuse-links
IEC 60127-2:2014 Miniature fuses - Part 2: Cartridge fuse-links
IEC 60410:1973 Sampling plans and procedures for inspection by attributes
IEC 61810-2-1:2017 Electromechanical elementary relays - Part 2-1: Reliability - Procedure for the verification of B<sub>10</sub> values
IEC 60068-2-17:1994 Basic environmental testing procedures - Part 2-17: Tests - Test Q: Sealing
EN 60068-2-21:2006 Environmental testing - Part 2-21: Tests - Test U: Robustness of terminations and integral mounting devices
IEC 60068-2-2:2007 Environmental testing - Part 2-2: Tests - Test B: Dry heat
EN 60068-2-78:2013 Environmental testing - Part 2-78: Tests - Test Cab: Damp heat, steady state
EN 60068-2-6:2008 Environmental testing - Part 2-6: Tests - Test Fc: Vibration (sinusoidal)
EN 60068-2-11:1999 Environmental testing - Part 2: Tests - Test Ka: Salt mist
IEC 60068-2-1:2007 Environmental testing - Part 2-1: Tests - Test A: Cold
IEC 60068-2-14:2009 Environmental testing - Part 2-14: Tests - Test N: Change of temperature
EN 60068-2-14:2009 Environmental testing - Part 2-14: Tests - Test N: Change of temperature
IEC 60068-2-30:2005 Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle)

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more