EN ISO 12215-1:2000
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
18-04-2019
01-09-2000
1 Scope
2 Normative references
3 Terms and definitions
4 Requirements for material properties of
small craft
Annex ZA (normative) Normative references to
international publications with their
relevant European publications
Sets requirements for materials and handling for small craft hull construction.
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| UNE-EN ISO 12215-1:2001 | Identical |
| UNI EN ISO 12215-1 : 2002 | Identical |
| NBN EN ISO 12215-1 : 2001 | Identical |
| I.S. EN ISO 12215-1:2000 | Identical |
| NS EN ISO 12215-1 : 1ED 2000 | Identical |
| NF EN ISO 12215-1 : 2001 | Identical |
| ISO 12215-1:2000 | Identical |
| DIN EN ISO 12215-1:2019-05 | Identical |
| DIN EN ISO 12215-1:2001-02 | Identical |
| BS EN ISO 12215-1:2018 | Identical |
| BS EN ISO 12215-1:2000 | Identical |
| ONORM EN ISO 12215-1 : 2001 | Identical |
| NEN EN ISO 12215-1 : 2000 | Identical |
| NEN EN ISO 12215-1 :2018 | Identical |
| PN-EN ISO 12215-1:2018-12 | Identical |
| ÖNORM EN ISO 12215-1: 2019 | Identical |
| SN EN ISO 12215-1 : 2001 | Identical |
| I.S. EN ISO 12215-1:2018 | Identical |
| PN EN ISO 12215-1 : 2002 | Identical |
| BS EN ISO 12215-4:2002 | Small craft. Hull construction and scantlings Workshop and manufacturing |
| ISO 12215-4:2002 | Small craft — Hull construction and scantlings — Part 4: Workshop and manufacturing |
| BS EN ISO 6185-1:2001 | Inflatable boats Boats with a maximum motor power rating of 4,5 kW |
| EN ISO 12215-4:2002 | Small craft - Hull construction and scantlings - Part 4: Workshop and manufacturing (ISO 12215-4:2002) |
| BS EN ISO 6185-2:2001 | Inflatable boats Boats with a maximum motor power rating of 4.5 kW to 15 kW inclusive |
| ISO 2811-1:2016 | Paints and varnishes — Determination of density — Part 1: Pycnometer method |
| ISO 75-1:2013 | Plastics Determination of temperature of deflection under load Part 1: General test method |
| ISO 2535:2001 | Plastics Unsaturated-polyester resins Measurement of gel time at ambient temperature |
| ISO 3521:1997 | Plastics — Unsaturated polyester and epoxy resins — Determination of overall volume shrinkage |
| ISO 527-4:1997 | Plastics Determination of tensile properties Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites |
| ISO 2884-1:1999 | Paints and varnishes — Determination of viscosity using rotary viscometers — Part 1: Cone-and-plate viscometer operated at a high rate of shear |
| EN 59:2016 | Glass reinforced plastics - Determination of indentation hardness by means of a Barcol hardness tester |
| ISO 3374:2000 | Reinforcement products Mats and fabrics Determination of mass per unit area |
| ISO 8666:2016 | Small craft Principal data |
| ISO 75-2:2013 | Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite |
| ISO 2555:1989 | Plastics Resins in the liquid state or as emulsions or dispersions Determination of apparent viscosity by the Brookfield Test method |
| ISO 2078:1993 | Textile glass Yarns Designation |
| ISO 1675:1985 | Plastics — Liquid resins — Determination of density by the pyknometer method |
| ISO 1887:2014 | Textile glass Determination of combustible-matter content |
| ISO 1889:2009 | Reinforcement yarns Determination of linear density |
| ISO 62:2008 | Plastics Determination of water absorption |
| ISO 14130:1997 | Fibre-reinforced plastic composites — Determination of apparent interlaminar shear strength by short-beam method |
| ISO 4901:2011 | Reinforced plastics based on unsaturated-polyester resins Determination of the residual styrene monomer content, as well as the content of other volatile aromatic hydrocarbons, by gas chromatography |
| DIN 16945:1989-03 | REACTION RESINS - REACTANTS AND REACTION MOULDING MATERIALS - TEST METHODS |
| ISO 178:2010 | Plastics Determination of flexural properties |
| ISO 3344:1997 | Reinforcement products — Determination of moisture content |
| ISO 527-1:2012 | Plastics Determination of tensile properties Part 1: General principles |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.