EN ISO 16000-10:2006
Current
The latest, up-to-date edition.
Indoor air - Part 10: Determination of the emission of volatile organic compounds from building products and furnishing - Emission test cell method (ISO 16000-10:2006)
01-02-2006
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Principle
6 Emission test cell system
7 Apparatus
8 Test conditions
9 Verification of the test conditions
10 Test specimens
11 Emission test cell preparation
12 Test method
13 Calculation of area specific emission rates and
expression of results
14 Performance characteristics
15 Test report
Annex A (normative) - System for quality assurance/quality
control
Annex B (informative) - Examples of area specific air flow
rates in a model room
Annex C (informative) - Example of an emission test cell
Bibliography
ISO 16000-10:2006 specifies a general laboratory test method for determination of the area specific emission rate of volatile organic compounds (VOCs) from newly produced building products or furnishing under defined climate conditions. The method can also, in principle, be applied to aged products. The emission data obtained can be used to calculate concentrations in a model room. According to the definition of an emission test cell, it is also possible to perform non-destructive emission measurements on building products on-site in buildings. However, the procedure for such measurements is not described in ISO 16000-10:2006. An example of an emission test cell is described.ISO 16000-10:2006 is also applicable to wood-based panels and other building products, in order to determine the emission rate of formaldehyde.
| Committee |
CEN/TC 264
|
| DevelopmentNote |
Supersedes ENV 13419-2. (03/2006)
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Current
|
| Standards | Relationship |
| SN EN ISO 16000-10 : 2006 | Identical |
| NS EN ISO 16000-10 : 1ED 2006 | Identical |
| ISO 16000-10:2006 | Identical |
| DIN EN ISO 16000-10:2006-06 | Identical |
| BS EN ISO 16000-10:2006 | Identical |
| PN EN ISO 16000-10 : 2010 | Identical |
| NBN EN ISO 16000-10 : 2006 | Identical |
| UNI EN ISO 16000-10 : 2006 | Identical |
| NF EN ISO 16000-10 : 2006 | Identical |
| NEN EN ISO 16000-10 : 2006 | Identical |
| I.S. EN ISO 16000-10:2006 | Identical |
| UNE-EN ISO 16000-10:2006 | Identical |
| SS-EN ISO 16000-10 : 2006 | Identical |
| PD CEN/TR 16496:2013 | Construction Products. Assessment of release of dangerous substances. Use of harmonised horizontal assessment methods |
| DIN EN 16402 E : 2014 | PAINTS AND VARNISHES - ASSESSMENT OF EMISSIONS OF SUBSTANCES FROM COATINGS INTO INDOOR AIR - SAMPLING, CONDITIONING AND TESTING |
| PD CEN/TS 16516:2013 | Construction products. Assessment of release of dangerous substances. Determination of emissions into indoor air |
| BS EN 16687:2015 | Construction products. Assessment of release of dangerous substances. Terminology |
| S.R. CEN/TR 16098:2010 | CONSTRUCTION PRODUCTS: ASSESSMENT OF RELEASE OF DANGEROUS SUBSTANCES - CONCEPT OF HORIZONTAL TESTING PROCEDURES IN SUPPORT OF REQUIREMENTS UNDER THE CPD |
| UNE-EN 16402:2014 | Paints and varnishes - Assessment of emissions of substances from coatings into indoor air - Sampling, conditioning and testing |
| 17/30362165 DC : 0 | BS EN 16402 - PAINTS AND VARNISHES - ASSESSMENT OF EMISSIONS OF SUBSTANCES FROM COATINGS INTO INDOOR AIR - SAMPLING, CONDITIONING AND TESTING |
| DIN EN 13999-1:2014-03 | ADHESIVES - SHORT TERM METHOD FOR MEASURING THE EMISSION PROPERTIES OF LOW-SOLVENT OR SOLVENT-FREE ADHESIVES AFTER APPLICATION - PART 1: GENERAL PROCEDURE |
| UNE-EN 13999-1:2014 | Adhesives - Short term method for measuring the emission properties of low-solvent or solvent-free adhesives after application - Part 1: General procedure |
| UNI EN 16402 : 2013 | PAINTS AND VARNISHES - ASSESSMENT OF EMISSIONS OF SUBSTANCES FROM COATINGS INTO INDOOR AIR - SAMPLING, CONDITIONING AND TESTING |
| I.S. EN 13999-1:2013 | ADHESIVES - SHORT TERM METHOD FOR MEASURING THE EMISSION PROPERTIES OF LOW-SOLVENT OR SOLVENT-FREE ADHESIVES AFTER APPLICATION - PART 1: GENERAL PROCEDURE |
| VDI 2055 Blatt 2:2013-10 | Thermal insulation of heated and refrigerated operational installations in the industry and in the building services - Technical basics for the verification of properties of insulating materials |
| I.S. EN 16402:2013 | PAINTS AND VARNISHES - ASSESSMENT OF EMISSIONS OF SUBSTANCES FROM COATINGS INTO INDOOR AIR - SAMPLING, CONDITIONING AND TESTING |
| UNE-EN 16687:2016 | Construction products - Assessment of release of dangerous substances - Terminology |
| PD CEN/TR 16098:2010 | Construction products. Assessment of release of dangerous substances. Concept of horizontal testing procedures in support of requirements under the CPD |
| BS EN 16402:2013 | Paints and varnishes. Assessment of emissions of substances from coatings into indoor air. Sampling, conditioning and testing |
| EN 16402:2013 | Paints and varnishes - Assessment of emissions of substances from coatings into indoor air - Sampling, conditioning and testing |
| UNI EN 13999-1 : 2014 | ADHESIVES - SHORT TERM METHOD FOR MEASURING THE EMISSION PROPERTIES OF LOW-SOLVENT OR SOLVENT-FREE ADHESIVES AFTER APPLICATION - PART 1: GENERAL PROCEDURE |
| EN 13999-1:2013 | Adhesives - Short term method for measuring the emission properties of low-solvent or solvent-free adhesives after application - Part 1: General procedure |
| 12/30259194 DC : 0 | BS EN 13999-1 - ADHESIVES - SHORT TERM METHOD FOR MEASURING THE EMISSION PROPERTIES OF LOW-SOLVENT OR SOLVENT-FREE ADHESIVES AFTER APPLICATION - PART 1: GENERAL PROCEDURE |
| PREN 13999-1 : DRAFT 2012 | ADHESIVES - SHORT TERM METHOD FOR MEASURING THE EMISSION PROPERTIES OF LOW-SOLVENT OR SOLVENT-FREE ADHESIVES AFTER APPLICATION - PART 1: GENERAL PROCEDURE |
| 15/30322088 DC : 0 | BS EN 16516 - CONSTRUCTION PRODUCTS - ASSESSMENT OF RELEASE OF DANGEROUS SUBSTANCES - DETERMINATION OF EMISSIONS INTO INDOOR AIR |
| S.R. CEN/TS 16516:2013 | CONSTRUCTION PRODUCTS - ASSESSMENT OF RELEASE OF DANGEROUS SUBSTANCES - DETERMINATION OF EMISSIONS INTO INDOOR AIR |
| S.R. CEN/TR 16496:2013 | CONSTRUCTION PRODUCTS - ASSESSMENT OF RELEASE OF DANGEROUS SUBSTANCES - USE OF HARMONISED HORIZONTAL ASSESSMENT METHODS |
| UNI CEN/TS 16516 : 2013 | CONSTRUCTION PRODUCTS - ASSESSMENT OF RELEASE OF DANGEROUS SUBSTANCES - DETERMINATION OF EMISSIONS INTO INDOOR AIR |
| EN 16687:2015 | Construction products - Assessment of release of dangerous substances - Terminology |
| I.S. EN 16687:2015 | CONSTRUCTION PRODUCTS - ASSESSMENT OF RELEASE OF DANGEROUS SUBSTANCES - TERMINOLOGY |
| 13/30292989 DC : 0 | BS EN 16687 - CONSTRUCTION PRODUCTS - ASSESSMENT OF RELEASE OF DANGEROUS SUBSTANCES - TERMINOLOGY |
| BS EN 13999-1:2013 | Adhesives. Short term method for measuring the emission properties of low-solvent or solvent-free adhesives after application General procedure |
| CEN/TR 16098:2010 | Construction products: Assessment of release of dangerous substances - Concept of horizontal testing procedures in support of requirements under the CPD |
| CEN/TS 16516:2013 | Construction products - Assessment of release of dangerous substances - Determination of emissions into indoor air |
| CEN/TR 16496:2013 | Construction Products - Assessment of release of dangerous substances - Use of harmonised horizontal assessment methods |
| DIN EN 16402:2014-02 | PAINTS AND VARNISHES - ASSESSMENT OF EMISSIONS OF SUBSTANCES FROM COATINGS INTO INDOOR AIR - SAMPLING, CONDITIONING AND TESTING |
| EN 717-1:2004 | Wood-based panels - Determination of formaldehyde release - Part 1: Formaldehyde emission by the chamber method |
| ISO 16017-1:2000 | Indoor, ambient and workplace air — Sampling and analysis of volatile organic compounds by sorbent tube/thermal desorption/capillary gas chromatography — Part 1: Pumped sampling |
| ISO 1302:2002 | Geometrical Product Specifications (GPS) Indication of surface texture in technical product documentation |
| ISO 16000-3:2011 | Indoor air — Part 3: Determination of formaldehyde and other carbonyl compounds in indoor air and test chamber air — Active sampling method |
| ISO 12460-1:2007 | Wood-based panels Determination of formaldehyde release Part 1: Formaldehyde emission by the 1-cubic-metre chamber method |
| ISO 554:1976 | Standard atmospheres for conditioning and/or testing — Specifications |
| ISO 16000-11:2006 | Indoor air — Part 11: Determination of the emission of volatile organic compounds from building products and furnishing — Sampling, storage of samples and preparation of test specimens |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.