EN ISO 15875-5:2003
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 5: Fitness for purpose of the system (ISO 15875-5:2003)
Amended by
Superseded date
08-01-2021
Published date
01-12-2003
Publisher
1 Scope
2 Normative references
3 Terms and definitions, symbols and abbreviated terms
4 Fitness for purpose of the joints and the piping system
4.1 General
4.2 Internal pressure test
4.3 Bending test
4.4 Pull-out test
4.5 Thermal cycling test
4.6 Pressure cycling test
4.7 Leaktightness under vacuum
Bibliography
ISO 15875-5:2003 specifies the characteristics of the fitness for purpose of crosslinked polyethylene (PE-X) piping systems intended to be used for hot and cold water installations, within buildings, for the conveyance of water which may or may not be intended for human consumption (domestic systems) and for heating systems, under design pressures and temperatures appropriate to the class of application.It covers a range of service conditions (classes of application) and design pressure classes. It does not apply if the values of the design temperature, maximum design temperature and malfunction temperature are in excess of those given in ISO 15875-1.It also specifies the test parameters for the test methods referred to in the standard.In conjunction with the other parts of ISO 15875, it is applicable to PE-X pipes, fittings and their joints, including joints with components of other plastics and non-plastics materials intended to be used for hot and cold water installations.
| Committee |
CEN/TC 155
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| NBN EN ISO 15875-5 : 2004 | Identical |
| PN EN ISO 15875-5 : 2005 | Identical |
| SN EN ISO 15875-5 : 2004 | Identical |
| NS EN ISO 15875-5 : 1ED 2004 | Identical |
| UNI EN ISO 15875-5 : 2007 | Identical |
| NEN EN ISO 15875-5 : 2004 | Identical |
| I.S. EN ISO 15875-5:2004 | Identical |
| BS EN ISO 15875-5:2003 | Identical |
| ISO 15875-5:2003 | Identical |
| DIN EN ISO 15875-5:2004-03 | Identical |
| NF EN ISO 15875-5 : 2004 | Identical |
| UNE-EN ISO 15875-5:2004 | Identical |
| ONORM EN ISO 15875-5 : 2004 | Identical |
| DIN EN 1254-6:2012-12 | Copper and copper alloys - Plumbing fittings - Part 6: Fittings with push-fit ends |
| 11/30197617 DC : 0 | BS ISO 11855-5 - BUILDING ENVIRONMENT DESIGN - STANDARDS FOR THE DESIGN, CONSTRUCTION AND OPERATION OF RADIANT HEATING AND COOLING SYSTEMS - PART 5: INSTALLATION |
| 07/30160794 DC : 0 | BS EN 15632-2 - DISTRICT HEATING PIPES - PRE-INSULATED FLEXIBLE PIPE SYSTEMS - PART 2: BONDED PLASTIC SERVICE PIPES - REQUIREMENTS AND TEST METHODS |
| PREN 1254-6 : DRAFT 2011 | COPPER AND COPPER ALLOYS - PLUMBING FITTINGS - PART 6: FITTING WITH PUSH-FIT ENDS |
| I.S. EN 15632-3:2010 | DISTRICT HEATING PIPES - PRE-INSULATED FLEXIBLE PIPE SYSTEMS - PART 3: NON BONDED SYSTEM WITH PLASTIC SERVICE PIPES; REQUIREMENTS AND TEST METHODS |
| DIN EN ISO 15875-3:2004-03 | Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 3: Fittings (ISO 15875-3:2003) |
| BS EN ISO 15875-3:2003 | Plastics piping systems for hot and cold water installations. Crosslinked polyethylene (PE-X) Fittings |
| BS EN ISO 15875-2:2003 | Plastics piping systems for hot and cold water installations. Crosslinked polyethylene (PE-X) Pipes |
| DIN EN 15632-2:2015-03 | District heating pipes - Pre-insulated flexible pipe systems - Part 2: Bonded plastic service pipes - Requirements and test methods (includes Amendment A1:2014) |
| 07/30160797 DC : 0 | BS EN 15632-3 - DISTRICT HEATING PIPES - PRE-INSULATED FLEXIBLE PIPE SYSTEMS - PART 3: NON BONDED PLASTIC SERVICE PIPES - REQUIREMENTS AND TEST METHODS |
| BS EN 15632-3 : 2010 | DISTRICT HEATING PIPES - PRE-INSULATED FLEXIBLE PIPE SYSTEMS - PART 3: NON BONDED SYSTEM WITH PLASTIC SERVICE PIPES; REQUIREMENTS AND TEST METHODS |
| ISO/TS 15875-7:2003 | Plastics piping systems for hot and cold water installations Crosslinked polyethylene (PE-X) Part 7: Guidance for the assessment of conformity |
| NF EN 1264-4 : 2010 | WATER BASED SURFACE EMBEDDED HEATING AND COOLING SYSTEMS - PART 4: INSTALLATION |
| DIN EN 14868:2005-11 | PROTECTION OF METALLIC MATERIALS AGAINST CORROSION - GUIDANCE ON THE ASSESSMENT OF CORROSION LIKELIHOOD IN CLOSED WATER CIRCULATION SYSTEMS |
| DIN EN 14868 E : 2005 | PROTECTION OF METALLIC MATERIALS AGAINST CORROSION - GUIDANCE ON THE ASSESSMENT OF CORROSION LIKELIHOOD IN CLOSED WATER CIRCULATION SYSTEMS |
| I.S. EN 1264-4:2009 | WATER BASED SURFACE EMBEDDED HEATING AND COOLING SYSTEMS - PART 4: INSTALLATION |
| EN ISO 15875-3:2003 | Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 3: Fittings (ISO 15875-3:2003) |
| EN ISO 15875-2:2003/A1:2007 | PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - CROSSLINKED POLYETHYLENE (PE-X) - PART 2: PIPES |
| I.S. EN ISO 15875-2:2004 | PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - CROSSLINKED POLYETHYLENE (PE-X) - PART 2: PIPES |
| I.S. EN ISO 15875-3:2004 | PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - CROSSLINKED POLYETHYLENE (PE-X) - PART 3: FITTINGS |
| 11/30213587 DC : 0 | BS EN 1254-6 - COPPER AND COPPER ALLOYS - PLUMBING FITTINGS - PART 6: FITTINGS WITH PUSH-FIT ENDS |
| 07/19990369 DC : 0 | BS EN 806-4 - SPECIFICATIONS FOR INSTALLATIONS INSIDE BUILDINGS CONVEYING WATER FOR HUMAN CONSUMPTION - PART 4 - INSTALLATION |
| BS EN 15632-2 : 2010 | DISTRICT HEATING PIPES - PRE-INSULATED FLEXIBLE PIPE SYSTEMS - PART 2: BONDED PLASTIC SERVICE PIPES - REQUIREMENTS AND TEST METHODS |
| EN 1264-4:2009 | Water based surface embedded heating and cooling systems - Part 4: Installation |
| I.S. EN 15632-2:2010 | DISTRICT HEATING PIPES - PRE-INSULATED FLEXIBLE PIPE SYSTEMS - PART 2: BONDED PLASTIC SERVICE PIPES - REQUIREMENTS AND TEST METHODS |
| CEN ISO/TS 15875-7:2003 | Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 7: Guidance for the assessment of conformity (ISO/TS 15875-7:2003) |
| DIN EN 1264-4:2009-11 | Water based surface embedded heating and cooling systems - Part 4: Installation |
| BS EN 1264-4:2009 | Water based surface embedded heating and cooling systems Installation |
| UNI EN 15015 : 2008 | PLASTICS PIPING SYSTEMS - SYSTEMS FOR HOT AND COLD WATER NOT INTENDED FOR HUMAN CONSUMPTION - PERFORMANCE CHARACTERISTICS FOR PIPES, FITTINGS AND THEIR JOINTS |
| UNI EN 1254-6 : 2012 | COPPER AND COPPER ALLOYS - PLUMBING FITTINGS - PART 6: FITTINGS WITH PUSH-FIT ENDS |
| DD CEN ISO/TS 15875-7:2003 | Plastics piping systems for hot and cold water installations. Crosslinked polyethylene (PE-X) Guidance for the assessment of conformity |
| UNI EN 1264-4 : 2009 | WATER BASED SURFACE EMBEDDED HEATING AND COOLING SYSTEMS - PART 4: INSTALLATION |
| I.S. EN 1254-6:2012 | COPPER AND COPPER ALLOYS - PLUMBING FITTINGS - PART 6: FITTINGS WITH PUSH-FIT ENDS |
| I.S. EN ISO/TS 15875-7:2004 | PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - CROSSLINKED POLYETHYLENE (PE-X) - PART 7: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY |
| BS EN 14868:2005 | Protection of metallic materials against corrosion. Guidance on the assessment of corrosion likelihood in closed water circulation systems |
| ISO 15875-3:2003 | Plastics piping systems for hot and cold water installations — Crosslinked polyethylene (PE-X) — Part 3: Fittings |
| ISO 15875-2:2003 | Plastics piping systems for hot and cold water installations — Crosslinked polyethylene (PE-X) — Part 2: Pipes |
| BS EN 806-2:2005 | Specifications for installations inside buildings conveying water for human consumption Design |
| EN 14868 : 2005 | PROTECTION OF METALLIC MATERIALS AGAINST CORROSION - GUIDANCE ON THE ASSESSMENT OF CORROSION LIKELIHOOD IN CLOSED WATER CIRCULATION SYSTEMS |
| EN 806-2:2005 | Specification for installations inside buildings conveying water for human consumption - Part 2: Design |
| EN 15632-2:2010+A1:2014 (edition 2) | District heating pipes - Pre-insulated flexible pipe systems - Part 2: Bonded plastic service pipes - Requirements and test methods |
| EN 15632-3:2010+A1:2014 (edition 2) | District heating pipes - Pre-insulated flexible pipe systems - Part 3: Non bonded system with plastic service pipes; requirements and test methods |
| BS EN 1254-6:2012 | Copper and copper alloys. Plumbing fittings Fittings with push-fit ends |
| DIN EN 15632-3:2015-03 | District heating pipes - Pre-insulated flexible pipe systems - Part 3: Non bonded system with plastic service pipes - Requirements and test methods (includes Amendment A1:2014) |
| EN 1254-6:2012 | Copper and copper alloys - Plumbing fittings - Part 6: Fittings with push-fit ends |
| UNE-EN 1254-6:2013 | Copper and copper alloys - Plumbing fittings - Part 6: Fittings with push-fit ends |
| 07/30168416 DC : 0 | BS EN 1264-4 - WATER BASED SURFACE EMBEDDED HEATING AND COOLING SYSTEMS - PART 4: INSTALLATION |
| UNI EN 806-2 : 2008 | SPECIFICATION FOR INSTALLATIONS INSIDE BUILDINGS CONVEYING WATER FOR HUMAN CONSUMPTION - PART 2: DESIGN |
| DIN EN 806-2:2005-06 | Specification for installations inside buildings conveying water for human consumption - Part 2: Design |
| UNE-EN 1264-4:2010 | Water based surface embedded heating and cooling systems - Part 4: Installation |
| EN ISO 15875-2:2003/A1:2007 | PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - CROSSLINKED POLYETHYLENE (PE-X) - PART 2: PIPES |
| EN 12293:1999 | Plastics piping systems - Thermoplastics pipes and fittings for hot and cold water - Test method for the resistance of mounted assemblies to temperature cycling |
| ISO 15875-2:2003 | Plastics piping systems for hot and cold water installations — Crosslinked polyethylene (PE-X) — Part 2: Pipes |
| EN ISO 15875-1:2003/A1:2007 | Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 1: General - Amendment 1 (ISO 15875-1:2003/Amd 1:2007) |
| EN 921:1994/AC:1995 | PLASTICS PIPING SYSTEMS - THERMOPLASTICS PIPES - DETERMINATION OF RESISTANCE TO INTERNAL PRESSURE AT CONSTANT TEMPERATURE |
| EN 713:1993 | Plastics piping systems - Mechanical joints between fittings and polyolefin pressure pipes - Test method for leaktightness under internal pressure of assemblies subjected to bending |
| ENV 12108:2001 | Plastics piping systems - Guidance for the installation inside buildings of pressure piping systems for hot and cold water intended for human consumption |
| ISO 15875-1:2003 | Plastics piping systems for hot and cold water installations — Crosslinked polyethylene (PE-X) — Part 1: General |
| EN 12295:1999 | Plastics piping systems - Thermoplastics pipes and associated fittings for hot and cold water - Test method for resistance of joints to pressure cycling |
| EN 12294:1999 | Plastics piping systems - Systems for hot and cold water - Test method for leaktightness under vacuum |
| EN 712:1993 | Thermoplastics piping systems - End-load bearing mechanical joints between pressure pipes and fittings - Test method for resistance to pull-out under constant longitudinal force |
Sorry this product is not available in your region.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.