Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

EN ISO 13000-2:2005

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Plastics - Polytetrafluoroethylene (PTFE) semi-finished products - Part 2: Preparation of test specimens and determination of properties (ISO 13000-2:2005)
Superseded date

09-09-2021

Published date

15-11-2005

Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Sampling
5 Preparation of test specimens
6 Testing of semi-finished PTFE products
  6.1 General
  6.2 Linear dimensions
  6.3 Tensile properties
  6.4 Density
  6.5 Loss in mass at 300 degree C
  6.6 Dimensional stability - General method
  6.7 Dimensional stability - Special method for the
        determination of the dimensional and the
        geometrical stability of thick-walled tubes
  6.8 Electrical properties
  6.9 Hardness
  6.10 Colour
  6.11 Radiographic examination
  6.12 Resistance to environmental stress cracking (ESC)
  6.13 Deformation under load
Annex A (informative) Other standards relating to testing
        semi-finished products of PTFE

ISO 13000-2:2005 specifies the preparation of test specimens and gives the test methods applicable to semi-finished products of polytetrafluoroethylene (PTFE).

Committee
CEN/TC 249
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Superseded
SupersededBy

04/30091874 DC : DRAFT FEB 2004 BS EN ISO 13000-1 - PLASTICS - POLYTETRAFLUOROETHYLENE (PTFE) SEMI-FINISHED PRODUCTS - PART 1: REQUIREMENTS AND DESIGNATION

IEC 60243-1:2013 Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies
ASTM D 3418 : 2015 : REDLINE Standard Test Method for Transition Temperatures and Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry
ISO 12086-1:2006 Plastics Fluoropolymer dispersions and moulding and extrusion materials Part 1: Designation system and basis for specifications
IEC 60684-2:2011 Flexible insulating sleeving - Part 2: Methods of test
BS 6564-3:1990 Polytetrafluoroethylene (PTFE) materials and products Specification for E glass fibre filled polytetrafluoroethylene
IEC 60250:1969 Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including metre wavelengths
ISO 1923:1981 Cellular plastics and rubbers — Determination of linear dimensions
ISO 2039-1:2001 Plastics Determination of hardness Part 1: Ball indentation method
ASTM D 3294 : 2015 : REDLINE Standard Specification for Polytetrafluoroethylene (PTFE) Resin Molded Sheet and Molded Basic Shapes
IEC 60684-1:2003 Flexible insulating sleeving - Part 1: Definitions and general requirements
ISO 12086-2:2006 Plastics Fluoropolymer dispersions and moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties
ASTM D 3295 : 2015 : REDLINE Standard Specification for PTFE Tubing, Miniature Beading and Spiral Cut Tubing
ISO 527-2:2012 Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics
ASTM D 3369 : 2001 Standard Specification for Polytetrafluoroethylene (PTFE) Resin Cast Film (Withdrawn 2006)
ISO 472:2013 Plastics Vocabulary
ISO 13000-1:2005 Plastics Polytetrafluoroethylene (PTFE) semi-finished products Part 1: Requirements and designation
ISO 3611:2010 Geometrical product specifications (GPS) — Dimensional measuring equipment: Micrometers for external measurements — Design and metrological characteristics
ISO 4599:1986 Plastics Determination of resistance to environmental stress cracking (ESC) Bent strip method
IEC 60243-2:2013 Electric strength of insulating materials - Test methods - Part 2: Additional requirements for tests using direct voltage
IEC 60674-2:2016 Specification for plastic films for electrical purposes - Part 2: Methods of test
ISO 527-3:1995 Plastics Determination of tensile properties Part 3: Test conditions for films and sheets
ISO 4600:1992 Plastics Determination of environmental stress cracking (ESC) Ball or pin impression method
ISO 868:2003 Plastics and ebonite — Determination of indentation hardness by means of a durometer (Shore hardness)
ASTM D 4969 : 2017 : REDLINE Standard Specification for Polytetrafluoroethylene–(PTFE) Coated Glass Fabric

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more