EN ISO 15876-5:2017
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 5: Fitness for purpose of the system (ISO 15876-5:2017)
Amended by
Superseded date
08-01-2021
Published date
08-02-2017
Publisher
European foreword
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions, symbols and abbreviated terms
4 Fitness for purpose of the joints and the piping system
Bibliography
ISO 15876-5:2017 specifies the characteristics of the fitness for purpose of polybutene-1 (PB-1) piping systems, intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption, (domestic systems) and for heating systems, under design pressures and temperatures according to the class of application (see ISO 15876‑1).The designation polybutene is used together with the abbreviation PB throughout this document.ISO 15876-5:2017 covers a range of service conditions (application classes) and design pressure classes. For values of TD, Tmax and Tmal in excess of those in ISO 15876‑1:2016, Table 1, this document does not apply.NOTE It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.It also specifies the test parameters for the test methods referred to in this document.In conjunction with the other parts of ISO 15876, it is applicable to PB pipes, fittings, their joints and to joints with components of other plastics and non-plastics materials intended to be used for hot and cold water installations.
| Committee |
CEN/TC 155
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| ISO 15876-5:2017 | Identical |
| DIN EN ISO 15876-5:2017-06 | Identical |
| SS-EN ISO 15876-5:2017 | Identical |
| BS EN ISO 15876-5:2017 | Identical |
| NBN EN ISO 15876-5 : 2004 | Identical |
| UNI EN ISO 15876-5 : 2005 | Identical |
| PN EN ISO 15876-5 : 2017 | Identical |
| ONORM EN ISO 15876-5 : 2018 | Identical |
| NF EN ISO 15876-5 : 2017 | Identical |
| UNI EN ISO 15876-5:2021 | Identical |
| UNI EN ISO 15876-5:2017 | Identical |
| SN EN ISO 15876-5 : 2017 | Identical |
| DIN EN ISO 15876-5:2015-08 (Draft) | Identical |
| NEN EN ISO 15876-5 : 2017 | Identical |
| NS EN ISO 15876-5 : 2017 | Identical |
| I.S. EN ISO 15876-5:2017 | Identical |
| UNE-EN ISO 15876-5:2017 | Identical |
| DIN EN 1254-6:2012-12 | Copper and copper alloys - Plumbing fittings - Part 6: Fittings with push-fit ends |
| 07/30160794 DC : 0 | BS EN 15632-2 - DISTRICT HEATING PIPES - PRE-INSULATED FLEXIBLE PIPE SYSTEMS - PART 2: BONDED PLASTIC SERVICE PIPES - REQUIREMENTS AND TEST METHODS |
| PREN 1254-6 : DRAFT 2011 | COPPER AND COPPER ALLOYS - PLUMBING FITTINGS - PART 6: FITTING WITH PUSH-FIT ENDS |
| I.S. EN 15632-3:2010 | DISTRICT HEATING PIPES - PRE-INSULATED FLEXIBLE PIPE SYSTEMS - PART 3: NON BONDED SYSTEM WITH PLASTIC SERVICE PIPES; REQUIREMENTS AND TEST METHODS |
| DIN EN 15632-2:2015-03 | District heating pipes - Pre-insulated flexible pipe systems - Part 2: Bonded plastic service pipes - Requirements and test methods (includes Amendment A1:2014) |
| 07/30160797 DC : 0 | BS EN 15632-3 - DISTRICT HEATING PIPES - PRE-INSULATED FLEXIBLE PIPE SYSTEMS - PART 3: NON BONDED PLASTIC SERVICE PIPES - REQUIREMENTS AND TEST METHODS |
| 11/30197617 DC : 0 | BS ISO 11855-5 - BUILDING ENVIRONMENT DESIGN - STANDARDS FOR THE DESIGN, CONSTRUCTION AND OPERATION OF RADIANT HEATING AND COOLING SYSTEMS - PART 5: INSTALLATION |
| BS EN 15632-3 : 2010 | DISTRICT HEATING PIPES - PRE-INSULATED FLEXIBLE PIPE SYSTEMS - PART 3: NON BONDED SYSTEM WITH PLASTIC SERVICE PIPES; REQUIREMENTS AND TEST METHODS |
| NF EN 1264-4 : 2010 | WATER BASED SURFACE EMBEDDED HEATING AND COOLING SYSTEMS - PART 4: INSTALLATION |
| DIN EN 14868:2005-11 | PROTECTION OF METALLIC MATERIALS AGAINST CORROSION - GUIDANCE ON THE ASSESSMENT OF CORROSION LIKELIHOOD IN CLOSED WATER CIRCULATION SYSTEMS |
| DIN EN 14868 E : 2005 | PROTECTION OF METALLIC MATERIALS AGAINST CORROSION - GUIDANCE ON THE ASSESSMENT OF CORROSION LIKELIHOOD IN CLOSED WATER CIRCULATION SYSTEMS |
| DIN EN ISO 15876-2:2004-03 | PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - POLYBUTYLENE (PB) - PART 2: PIPES |
| I.S. EN 1264-4:2009 | WATER BASED SURFACE EMBEDDED HEATING AND COOLING SYSTEMS - PART 4: INSTALLATION |
| I.S. EN ISO/TS 15876-7:2004 | PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - POLYBUTYLENE (PB) - PART 7: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY |
| 11/30213587 DC : 0 | BS EN 1254-6 - COPPER AND COPPER ALLOYS - PLUMBING FITTINGS - PART 6: FITTINGS WITH PUSH-FIT ENDS |
| 07/19990369 DC : 0 | BS EN 806-4 - SPECIFICATIONS FOR INSTALLATIONS INSIDE BUILDINGS CONVEYING WATER FOR HUMAN CONSUMPTION - PART 4 - INSTALLATION |
| BS EN 15632-2 : 2010 | DISTRICT HEATING PIPES - PRE-INSULATED FLEXIBLE PIPE SYSTEMS - PART 2: BONDED PLASTIC SERVICE PIPES - REQUIREMENTS AND TEST METHODS |
| EN ISO/TS 15876-7 : 2003 | PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - POLYBUTYLENE (PB) - PART 7: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY |
| EN 1264-4:2009 | Water based surface embedded heating and cooling systems - Part 4: Installation |
| I.S. EN 15632-2:2010 | DISTRICT HEATING PIPES - PRE-INSULATED FLEXIBLE PIPE SYSTEMS - PART 2: BONDED PLASTIC SERVICE PIPES - REQUIREMENTS AND TEST METHODS |
| ISO/TS 15876-7:2003 | Plastics piping systems for hot and cold water installations Polybutylene (PB) Part 7: Guidance for the assessment of conformity |
| DIN EN 1264-4:2009-11 | Water based surface embedded heating and cooling systems - Part 4: Installation |
| BS EN 1264-4:2009 | Water based surface embedded heating and cooling systems Installation |
| UNI EN 15015 : 2008 | PLASTICS PIPING SYSTEMS - SYSTEMS FOR HOT AND COLD WATER NOT INTENDED FOR HUMAN CONSUMPTION - PERFORMANCE CHARACTERISTICS FOR PIPES, FITTINGS AND THEIR JOINTS |
| UNI EN 1254-6 : 2012 | COPPER AND COPPER ALLOYS - PLUMBING FITTINGS - PART 6: FITTINGS WITH PUSH-FIT ENDS |
| UNI EN 1264-4 : 2009 | WATER BASED SURFACE EMBEDDED HEATING AND COOLING SYSTEMS - PART 4: INSTALLATION |
| I.S. EN 1254-6:2012 | COPPER AND COPPER ALLOYS - PLUMBING FITTINGS - PART 6: FITTINGS WITH PUSH-FIT ENDS |
| BS EN 14868:2005 | Protection of metallic materials against corrosion. Guidance on the assessment of corrosion likelihood in closed water circulation systems |
| BS EN 806-2:2005 | Specifications for installations inside buildings conveying water for human consumption Design |
| EN 14868 : 2005 | PROTECTION OF METALLIC MATERIALS AGAINST CORROSION - GUIDANCE ON THE ASSESSMENT OF CORROSION LIKELIHOOD IN CLOSED WATER CIRCULATION SYSTEMS |
| EN 806-2:2005 | Specification for installations inside buildings conveying water for human consumption - Part 2: Design |
| EN 15632-2:2010+A1:2014 (edition 2) | District heating pipes - Pre-insulated flexible pipe systems - Part 2: Bonded plastic service pipes - Requirements and test methods |
| EN 15632-3:2010+A1:2014 (edition 2) | District heating pipes - Pre-insulated flexible pipe systems - Part 3: Non bonded system with plastic service pipes; requirements and test methods |
| BS EN 1254-6:2012 | Copper and copper alloys. Plumbing fittings Fittings with push-fit ends |
| DIN EN 15632-3:2015-03 | District heating pipes - Pre-insulated flexible pipe systems - Part 3: Non bonded system with plastic service pipes - Requirements and test methods (includes Amendment A1:2014) |
| EN 1254-6:2012 | Copper and copper alloys - Plumbing fittings - Part 6: Fittings with push-fit ends |
| UNE-EN 1254-6:2013 | Copper and copper alloys - Plumbing fittings - Part 6: Fittings with push-fit ends |
| 07/30168416 DC : 0 | BS EN 1264-4 - WATER BASED SURFACE EMBEDDED HEATING AND COOLING SYSTEMS - PART 4: INSTALLATION |
| UNI EN 806-2 : 2008 | SPECIFICATION FOR INSTALLATIONS INSIDE BUILDINGS CONVEYING WATER FOR HUMAN CONSUMPTION - PART 2: DESIGN |
| DD CEN ISO/TS 15876-7:2003 | Plastics piping systems for hot and cold water installations. Polybutylene (PB) Guidance for the assessment of conformity |
| DIN EN 806-2:2005-06 | Specification for installations inside buildings conveying water for human consumption - Part 2: Design |
| UNE-EN 1264-4:2010 | Water based surface embedded heating and cooling systems - Part 4: Installation |
| ISO 19892:2011 | Plastics piping systems Thermoplastics pipes and fittings for hot and cold water Test method for the resistance of joints to pressure cycling |
| ISO 1167-2:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces |
| ISO 13056:2011 | Plastics piping systems Pressure systems for hot and cold water Test method for leaktightness under vacuum |
| ISO 1167-4:2007 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 4: Preparation of assemblies |
| ISO 3501:2015 | Plastics piping systems Mechanical joints between fittings and pressure pipes Test method for resistance to pull-out under constant longitudinal force |
| ISO 19893:2011 | Plastics piping systems Thermoplastics pipes and fittings for hot and cold water Test method for the resistance of mounted assemblies to temperature cycling |
| ISO/TS 15876-7:2003 | Plastics piping systems for hot and cold water installations Polybutylene (PB) Part 7: Guidance for the assessment of conformity |
| ISO 15876-1:2017 | Plastics piping systems for hot and cold water installations — Polybutene (PB) — Part 1: General |
| ISO 15876-3:2017 | Plastics piping systems for hot and cold water installations — Polybutene (PB) — Part 3: Fittings |
| ISO 1167-3:2007 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 3: Preparation of components |
| CEN/TR 12108:2012 | Plastics piping systems - Guidance for the installation inside buildings of pressure piping systems for hot and cold water intended for human consumption |
| ISO 15876-2:2017 | Plastics piping systems for hot and cold water installations — Polybutene (PB) — Part 2: Pipes |
| ISO 3503:2015 | Plastics piping systems Mechanical joints between fittings and pressure pipes Test method for leaktightness under internal pressure of assemblies subjected to bending |
| ISO 1167-1:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method |
Sorry this product is not available in your region.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.