Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

EN ISO 11296-3:2011

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 3: Lining with close-fit pipes (ISO 11296-3:2009+Cor 1:2011)
Superseded date

21-03-2019

Published date

11-05-2011

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Pipes at the "M" stage
6 Fittings
7 Ancillary components
8 Fitness for purpose of the installed lining system at
  the "I" stage
9 Installation practice
Annex A (normative) - Factory folded heat reverted
        polyethylene (PE) pipe - Determination of
        memory ability
Annex B (normative) - Folded polyethylene (PE) pipe -
        Determination of resistance to circumferential
        tensile stress at constant temperature
Bibliography

ISO 11296-3:2009, in conjunction with ISO 11296-1, specifies requirements and test methods for close-fit lining systems intended to be used for the renovation of non-pressure drainage and sewerage networks.It applies to pipes and fittings made of polyethylene (PE) or unplasticized poly(vinyl chloride) (PVC‑U). It is applicable to the plastic lining system only.

Committee
CEN/TC 155
DevelopmentNote
Supersedes EN 13566-3. (05/2011)
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Superseded
SupersededBy
Supersedes

PREN 15885 : DRAFT 2015 CLASSIFICATION AND CHARACTERISTICS OF TECHNIQUES FOR RENOVATION, REPAIR AND REPLACEMENT OF DRAINS AND SEWERS
16/30332542 DC : 0 BS EN 15885 - CLASSIFICATION AND CHARACTERISTICS OF TECHNIQUES FOR RENOVATION, REPAIR AND REPLACEMENT OF DRAINS AND SEWERS

ISO 13953:2001 Polyethylene (PE) pipes and fittings — Determination of the tensile strength and failure mode of test pieces from a butt-fused joint
ISO 8772:2006 Plastics piping systems for non-pressure underground drainage and sewerage Polyethylene (PE)
ISO 2507-1:1995 Thermoplastics pipes and fittings — Vicat softening temperature — Part 1: General test method
ISO 11295:2017 Classification and information on design and applications of plastics piping systems used for renovation and replacement
ISO 12176-1:2017 Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 1: Butt fusion
ISO 527-2:2012 Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics
ISO 11296-1:2009 Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks Part 1: General
ISO 6259-1:2015 Thermoplastics pipes Determination of tensile properties Part 1: General test method
ISO 3126:2005 Plastics piping systems Plastics components Determination of dimensions
ISO 18373-1:2007 Rigid PVC pipes Differential scanning calorimetry (DSC) method Part 1: Measurement of the processing temperature
ISO 4435:2003 Plastics piping systems for non-pressure underground drainage and sewerage Unplasticized poly(vinyl chloride) (PVC-U)
ISO 9967:2016 Thermoplastics pipes Determination of creep ratio
ISO 899-1:2017 Plastics — Determination of creep behaviour — Part 1: Tensile creep
ISO 21138-1:2007 Plastics piping systems for non-pressure underground drainage and sewerage Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) Part 1: Material specifications and performance criteria for pipes, fittings and system
ISO 9969:2016 Thermoplastics pipes Determination of ring stiffness
ISO 9852:2007 Unplasticized poly(vinyl chloride) (PVC-U) pipes — Dichloromethane resistance at specified temperature (DCMT) — Test method

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more