EN ISO 16810:2014
Current
Current
The latest, up-to-date edition.
Non-destructive testing - Ultrasonic testing - General principles (ISO 16810:2012)
Published date
05-03-2014
Publisher
Foreword
Introduction
1 Scope
2 Normative references
3 Qualification and certification
of personnel
4 Information required prior
to examination
5 Principles of ultrasonic examination
6 Equipment
7 Settings
8 Preparation for examination
9 Examination
10 Characterization of imperfections
11 Examination procedure
12 Examination report
ISO 16810:2012 defines the general principles required for the ultrasonic examination of industrial products that permit the transmission of ultrasound.The specific conditions of application and use of ultrasonic examination, which depend on the type of product examined, are described in documents which could include: a) product standards; b) specifications; c) codes; d) contractual documents; e) written procedures.Unless otherwise specified in the referencing documents the minimum requirements of ISO 16810:2012 are applicable. ISO 16810:2012 does not define: 1) extent of examination and scanning plans; 2) acceptance criteria.
| Committee |
CEN/TC 138
|
| DevelopmentNote |
Supersedes EN 583-1. (03/2014)
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Current
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| UNE-EN ISO 16810:2014 | Identical |
| ISO 16810:2012 | Identical |
| NF EN ISO 16810 : 2014 | Identical |
| NBN EN ISO 16810 : 2014 | Identical |
| NEN EN ISO 16810 : 2014 | Identical |
| NS EN ISO 16810 : 2014 | Identical |
| I.S. EN ISO 16810:2014 | Identical |
| PN EN ISO 16810 : 2014 | Identical |
| SN EN ISO 16810 : 2014 | Identical |
| UNI EN ISO 16810 : 2014 | Identical |
| SS-EN ISO 16810:2014 | Identical |
| BS EN ISO 16810:2014 | Identical |
| DIN EN ISO 16810:2014-07 | Identical |
| DIN EN ISO 16810 E : 2014 | Identical |
| DIN EN 16125:2016-03 | LPG EQUIPMENT AND ACCESSORIES - PIPEWORK SYSTEMS AND SUPPORTS - LPG LIQUID PHASE AND VAPOUR PRESSURE PHASE |
| I.S. EN 448:2015 | DISTRICT HEATING PIPES - PREINSULATED BONDED PIPE SYSTEMS FOR DIRECTLY BURIED HOT WATER NETWORKS - FITTING ASSEMBLIES OF STEEL SERVICE PIPES, POLYURETHANE THERMAL INSULATION AND OUTER CASING OF POLYETHYLENE |
| BS EN 13480-8:2017 | Metallic industrial piping Additional requirements for aluminium and aluminium alloy piping |
| BS EN 13480-8:2017+A1:2019 | Metallic industrial piping Additional requirements for aluminium and aluminium alloy piping |
| I.S. EN 10213:2007 | STEEL CASTINGS FOR PRESSURE PURPOSES |
| I.S. EN 16125:2015 | LPG EQUIPMENT AND ACCESSORIES - PIPEWORK SYSTEMS AND SUPPORTS - LPG IN LIQUID PHASE AND VAPOUR PRESSURE PHASE |
| UNE-EN 16668:2016 | Industrial valves - Requirements and testing for metallic valves as pressure accessories |
| I.S. EN 16668:2016 | INDUSTRIAL VALVES - REQUIREMENTS AND TESTING FOR METALLIC VALVES AS PRESSURE ACCESSORIES |
| PREN 448 : DRAFT 2018 | DISTRICT HEATING PIPES - PREINSULATED BONDED PIPE SYSTEMS FOR DIRECTLY BURIED HOT WATER NETWORKS - FITTING ASSEMBLIES OF STEEL SERVICE PIPES, POLYURETHANE THERMAL INSULATION AND OUTER CASING OF POLYETHYLENE |
| DIN EN 1559-2:2014-12 | FOUNDING - TECHNICAL CONDITIONS OF DELIVERY - PART 2: ADDITIONAL REQUIREMENTS FOR STEEL CASTINGS |
| I.S. EN 1559-2:2014 | FOUNDING - TECHNICAL CONDITIONS OF DELIVERY - PART 2 - ADDITIONAL REQUIREMENTS FOR STEEL CASTINGS |
| I.S. EN 13480-8:2017&LC:2019 | METALLIC INDUSTRIAL PIPING - PART 8: ADDITIONAL REQUIREMENTS FOR ALUMINIUM AND ALUMINIUM ALLOY PIPING |
| PREN 12799 : DRAFT 2017 | BRAZING - NON-DESTRUCTIVE EXAMINATION OF BRAZED JOINTS |
| 16/30342040 DC : 0 | BS EN 13941-2 - DISTRICT HEATING PIPES - DESIGN AND INSTALLATION OF THERMAL INSULATED BONDED SINGLE AND TWIN PIPE SYSTEMS FOR DIRECTLY BURIED HOT WATER NETWORKS - PART 2: INSTALLATION |
| BS EN 16125:2015 | LPG Equipment and Accessories. Pipework systems and supports. LPG in liquid phase and vapour pressure phase |
| BS EN 16668 : 2016 | INDUSTRIAL VALVES - REQUIREMENTS AND TESTING FOR METALLIC VALVES AS PRESSURE ACCESSORIES |
| DIN EN 448:2016-02 | DISTRICT HEATING PIPES - PREINSULATED BONDED PIPE SYSTEMS FOR DIRECTLY BURIED HOT WATER NETWORKS - FITTING ASSEMBLIES OF STEEL SERVICE PIPES, POLYURETHANE THERMAL INSULATION AND OUTER CASING OF POLYETHYLENE |
| UNE-EN 16125:2016 | LPG Equipment and Accessories - Pipework systems and supports - LPG in liquid phase and vapour pressure phase |
| EN 1559-2:2014 | Founding - Technical conditions of delivery - Part 2: Additional requirements for steel castings |
| UNI EN 1559-2 : 2014 | FOUNDING - TECHNICAL CONDITIONS OF DELIVERY - PART 2: ADDITIONAL REQUIREMENTS FOR STEEL CASTINGS |
| UNE-EN 13480-8:2017 | Metallic industrial piping - Part 8: Additional requirements for aluminium and aluminium alloy piping (Endorsed by Asociación Española de Normalización in September of 2019.) |
| UNE-EN 10213:2009 | Steel castings for pressure purposes |
| BS EN 1559-2:2014 | Founding. Technical conditions of delivery Additional requirements for steel castings |
| UNE-EN 448:2017 | District heating pipes - Preinsulated bonded pipe systems for directly buried hot water networks - Fitting assemblies of steel service pipes, polyurethane thermal insulation and outer casing of polyethylene |
| EN 16668:2016+A1:2018 | Industrial valves - Requirements and testing for metallic valves as pressure accessories |
| EN 16125:2015 | LPG Equipment and Accessories - Pipework systems and supports - LPG in liquid phase and vapour pressure phase |
| EN 448:2015 | District heating pipes - Preinsulated bonded pipe systems for directly buried hot water networks - Fitting assemblies of steel service pipes, polyurethane thermal insulation and outer casing of polyethylene |
| EN 13480-8:2017 | Metallic industrial piping - Part 8: Additional requirements for aluminium and aluminium alloy piping |
| 15/30317351 DC : 0 | BS EN 13480-8:2012/A2 - METALLIC INDUSTRIAL PIPING - PART 8: ADDITIONAL REQUIREMENTS FOR ALUMINIUM AND ALUMINIUM ALLOY PIPING |
| 18/30368651 DC : 0 | BS EN 448 - DISTRICT HEATING PIPES - BONDED SINGLE PIPE SYSTEMS FOR DIRECTLY BURIED HOT WATER NETWORKS - FACTORY MADE FITTING ASSEMBLIES OF STEEL SERVICE PIPES, POLYURETHANE THERMAL INSULATION AND A CASING OF POLYETHYLENE |
| 17/30359544 DC : 0 | BS EN 12799 - BRAZING - NON-DESTRUCTIVE EXAMINATION OF BRAZED JOINTS |
| BS EN 448:2015 | District heating pipes. Preinsulated bonded pipe systems for directly buried hot water networks. Fitting assemblies of steel service pipes, polyurethane thermal insulation and outer casing of polyethylene |
| DIN EN 10213:2016-10 | STEEL CASTINGS FOR PRESSURE PURPOSES |
| BS EN 10213 : 2007 | STEEL CASTINGS FOR PRESSURE PURPOSES |
| EN 10213:2007+A1:2016 | Steel castings for pressure purposes |
| UNE-EN 16125:2020 | LPG Equipment and Accessories - Pipework systems and supports - LPG in liquid phase and vapour pressure phase |
| ISO 16823:2012 | Non-destructive testing — Ultrasonic testing — Transmission technique |
| EN 12668-2:2010 | Non-destructive testing - Characterization and verification of ultrasonic examination equipment - Part 2: Probes |
| ISO 2400:2012 | Non-destructive testing — Ultrasonic testing — Specification for calibration block No. 1 |
| ISO 9712:2012 | Non-destructive testing Qualification and certification of NDT personnel |
| EN 12668-1:2010 | Non-destructive testing - Characterization and verification of ultrasonic examination equipment - Part 1: Instruments |
| ISO 16811:2012 | Non-destructive testing — Ultrasonic testing — Sensitivity and range setting |
| EN 12668-3:2013 | Non-destructive testing - Characterization and verification of ultrasonic examination equipment - Part 3: Combined equipment |
| ISO 7963:2006 | Non-destructive testing — Ultrasonic testing —- Specification for calibration block No. 2 |
Sorry this product is not available in your region.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.