EN ISO 178:2010/A1:2013
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES (ISO 178:2010/AMD 1:2013)
Superseded date
22-01-2020
Published date
12-01-2013
Publisher
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Principle
5 Test machine
6 Test specimens
7 Atmosphere for conditioning and testing
8 Procedure
9 Calculation and expression of results
10 Precision
11 Test report
Annex A (informative) - Precision statement
Annex B (informative) - Influence of changes in test
speed on the measured values of flexural
properties
Bibliography
Defines a method for determining the flexural properties of rigid and semi-rigid plastics under defined conditions.
| Committee |
TC 249
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| NS EN ISO 178 : 2010 AMD 1 2013 | Identical |
| ISO 178:2010 | Identical |
| SN EN ISO 178 : 2011 AMD 1 2013 | Identical |
| NF EN ISO 178 : 2011 AMD 1 2013 | Identical |
| BS EN ISO 178 : 2010 | Identical |
| DIN EN ISO 178 E : 2013 | Identical |
| ONORM EN ISO 178 : 2013 | Identical |
| NBN EN ISO 178 : 2011 AMD 1 2013 | Identical |
| PN EN ISO 178 : 2011 AMD 1 2013 | Identical |
| NEN EN ISO 178 : 2010 AMD 1 2013 | Identical |
| UNI EN ISO 178 : 2013 | Identical |
| BS EN ISO 178:2019 | Identical |
| I.S. EN ISO 178:2010 | Identical |
| I.S. EN ISO 178:2019 | Identical |
| ISO 178:2019 | Identical |
| UNE-EN ISO 178:2011/A1:2013 | Identical |
| BS EN ISO 178:2010+A1:2013 | Identical |
| I.S. EN ISO 178:2010+A1:2013 | Identical |
| DIN EN ISO 178:2013-09 | Identical |
| CEI EN 60371-2 : 2005 | SPECIFICATION FOR INSULATING MATERIALS BASED ON MICA - PART 2: METHODS OF TEST |
| BS EN 15564:2008 | Precast concrete products. Resin bound concrete. Requirements and test methods |
| 02/103631 DC : DRAFT MAY 2002 | BS EN 14471 - CHIMNEYS - REQUIREMENTS AND TEST METHODS FOR SYSTEM CHIMNEYS WITH PLASTIC FLUE LINERS |
| 14/30303794 DC : 0 | BS EN 438-2 - HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 2: DETERMINATION OF PROPERTIES |
| PREN 438-2 : DRAFT 2014 | HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 2: DETERMINATION OF PROPERTIES |
| 07/30172710 DC : 0 | BS EN 438-8 - HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 8: CLASSIFICATION AND SPECIFICATIONS FOR DESIGN LAMINATES |
| 10/30228056 DC : 0 | |
| 17/30357440 DC : DRAFT SEP 2017 | BS EN 438-8 - HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 8: CLASSIFICATION AND SPECIFICATIONS FOR DESIGN LAMINATES |
| 02/121749 DC : DRAFT APR 2002 | PREN 438-4 - HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 4: CLASSIFICATION AND SPECIFICATIONS FOR COMPACT LAMINATES OF THICKNESS 2 MM AND GREATER |
| 16/30329416 DC : 0 | BS EN 12566-3 - SMALL WASTEWATER TREATMENT SYSTEMS UP TO 50 PT - PART 3: PACKAGED AND/OR SITE ASSEMBLED DOMESTIC WASTEWATER TREATMENT PLANTS |
| I.S. CEN TS 1852-3:2003 | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - POLYPROPYLENE (PP) - PART 3: GUIDANCE FOR INSTALLATION |
| 13/30290552 DC : 0 | BS EN 4691-1 AEROSPACE SERIES - TIE ROD WITH INTEGRATED BOLTS - PART 1: TECHNICAL SPECIFICATION |
| BS EN 4702-05:2017 | Aerospace series. Quick release fastening systems for non-structural and lining applications Retaining washer |
| I.S. EN 60079-0:2012 | EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS (IEC 60079-0:2011 (MOD)) |
| CEI EN 50342-5 : 2012 | LEAD-ACID STARTER BATTERIES - PART 5: PROPERTIES OF BATTERY HOUSINGS AND HANDLES |
| PREN 845-1 : DRAFT 2012 | SPECIFICATION FOR ANCILLARY COMPONENTS FOR MASONRY - PART 1: WALL TIES, TENSION STRAPS, HANGERS AND BRACKETS |
| DIN EN 15345:2008-02 | Plastics - Recycled Plastics - Characterisation of Polypropylene (PP) recyclates |
| DIN EN 14963 E : 2006 | ROOF COVERINGS - CONTINUOUS ROOFLIGHTS OF PLASTICS WITH OR WITHOUT UPSTANDS - CLASSIFICATION, REQUIREMENTS AND TEST METHODS |
| DIN EN 13245-3 E : 2010 | PLASTICS - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) PROFILES FOR BUILDING APPLICATIONS - PART 3: DESIGNATION OF PVC-UE PROFILES |
| 13/30291069 DC : 0 | BS EN 12608-1 - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) PROFILES FOR THE FABRICATION OF WINDOWS AND DOORS - CLASSIFICATION, REQUIREMENTS AND TEST METHODS - PART 1: NON-COATED PVC-U PROFILES WITH LIGHT COLOURED SURFACES |
| 16/30337086 DC : DRAFT APR 2016 | BS EN 1504-4 - PRODUCTS AND SYSTEMS FOR THE PROTECTION AND REPAIR OF CONCRETE - DEFINITIONS, REQUIREMENTS, QUALITY CONTROL AND EVALUATION OF CONFORMITY - PART 4: STRUCTURAL BONDING |
| BS EN 60216-2:2005 | Electrical insulating materials. Thermal endurance properties Determination of thermal endurance properties of electrical insulating materials. Choice of test criteria |
| UNI EN 16240 : 2014 | LIGHT TRANSMITTING FLAT SOLID POLYCARBONATE (PC) SHEETS FOR INTERNAL AND EXTERNAL USE IN ROOFS, WALLS AND CEILINGS - REQUIREMENTS AND TEST METHODS |
| CEI EN 60544-2 : 2013 | ELECTRICAL INSULATING MATERIALS - DETERMINATION OF THE EFFECTS OF IONIZING RADIATION ON INSULATING MATERIALS - PART 2: PROCEDURES FOR IRRADIATION AND TEST |
| I.S. EN 4702-05:2017 | AEROSPACE SERIES - QUICK RELEASE FASTENING SYSTEMS FOR NON-STRUCTURAL AND LINING APPLICATIONS - PART 05: RETAINING WASHER |
| PREN 50342-5 : DRAFT 2010 | LEAD-ACID STARTER BATTERIES - PART 5: PROPERTIES OF BATTERY HOUSINGS AND HANDLES |
| EN 61439-1:2011 | Low-voltage switchgear and controlgear assemblies - Part 1: General rules |
| PREN 13160-7 : DRAFT 2014 | LEAK DETECTION SYSTEMS - PART 7: REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR INTERSTITIAL SPACES, LEAK DETECTION LININGS AND LEAK DETECTION JACKETS |
| PREN 4702-05 : DRAFT 2016 | AEROSPACE SERIES - QUICK RELEASE FASTENING SYSTEMS WITH NON METALLIC STUD FOR NON-STRUCTURAL APPLICATIONS - PART 05: RETAINING WASHER |
| I.S. EN 62109-1:2010 | SAFETY OF POWER CONVERTERS FOR USE IN PHOTOVOLTAIC POWER SYSTEMS - PART 1: GENERAL REQUIREMENTS |
| BS EN ISO 12215-1:2000 | Small craft. Hull construction and scantlings Materials. Thermosetting resins, glass-fibre reinforcement, reference laminate |
| I.S. EN 50342-5:2010 | LEAD-ACID STARTER BATTERIES - PART 5: PROPERTIES OF BATTERY HOUSINGS AND HANDLES |
| BS EN 16153 : 2013 | LIGHT TRANSMITTING FLAT MULTIWALL POLYCARBONATE (PC) SHEETS FOR INTERNAL AND EXTERNAL USE IN ROOFS, WALLS AND CEILINGS - REQUIREMENTS AND TEST METHODS |
| DIN EN 15502-2-1:2013-01 | GAS-FIRED CENTRAL HEATING BOILERS - PART 2-1: SPECIFIC STANDARD FOR TYPE C APPLIANCES AND TYPE B2, B3 AND B5 APPLIANCES OF A NOMINAL HEAT INPUT NOT EXCEEDING 1000 KW |
| 14/30303797 DC : 0 | BS EN 438-7 - HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 7: COMPACT LAMINATE AND HPL COMPOSITE PANELS FOR INTERNAL AND EXTERNAL WALL AND CEILING FINISHES |
| EN 438-9:2017 | High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually called laminates) - Part 9: Classification and specifications for alternative core laminates |
| I.S. EN 14963:2006 | ROOF COVERINGS - CONTINUOUS ROOFLIGHTS OF PLASTICS WITH OR WITHOUT UPSTANDS - CLASSIFICATION, REQUIREMENTS AND TEST METHODS |
| EN ISO 899-2:2003/A1:2015 | Plastics - Determination of creep behaviour - Part 2: Flexural creep by three-point loading - Amendment 1 (ISO 899-2:2003/Amd 1:2015) |
| I.S. EN 12566-3:2016 | SMALL WASTEWATER TREATMENT SYSTEMS FOR UP TO 50 PT - PART 3: PACKAGED AND/OR SITE ASSEMBLED DOMESTIC WASTEWATER TREATMENT PLANTS |
| EN 60950-22:2017 | Information technology equipment - Safety - Part 22: Equipment to be installed outdoors |
| DIN EN 13121-1:2003-10 | GRP tanks and vessels for use above ground - Part 1: Raw materials; Specification conditions and acceptance conditions |
| EN IEC 60079-7:2015/A1:2018 | EXPLOSIVE ATMOSPHERES - PART 7: EQUIPMENT PROTECTION BY INCREASED SAFETY 'E' (IEC 60079-7:2015/A1:2017) |
| DIN EN 14598-3:2005-07 | Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 3: Specific requirements |
| EN 13121-1:2003 | GRP TANKS AND VESSELS FOR USE ABOVE GROUND - PART 1: RAW MATERIALS - SPECIFICATION CONDITIONS AND ACCEPTANCE CONDITIONS |
| DIN EN 26:2015-08 | Gas-fired instantaneous water heaters for the production of domestic hot water |
| DIN EN 14598-1:2005-07 | Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 1: Designation |
| BS EN 14471 : 2013 | CHIMNEYS - SYSTEM CHIMNEYS WITH PLASTIC FLUE LINERS - REQUIREMENTS AND TEST METHODS |
| BS EN 13785 : 2005 | REGULATORS WITH A CAPACITY OF UP TO AND INCLUDING 100 KG/H, HAVING A MAXIMUM NOMINAL OUTLET PRESSURE OF UP TO AND INCLUDING 4 BAR, OTHER THAN THOSE COVERED BY EN 12864 AND THEIR ASSOCIATED SAFETY DEVICES FOR BUTANE, PROPANE OR THEIR MIXTURES |
| BS EN 15347:2007 | Plastics. Recycled Plastics. Characterization of plastics waste |
| BS EN 14879-2:2006 | Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media Coatings on metallic components |
| DIN EN 15342 E : 2008 | PLASTICS - RECYCLED PLASTICS - CHARACTERIZATION OF POLYSTYRENE (PS) RECYCLATES |
| BS EN ISO 1622-2:1999 | Plastics. Polystrene (PS) moulding and extrusion materials Preparation of test specimens and determination of properties |
| BS EN ISO 11542-2 : 1999 | PLASTICS - ULTRA-HIGH-MOLECULAR-WEIGHT POLYETHYLENE (PE-UHMW) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| BS EN 13677-2:2003 | Reinforced thermoplastic moulding compounds. Specification for GMT Methods of test and general requirements |
| UNE-EN 16245-2:2014 | Fibre-reinforced plastic composites - Declaration of raw material characteristics - Part 2: Specific requirements for resin, curing systems, additives and modifiers |
| BS EN 438-7:2005 | High-pressure decorative laminates (HPL). Sheets based on thermosetting resins (usually called laminates) Compact laminate and HPL composite panels for internal and external wall and ceiling finishes |
| BS EN 1873 : 2014 | PREFABRICATED ACCESSORIES FOR ROOFING - INDIVIDUAL ROOFLIGHTS OF PLASTICS - PRODUCT SPECIFICATION AND TEST METHODS |
| BS EN 13786 : 2004 | AUTOMATIC CHANGE-OVER VALVES HAVING A MAXIMUM OUTLET PRESSURE OF UP TO AND INCLUDING 4 BAR WITH A CAPACITY OF UP TO AND INCLUDING 100 KG/H, AND THEIR ASSOCIATED SAFETY DEVICES FOR BUTANE, PROPANE OR THEIR MIXTURES |
| BS EN 13892-1:2002 | Methods of test for screed materials Sampling, making and curing specimens for test |
| BS EN 60893-2:2004 | Insulating materials. Industrial rigid laminated sheets based on thermosetting resins for electrical purposes Methods of test |
| BS EN 14879-5:2007 | Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media Linings on concrete components |
| I.S. EN ISO 7823-1:2003 | PLASTICS - POLY(METHYL METHACRYLATE) SHEETS - TYPES, DIMENSIONS AND CHARACTERISTICS - PART 1: CAST SHEETS |
| EN 16129:2013 | Pressure regulators, automatic change-over devices, having a maximum regulated pressure of 4 bar, with a maximum capacity of 150 kg/h, associated safety devices and adaptors for butane, propane, and their mixtures |
| DIN EN 438-8:2009-07 | HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 8: CLASSIFICATION AND SPECIFICATIONS FOR DESIGN LAMINATES |
| EN 12201-2:2011+A1:2013 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 2: Pipes |
| DIN EN 13813:2003-01 | SCREED MATERIAL AND FLOOR SCREEDS - SCREED MATERIALS - PROPERTIES AND REQUIREMENTS |
| EN 62208:2011 | Empty enclosures for low-voltage switchgear and controlgear assemblies - General requirements |
| EN 12566-3:2016 | Small wastewater treatment systems for up to 50 PT - Part 3: Packaged and/or site assembled domestic wastewater treatment plants |
| EN 12080:2017 | Railway applications - Axleboxes - Rolling bearings |
| CEN/TS 15534-1:2007 | Wood-plastics composites (WPC) - Part 1: Test methods for characterisation of WPC materials and products |
| DIN EN 14879-2:2007-02 | Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media - Part 2: Coatings on metallic components |
| EN 60216-2:2005 | Electrical insulating materials - Thermal endurance properties - Part 2: Determination of thermal endurance properties of electrical insulating materials - Choice of test criteria |
| EN 1013:2012+A1:2014 | LIGHT TRANSMITTING SINGLE SKIN PROFILED PLASTICS SHEETS FOR INTERNAL AND EXTERNAL ROOFS, WALLS AND CEILINGS - REQUIREMENTS AND TEST METHODS |
| EN 50342-5 : 2010 COR 2011 | LEAD-ACID STARTER BATTERIES - PART 5: PROPERTIES OF BATTERY HOUSINGS AND HANDLES |
| DIN EN 15502-2-1:2017-09 | Gas-fired central heating boilers - Part 2-1: Specific standard for type C appliances and type B2, B3 and B5 appliances of a nominal heat input not exceeding 1 000 kW (includes Amendment 1:2016) |
| EN 13160-7:2016 | Leak detection systems - Part 7: Requirements and test/assessment methods for interstitial spaces, leak detection linings and leak detection jackets |
| EN 13245-3:2010 | Plastics - Unplasticized poly(vinyl chloride) (PVC-U) profiles for building applications - Part 3: Designation of PVC-UE profiles |
| EN 60950-1:2006/A2:2013 | INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60950-1:2005/A2:2013, MODIFIED) |
| EN 60893-2:2004 | Insulating materials - Industrial rigid laminated sheets based on thermosetting resins for electrical purposes - Part 2: Methods of test |
| CEN/TS 1852-3:2003/A1:2005 | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - POLYPROPYLENE (PP) - PART 3: GUIDANCE FOR INSTALLATION |
| VDI/VDE 2252 Blatt 2:2007-09 | Precision engineering components - Guides - Synthetic gliding bearings |
| ENV 1401-3:2001 | Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) - Part 3: Guidance for installation |
| ONORM EN ISO 11542-2 : 2009 | PLASTICS - ULTRA-HIGH-MOLECULAR-WEIGHT POLYETHYLENE (PE-UHMW) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| BS EN 438-8:2009 | High-pressure decorative laminates (HPL). Sheets based on thermosetting resins (usually called laminates) Classification and specifications for design laminates |
| BS EN 50617-1:2015 | Railway applications. Technical parameters of train detection systems for the interoperability of the trans-European railway system Track circuits |
| I.S. EN 12608:2003 | UNPLASTICIZED POLYVINYLCHLORIDE (PVC-U) PROFILES FOR THE FABRICATION OF WINDOWS AND DOORS - CLASSIFICATION, REQUIREMENTS AND TEST METHODS |
| 12/30258456 DC : 0 | BS EN 60950-1:2006/FPRAE:2011 - INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS |
| BS EN 16129:2013 | Pressure regulators, automatic change-over devices, having a maximum regulated pressure of 4 bar, with a maximum capacity of 150 kg/h, associated safety devices and adaptors for butane, propane, and their mixtures |
| I.S. EN 483:2000 | GAS-FIRED CENTRAL HEATING BOILERS - TYPE C BOILERS OF NOMINAL HEAT INPUT NOT EXCEEDING 70 KW |
| 10/30218935 DC : 0 | BS EN 15502-2-1 - GAS-FIRED HEATING BOILERS - PART 2-1: SPECIFIC STANDARD FOR TYPE C APPLIANCES AND TYPE B[2], B[3] AND B[5] APPLIANCES OF A NOMINAL HEAT INPUT NOT EXCEEDING 1000 KW |
| 11/30239977 DC : 0 | BS EN 16245-2 - FIBRE-REINFORCED PLASTIC COMPOSITES - DECLARATION OF RAW MATERIAL CHARACTERISTICS - PART 2: ADDITIONAL REQUIREMENTS FOR RESINS, CURING SYSTEMS, ADDITIVES AND MODIFIERS |
| DIN EN 12608-1 E : 2016 | UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) PROFILES FOR THE FABRICATION OF WINDOWS AND DOORS - CLASSIFICATION, REQUIREMENTS AND TEST METHODS - PART 1: NON-COATED PVC-U PROFILES WITH LIGHT COLOURED SURFACES |
| DIN EN 16245-2:2013-08 | Fibre-reinforced plastic composites - Declaration of raw material characteristics - Part 2: Specific requirements for resin, curing systems, additives and modifiers |
| DIN EN 15564 E : 2009 | PRECAST CONCRETE PRODUCTS - RESIN BOUND CONCRETE - REQUIREMENTS AND TEST METHODS |
| PREN 16129 : DRAFT 2010 | PRESSURE REGULATORS, AUTOMATIC CHANGE-OVER DEVICES, HAVING A MAXIMUM REGULATED PRESSURE OF 4 BAR, WITH A MAXIMUM CAPACITY OF 100 KG/H, ASSOCIATED SAFETY DEVICES AND ADAPTORS FOR BUTANE, PROPANE, AND THEIR MIXTURES |
| EN 15344:2007 | Plastics - Recycled Plastics - Characterisation of Polyethylene (PE) recyclates |
| BS EN 12608-1:2016 | Unplasticized poly(vinyl chloride) (PVC-U) profiles for the fabrication of windows and doors. Classification, requirements and test methods Non-coated PVC-U profiles with light coloured surfaces |
| PREN 438-9 : DRAFT 2016 | HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 9: CLASSIFICATION AND SPECIFICATIONS FOR ALTERNATIVE CORE LAMINATES |
| 05/30135769 DC : DRAFT JUL 2005 | EN 15274 - GENERAL PURPOSE ADHESIVES FOR STRUCTURAL ASSEMBLY - REQUIREMENTS AND TEST METHODS |
| BS EN 15534-1 : 2014 | COMPOSITES MADE FROM CELLULOSE-BASED MATERIALS AND THERMOPLASTICS (USUALLY CALLED WOOD-POLYMER COMPOSITES (WPC) OR NATURAL FIBRE COMPOSITES (NFC)) - PART 1: TEST METHODS FOR CHARACTERISATION OF COMPOUNDS AND PRODUCTS |
| EN 4702-05:2017 | Aerospace series - Quick release fastening systems for non-structural and lining applications - Part 05: Retaining washer |
| 12/30265756 DC : 0 | BS EN 845-1 - SPECIFICATION FOR ANCILLARY COMPONENTS FOR MASONRY - PART 1: WALL TIES, TENSION STRAPS, HANGERS AND BRACKETS |
| 14/30301266 DC : 0 | BS EN 13160-7 - LEAK DETECTION SYSTEMS - PART 7: REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR INTERSTITIAL SPACES, LEAK DETECTION LININGS AND LEAK DETECTION JACKETS |
| 11/30250549 DC : 0 | BS EN 14471 - CHIMNEYS - SYSTEM CHIMNEYS WITH PLASTIC FLUE LINERS - REQUIREMENTS AND TEST METHODS |
| BS EN 62208:2011 | Empty enclosures for low-voltage switchgear and controlgear assemblies. General requirements |
| 15/30304304 DC : 0 | BS EN 12080 - RAILWAY APPLICATIONS - AXLEBOXES - ROLLING BEARINGS |
| 04/30109201 DC : DRAFT OCT 2004 | EN 14879-2 - ORGANIC COATING SYSTEMS AND LININGS FOR PROTECTION OF INDUSTRIAL APPARATUS AND PLANTS AGAINST CORROSION CAUSED BY AGGRESSIVE MEDIA - PART 2: COATINGS ON METALLIC COMPONENTS |
| DD CEN/TS 15534-1:2007 | Wood-plastics composites (WPC) Test methods for characterisation of WPC materials and products |
| BS EN 50465:2015 | European product standard for combined heating power systems using gas fuel |
| UNI EN 15345 : 2008 | PLASTICS - RECYCLED PLASTICS - CHARACTERISATION OF POLYPROPYLENE (PP) RECYCLATES |
| PREN 4691-1 : DRAFT 2015 | AEROSPACE SERIES - TIE ROD WITH INTEGRATED BOLTS - PART 1: TECHNICAL SPECIFICATION |
| PREN 13813 : DRAFT 2017 | SCREED MATERIAL AND FLOOR SCREEDS - SCREED MATERIAL - PROPERTIES AND REQUIREMENTS |
| BS EN 60079-7 : 2015 | EXPLOSIVE ATMOSPHERES - PART 7: EQUIPMENT PROTECTION BY INCREASED SAFETY 'E' (IEC 60079-7:2015) |
| I.S. EN ISO 9093-2:2002 | SMALL CRAFT - SEACOCKS AND THROUGH-HULL FITTINGS - PART 2: NON-METALLIC |
| CEI EN 62208 : 2012 | EMPTY ENCLOSURES FOR LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES - GENERAL REQUIREMENTS |
| PREN 14471 : DRAFT 2011 | CHIMNEYS - SYSTEM CHIMNEYS WITH PLASTIC FLUE LINERS - REQUIREMENTS AND TEST METHODS |
| PREN 513 : DRAFT 2017 | PLASTICS - POLY(VINYL CHLORIDE) (PVC) BASED PROFILES - DETERMINATION OF THE RESISTANCE TO ARTIFICIAL WEATHERING |
| ISO 7823-2:2003 | Plastics — Poly(methyl methacrylate) sheets — Types, dimensions and characteristics — Part 2: Extruded sheets |
| PREN 12080 : DRAFT 2015 | RAILWAY APPLICATIONS - AXLEBOXES - ROLLING BEARINGS |
| EN 50465 : 2015 | GAS APPLIANCES - COMBINED HEAT AND POWER APPLIANCE OF NOMINAL HEAT INPUT INFERIOR OR EQUAL TO 70 KW |
| EN 438-8:2009 | High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (Usually called Laminates) - Part 8: Classification and specifications for design laminates |
| UNI EN 438-8 : 2009 | HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 8: CLASSIFICATION AND SPECIFICATIONS FOR DESIGN LAMINATES |
| I.S. EN 50465:2015 | GAS APPLIANCES - COMBINED HEAT AND POWER APPLIANCE OF NOMINAL HEAT INPUT INFERIOR OR EQUAL TO 70 KW |
| DIN EN 14879-5 E : 2007 | ORGANIC COATING SYSTEMS AND LININGS FOR PROTECTION OF INDUSTRIAL APPARATUS AND PLANTS AGAINST CORROSION CAUSED BY AGGRESSIVE MEDIA - PART 5: LININGS ON CONCRETE COMPONENTS |
| I.S. EN 13121-1:2003 | GRP TANKS AND VESSELS FOR USE ABOVE GROUND - PART 1: RAW MATERIALS - SPECIFICATION CONDITIONS AND ACCEPTANCE CONDITIONS |
| DIN EN 89:2015-08 | GAS-FIRED STORAGE WATER HEATERS FOR THE PRODUCTION OF DOMESTIC HOT WATER |
| DIN EN 15347:2008-02 | Plastics - Recycled Plastics - Characterisation of plastics wastes |
| DIN EN 15347 E : 2008 | PLASTICS - RECYCLED PLASTICS - CHARACTERISATION OF PLASTICS WASTES |
| DIN EN 1504-4:2005-02 | Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part 4: Structural bonding; German version EN 1504-4:2004 |
| DIN EN 12080:2015-06 (Draft) | RAILWAY APPLICATIONS - AXLEBOXES - ROLLING BEARINGS |
| DIN EN 15344:2008-02 | Plastics - Recycled Plastics - Characterisation of Polyethylene (PE) recyclates |
| DIN EN 14471:2015-03 | CHIMNEYS - SYSTEM CHIMNEYS WITH PLASTIC FLUE LINERS - REQUIREMENTS AND TEST METHODS |
| BS EN 13566-4:2002 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks Lining with cured-in-place pipes |
| BS EN 26:1998 | Gas fired instantaneous water heaters for the production of domestic hot water, fitted with atmospheric burners |
| DIN EN 15274:2015-06 | GENERAL PURPOSE ADHESIVES FOR STRUCTURAL ASSEMBLY - REQUIREMENTS AND TEST METHODS |
| BS EN 438-2 : 2016 | HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 2: DETERMINATION OF PROPERTIES |
| BS EN 12080:2017 | Railway applications. Axleboxes. Rolling bearings |
| UNE-EN 438-4:2016 | High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (Usually called Laminates) - Part 4: Classification and specifications for compact laminates of thickness 2 mm and greater |
| I.S. EN 14471:2013 | CHIMNEYS - SYSTEM CHIMNEYS WITH PLASTIC FLUE LINERS - REQUIREMENTS AND TEST METHODS |
| I.S. EN 13160-7:2016 | LEAK DETECTION SYSTEMS - PART 7: REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR INTERSTITIAL SPACES, LEAK DETECTION LININGS AND LEAK DETECTION JACKETS |
| I.S. EN 61212-2:2006 | INSULATING MATERIALS - INDUSTRIAL RIGID ROUND LAMINATED TUBES AND RODS BASED ON THERMOSETTING RESINS FOR ELECTRICAL PURPOSES - PART 2: METHODS OF TEST |
| I.S. EN 12080:2017 | RAILWAY APPLICATIONS - AXLEBOXES - ROLLING BEARINGS |
| I.S. EN 60893-2:2004 | INSULATING MATERIALS - INDUSTRIAL RIGID LAMINATED SHEETS BASED ON THERMOSETTING RESINS FOR ELECTRICAL PURPOSES - PART 2: METHODS OF TEST |
| DIN EN 12608:2003-09 | UNPLASTICIZED POLYVINYLCHLORIDE (PVC-U) PROFILES FOR THE FABRICATION OF WINDOWS AND DOORS - CLASSIFICATION, REQUIREMENTS AND TEST METHODS |
| I.S. EN 13245-1:2010 | PLASTICS - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) PROFILES FOR BUILDING APPLICATIONS - PART 1: DESIGNATION OF PVC-U PROFILES |
| I.S. EN 12201-2:2011 | PLASTICS PIPING SYSTEMS FOR WATER SUPPLY, AND FOR DRAINAGE AND SEWERAGE UNDER PRESSURE - POLYETHYLENE (PE) - PART 2: PIPES |
| I.S. EN 26:2015 | GAS-FIRED INSTANTANEOUS WATER HEATERS FOR THE PRODUCTION OF DOMESTIC HOT WATER |
| I.S. EN ISO 4894-2:1999 | PLASTICS - STYRENE/ACRYLONITRILE (SAN) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| I.S. EN 1873:2014 | PREFABRICATED ACCESSORIES FOR ROOFING - INDIVIDUAL ROOFLIGHTS OF PLASTICS - PRODUCT SPECIFICATION AND TEST METHODS |
| I.S. EN 438-4:2016 | HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 4: CLASSIFICATION AND SPECIFICATIONS FOR COMPACT LAMINATES OF THICKNESS 2 MM AND GREATER |
| I.S. EN ISO 11542-2:1999 | PLASTICS - ULTRA-HIGH-MOLECULAR-WEIGHT POLYETHYLENE (PE-UHMW) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| EN ISO 11542-2:1998/AC:2008 | PLASTICS - ULTRA-HIGH-MOLECULAR-WEIGHT POLYETHYLENE (PE-UHMW) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| I.S. EN ISO 899-2:2003 | PLASTICS - DETERMINATION OF CREEP BEHAVIOUR - PART 2: FLEXURAL CREEP BY THREE-POINT LOADING (ISO 899-2:2003) |
| I.S. EN 15274:2015 | GENERAL PURPOSE ADHESIVES FOR STRUCTURAL ASSEMBLY - REQUIREMENTS AND TEST METHODS |
| DIN EN 1873:2016-07 | PREFABRICATED ACCESSORIES FOR ROOFING - INDIVIDUAL ROOFLIGHTS OF PLASTICS - PRODUCT SPECIFICATION AND TEST METHODS |
| DIN EN 12080:2017-11 | Railway applications - Axleboxes - Rolling bearings |
| I.S. EN 438-6:2016 | HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 6: CLASSIFICATION AND SPECIFICATIONS FOR EXTERIOR-GRADE COMPACT LAMINATES OF THICKNESS 2 MM AND GREATER |
| I.S. EN 89:2015 | GAS-FIRED STORAGE WATER HEATERS FOR THE PRODUCTION OF DOMESTIC HOT WATER |
| I.S. EN 845-1:2013 | SPECIFICATION FOR ANCILLARY COMPONENTS FOR MASONRY - PART 1: WALL TIES, TENSION STRAPS, HANGERS AND BRACKETS |
| VDI 3822 Blatt 2.1.8:2012-01 | Failure analysis - Defects of thermoplastic products made of plastics caused by weather-induced stress |
| VDI 2083 Blatt 9.2:2017-01 | Cleanroom technology - Consumables in the cleanroom |
| VDI 2200:2007-06 | Tight flange connections - Selection, calculation, design and assembly of bolted flange connections |
| BS EN 50342-5:2010 | Lead-acid starter batteries Properties of battery housings and handles |
| DD CEN/TS 14758-3:2006 | Plastics piping systems for non-pressure underground drainage and sewerage. Polypropylene with mineral modifier(s)(PP-MD) Guidance for installation |
| BS EN 4702-03:2017 | Aerospace series. Quick release fastening systems for non-structural and lining applications Stud - quick-release and locking |
| 14/30300568 DC : 0 | BS EN 15274 - GENERAL PURPOSE ADHESIVES FOR STRUCTURAL ASSEMBLY - REQUIREMENTS AND TEST METHODS |
| BS EN 16240:2013 | Light transmitting flat solid polycarbonate (PC) sheets for internal and external use in roofs, walls and ceilings. Requirements and test methods |
| DD CEN/TS 1852-3:2003 | Plastics piping systems for non-pressure underground drainage and sewerage. Polypropylene (PP) Guidance for installation |
| 14/30303791 DC : 0 | BS EN 438-6 - HIGH-PRESSURE DECORATIVE (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 6: CLASSIFICATION AND SPECIFICATIONS FOR EXTERIOR-GRADE COMPACT LAMINATES OF THICKNESS 2 MM AND GREATER |
| PREN 1504-4 : DRAFT 2016 | PRODUCTS AND SYSTEMS FOR THE PROTECTION AND REPAIR OF CONCRETE - DEFINITIONS, REQUIREMENTS, QUALITY CONTROL AND EVALUATION OF CONFORMITY - PART 4: STRUCTURAL BONDING |
| DIN EN 15564:2009-05 | PRECAST CONCRETE PRODUCTS - RESIN BOUND CONCRETE - REQUIREMENTS AND TEST METHODS |
| UNI EN 15347 : 2008 | PLASTICS - RECYCLED PLASTICS - CHARACTERISATION OF PLASTICS WASTES |
| 12/30258334 DC : 0 | BS EN 1013 - LIGHT TRANSMITTING SINGLE SKIN PROFILED PLASTIC SHEETS FOR INTERNAL AND EXTERNAL ROOFS, WALLS AND CEILINGS - REQUIREMENTS AND TEST METHODS |
| UNI EN 15564 : 2009 | PRECAST CONCRETE PRODUCTS - RESIN BOUND CONCRETE - REQUIREMENTS AND TEST METHODS |
| 08/30194094 DC : 0 | BS EN 13245-3 - PLASTICS - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) PROFILES FOR BUILDING APPLICATIONS - PART 3: DESIGNATION OF PVC-UE PROFILES |
| BS EN 60455-2:2015 | Resin based reactive compounds used for electrical insulation Methods of test |
| BS EN 61241-0:2006 | Electrical apparatus for use in the presence of combustible dust General requirements |
| 14/30303779 DC : 0 | BS EN 438-4 - HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 4: CLASSIFICATION AND SPECIFICATIONS FOR COMPACT LAMINATES OF THICKNESS 2 MM AND GREATER |
| UNE-EN 16129:2014 | Pressure regulators, automatic change-over devices, having a maximum regulated pressure of 4 bar, with a maximum capacity of 150 kg/h, associated safety devices and adaptors for butane, propane, and their mixtures |
| 12/30265313 DC : 0 | BS EN 124-6 - GULLY TOPS AND MANHOLE TOPS FOR VEHICULAR AND PEDESTRIAN AREAS - PART 6: GULLY TOPS AND MANHOLE TOPS MADE FROM POLYPROPYLENE (PP) OR POLYVINYL-CHLORIDE (PVC-U) |
| 07/30166095 DC : 0 | EN 124 - GULLY TOPS AND MANHOLE TOPS FOR VEHICULAR AND PEDESTRIAN AREAS |
| DIN EN 14963:2006-12 | Roof coverings - Continuous rooflights of plastics with or without upstands - Classification, requirements and test methods |
| 11/30238648 DC : DRAFT FEB 2011 | BS EN 16240 - LIGHT TRANSMITTING FLAT SOLID POLYCARBONATE (PC) SHEETS FOR INTERNAL AND EXTERNAL ROOFS, WALLS AND CEILINGS - REQUIREMENTS AND TEST METHODS |
| BS ISO 7391-2 : 1996 AMD 10746 | PLASTICS - POLYCARBONATE (PC) MOULDING AND EXTRUSION MATERIALS - PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| EN 4702-03 : 2017 | AEROSPACE SERIES - QUICK RELEASE FASTENING SYSTEMS FOR NON-STRUCTURAL AND LINING APPLICATIONS - PART 03: STUD - QUICK-RELEASE AND LOCKING |
| UNE-EN 12608-1:2016 | Unplasticized poly(vinyl chloride) (PVC-U) profiles for the fabrication of windows and doors - Classification, requirements and test methods - Part 1: Non-coated PVC-U profiles with light coloured surfaces |
| PREN 4702-03 : DRAFT 2016 | AEROSPACE SERIES - QUICK RELEASE FASTENING SYSTEMS WITH NON METALLIC STUD FOR NON-STRUCTURAL APPLICATIONS - PART 03: STUD - QUICK-RELEASE AND LOCKING |
| DIN EN 16153:2015-05 | LIGHT TRANSMITTING FLAT MULTIWALL POLYCARBONATE (PC) SHEETS FOR INTERNAL AND EXTERNAL USE IN ROOFS, WALLS AND CEILINGS - REQUIREMENTS AND TEST METHODS |
| EN 438-2:2016 | High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually called laminates) - Part 2: Determination of properties |
| UNE-EN 62208:2012 | Empty enclosures for low-voltage switchgear and controlgear assemblies - General requirements |
| I.S. EN 60544-2:2012 | ELECTRICAL INSULATING MATERIALS - DETERMINATION OF THE EFFECTS OF IONIZING RADIATION ON INSULATING MATERIALS - PART 2: PROCEDURES FOR IRRADIATION AND TEST (IEC 60544-2:2012 (EQV)) |
| CEI EN 62368-1 : 2016 | AUDIO/VIDEO, INFORMATION AND COMMUNICATION TECHNOLOGY EQUIPMENT - PART 1: SAFETY REQUIREMENTS |
| UNI EN 15342 : 2008 | PLASTICS - RECYCLED PLASTICS - CHARACTERIZATION OF POLYSTYRENE (PS) RECYCLATES |
| I.S. CEN TS 14758-3:2006 | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - POLYPROPYLENE WITH MINERAL MODIFIER(S) (PP-MD) - PART 3: GUIDANCE FOR INSTALLATION |
| I.S. EN 4691-1:2017 | AEROSPACE SERIES - TIE ROD WITH INTEGRATED BOLTS - PART 1: TECHNICAL SPECIFICATION |
| I.S. EN 62752:2016&AC:2019-03 | IN-CABLE CONTROL AND PROTECTION DEVICE FOR MODE 2 CHARGING OF ELECTRIC ROAD VEHICLES (IC-CPD) |
| BS EN 1013 : 2012 | LIGHT TRANSMITTING SINGLE SKIN PROFILED PLASTICS SHEETS FOR INTERNAL AND EXTERNAL ROOFS, WALLS AND CEILINGS - REQUIREMENTS AND TEST METHODS |
| I.S. EN 60455-2:2015 | RESIN BASED REACTIVE COMPOUNDS USED FOR ELECTRICAL INSULATION - PART 2: METHODS OF TEST |
| I.S. EN 16240:2013 | LIGHT TRANSMITTING FLAT SOLID POLYCARBONATE (PC) SHEETS FOR INTERNAL AND EXTERNAL USE IN ROOFS, WALLS AND CEILINGS - REQUIREMENTS AND TEST METHODS |
| BS EN 15502-2-1 : 2012 | GAS-FIRED CENTRAL HEATING BOILERS - PART 2-1: SPECIFIC STANDARD FOR TYPE C APPLIANCES AND TYPE B2, B3 AND B5 APPLIANCES OF A NOMINAL HEAT INPUT NOT EXCEEDING 1000 KW |
| PREN 438-7 : DRAFT 2014 | HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 7: COMPACT LAMINATE AND HPL COMPOSITE PANELS FOR INTERNAL AND EXTERNAL WALL AND CEILING FINISHES |
| I.S. EN 61439-1:2011 | LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES - PART 1: GENERAL RULES (IEC 61439-1:2011) |
| I.S. EN 438-2:2016 | HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 2: DETERMINATION OF PROPERTIES |
| I.S. EN 16245-2:2013 | FIBRE-REINFORCED PLASTIC COMPOSITES - DECLARATION OF RAW MATERIAL CHARACTERISTICS - PART 2: SPECIFIC REQUIREMENTS FOR RESIN, CURING SYSTEMS, ADDITIVES AND MODIFIERS |
| EN 4691-1:2017 | Aerospace series - Tie rod with integrated bolts - Part 1: Technical specification |
| I.S. EN 13245-3:2010 | PLASTICS - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) PROFILES FOR BUILDING APPLICATIONS - PART 3: DESIGNATION OF PVC-UE PROFILES |
| I.S. EN 60950-1:2006 | INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60950-1:2005 (MOD)) |
| UNI EN 13245-3 : 2010 | PLASTICS - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) PROFILES FOR BUILDING APPLICATIONS - PART 3: DESIGNATION OF PVC-UE PROFILES |
| EN ISO 14125:1998/A1:2011 | FIBRE-REINFORCED PLASTIC COMPOSITES - DETERMINATION OF FLEXURAL PROPERTIES |
| DIN EN 14879-2 E : 2007 | ORGANIC COATING SYSTEMS AND LININGS FOR PROTECTION OF INDUSTRIAL APPARATUS AND PLANTS AGAINST CORROSION CAUSED BY AGGRESSIVE MEDIA - PART 2: COATINGS ON METALLIC COMPONENTS |
| DIN EN 13785:2010-05 | REGULATORS WITH A CAPACITY OF UP TO AND INCLUDING 100 KG/H, HAVING A MAXIMUM NOMINAL OUTLET PRESSURE OF UP TO AND INCLUDING 4 BAR, OTHER THAN THOSE COVERED BY EN 12864 AND THEIR ASSOCIATED SAFETY DEVICES FOR BUTANE, PROPANE OR THEIR MIXTURES |
| DIN EN 438-4:2016-06 | HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 4: CLASSIFICATION AND SPECIFICATIONS FOR COMPACT LAMINATES OF THICKNESS 2 MM AND GREATER |
| DIN EN 438-7:2005-04 | High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually called laminates) - Part 7: Compact laminate and HPL composite panels for internal and external wall and ceiling finishes; German version EN 438-7:2005 |
| DIN EN 13786:2010-07 | AUTOMATIC CHANGE-OVER VALVES HAVING A MAXIMUM OUTLET PRESSURE OF UP TO AND INCLUDING 4 BAR WITH A CAPACITY OF UP TO AND INCLUDING 100 KG/H, AND THEIR ASSOCIATED SAFETY DEVICES FOR BUTANE, PROPANE OR THEIR MIXTURES |
| DIN EN 14471 E : 2015 | CHIMNEYS - SYSTEM CHIMNEYS WITH PLASTIC FLUE LINERS - REQUIREMENTS AND TEST METHODS |
| DIN EN 15342:2008-02 | Plastics - Recycled Plastics - Characterization of polystyrene (PS) recyclates |
| BS EN 13121-1:2003 | GRP tanks and vessels for use above ground Raw materials. Specification conditions and acceptance conditions |
| BS EN 89:2015 | Gas-fired storage water heaters for the production of domestic hot water |
| BS EN 12201-2 : 2011 | PLASTICS PIPING SYSTEMS FOR WATER SUPPLY, AND FOR DRAINAGE AND SEWERAGE UNDER PRESSURE - POLYETHYLENE (PE) - PART 2: PIPES |
| BS EN 12608:2003 | Unplasticized polyvinylchloride (PVC-U) profiles for the fabrication of windows and doors. Classification, requirements and test methods |
| UNE-EN 62109-1:2011 | Safety of power converters for use in photovoltaic power systems -- Part 1: General requirements |
| DIN EN 15274 E : 2015 | GENERAL PURPOSE ADHESIVES FOR STRUCTURAL ASSEMBLY - REQUIREMENTS AND TEST METHODS |
| DIN EN 15344 E : 2008 | PLASTICS - RECYCLED PLASTICS - CHARACTERISATION OF POLYETHYLENE (PE) RECYCLATES |
| UNE-EN 60950-1:2007 | Information technology equipment - Safety - Part 1: General requirements |
| EN 12608-1 : 2016 | UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) PROFILES FOR THE FABRICATION OF WINDOWS AND DOORS - CLASSIFICATION, REQUIREMENTS AND TEST METHODS - PART 1: NON-COATED PVC-U PROFILES WITH LIGHT COLOURED SURFACES |
| EN 16240:2013 | Light transmitting flat solid polycarbonate (PC) sheets for internal and external use in roofs, walls and ceilings - Requirements and test methods |
| EN 16245-2:2013 | Fibre-reinforced plastic composites - Declaration of raw material characteristics - Part 2: Specific requirements for resin, curing systems, additives and modifiers |
| UNI EN 13245-1 : 2010 | PLASTICS - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) PROFILES FOR BUILDING APPLICATIONS - PART 1: DESIGNATION OF PVC-U PROFILES |
| EN 50465:2015 | Gas appliances - Combined heat and power appliance of nominal heat input inferior or equal to 70 kW |
| UNI EN 16245-2 : 2013 | FIBRE-REINFORCED PLASTIC COMPOSITES - DECLARATION OF RAW MATERIAL CHARACTERISTICS - PART 2: SPECIFIC REQUIREMENTS FOR RESIN, CURING SYSTEMS, ADDITIVES AND MODIFIERS |
| UNI EN 12201-2 : 2013 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 2: Pipes |
| EN 483:1999/A4:2007 | GAS-FIRED CENTRAL HEATING BOILERS - TYPE C BOILERS OF NOMINAL HEAT INPUT NOT EXCEEDING 70 KW |
| I.S. EN ISO 14125:1998 | FIBRE-REINFORCED PLASTIC COMPOSITES - DETERMINATION OF FLEXURAL PROPERTIES |
| UNI EN 13786 : 2009 | AUTOMATIC CHANGE-OVER VALVES HAVING A MAXIMUM OUTLET PRESSURE OF UP TO AND INCLUDING 4 BAR WITH A CAPACITY OF UP TO AND INCLUDING 100 KG/H, AND THEIR ASSOCIATED SAFETY DEVICES FOR BUTANE, PROPANE OR THEIR MIXTURES |
| UNI EN 13785 : 2009 | REGULATORS WITH A CAPACITY OF UP TO AND INCLUDING 100 KG/H, HAVING A MAXIMUM NOMINAL OUTLET PRESSURE OF UP TO AND INCLUDING 4 BAR, OTHER THAN THOSE COVERED BY EN 12864 AND THEIR ASSOCIATED SAFETY DEVICES FOR BUTANE, PROPANE OR THEIR MIXTURES |
| UNI EN 16129 : 2013 | PRESSURE REGULATORS, AUTOMATIC CHANGE-OVER DEVICES, HAVING A MAXIMUM REGULATED PRESSURE OF 4 BAR, WITH A MAXIMUM CAPACITY OF 150 KG/H, ASSOCIATED SAFETY DEVICES AND ADAPTORS FOR BUTANE, PROPANE, AND THEIR MIXTURES |
| DIN EN 13245-3:2010-11 | Plastics - Unplasticized poly(vinyl chloride) (PVC-U) profiles for building applications - Part 3: Designation of PVC-UE profiles |
| UNI EN 15344 : 2008 | PLASTICS - RECYCLED PLASTICS - CHARACTERISATION OF POLYETHYLENE (PE) RECYCLATES |
| 16/30337049 DC : 0 | BS EN 50290-2-34 - COMMUNICATION CABLES - PART 2-34: COMMON DESIGN RULES AND CONSTRUCTION - POLYETHYLENE SHEATHING COMPOUND FOR OUTDOOR OPTICAL FIBRE CABLES |
| I.S. EN 13566-4:2003 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 4: LINING WITH CURED-IN-PLACE PIPES |
| 16/30340635 DC : 0 | BS EN 438-9 - HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 9: CLASSIFICATION AND SPECIFICATIONS FOR ALTERNATIVE CORE LAMINATES |
| BS EN 16245-2:2013 | Fibre-reinforced plastic composites. Declaration of raw material characteristics Specific requirements for resin, curing systems, additives and modifiers |
| 12/30266170 DC : 0 | BS EN 15534-1 - COMPOSITES MADE FROM CELLULOSE-BASED MATERIALS AND THERMOPLASTICS (USUALLY CALLED WOOD-POLYMER COMPOSITES (WPC) OR NATURAL FIBRE COMPOSITES (NFC)) - PART 1 : TEST METHODS FOR CHARACTERISATION OF COMPOUNDS AND PRODUCTS |
| BS EN 13245-3:2010 | Plastics. Unplasticized poly(vinyl chloride) (PVCU) profiles for building applications Designation of PVC-UE profiles |
| 10/30212147 DC : 0 | BS EN 12201-2 - PLASTICS PIPING SYSTEMS FOR WATER SUPPLY, AND FOR DRAINAGE AND SEWERAGE UNDER PRESSURE - POLYETHYLENE (PE) - PART 2: PIPES |
| UNE-EN 50617-1:2015 | Railway applications - Technical parameters of train detection systems for the interoperability of the trans-European railway system - Part 1: Track circuits |
| DIN EN 15345 E : 2008 | PLASTICS - RECYCLED PLASTICS - CHARACTERISATION OF POLYPROPYLENE (PP) RECYCLATES |
| DD ENV 1401-3:2001 | Plastics piping systems for non-pressure underground drainage and sewerage. Unplasticized poly(vinylchloride) (PVC-U) Guidance for installation |
| 04/30055611 DC : 0 | BS EN 124 - GULLY TOPS AND MANHOLE TOPS FOR VEHICULAR AND PEDESTRIAN AREAS |
| DIN EN 16240:2014-03 | LIGHT TRANSMITTING FLAT SOLID POLYCARBONATE (PC) SHEETS FOR INTERNAL AND EXTERNAL USE IN ROOFS, WALLS AND CEILINGS - REQUIREMENTS AND TEST METHODS |
| 08/30189974 DC : DRAFT DEC 2008 | BS EN 13245-1 - PLASTICS - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) PROFILES FOR BUILDING APPLICATIONS - PART 1: DESIGNATION OF PVC-U PROFILES |
| PREN 15274 : DRAFT 2014 | GENERAL PURPOSE ADHESIVES FOR STRUCTURAL ASSEMBLY - REQUIREMENTS AND TEST METHODS |
| 10/30217061 DC : 0 | BS EN 50342-5 ED1 - LEAD-ACID STARTER BATTERIES - PART 5: PROPERTIES OF BATTERY HOUSINGS AND HANDLES |
| 03/119348 DC : 0 | PREN 1013-1 - LIGHT TRANSMITTING SINGLE SKIN PROFILED PLASTICS SHEETING FOR INTERNAL AND EXTERNAL ROOFING, WALL CLADDING AND CEILING FINISHES - PART 1: GENERAL REQUIREMENTS AND TEST METHODS |
| DD CEN/TS 15534-2:2007 | Wood-plastics composites (WPC) Characterisation of WPC materials |
| 12/30258453 DC : 0 | BS EN 62368-1 AMD - AUDIO/VIDEO, INFORMATION AND COMMUNICATION TECHNOLOGY EQUIPMENT - PART 1: SAFETY REQUIREMENTS |
| UNE-EN 438-2:2016 | High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (Usually called Laminates) - Part 2: Determination of properties |
| BS EN 15345:2007 | Plastics. Recycled plastics. Characterization of polypropylene (PP) recyclates |
| BS EN 60371-2:2004 | Specification for insulating materials based on mica Methods of test |
| I.S. EN 15502-2-1:2012 | GAS-FIRED CENTRAL HEATING BOILERS - PART 2-1: SPECIFIC STANDARD FOR TYPE C APPLIANCES AND TYPE B2, B3 AND B5 APPLIANCES OF A NOMINAL HEAT INPUT NOT EXCEEDING 1000 KW |
| BS EN 60950-22:2017 | Information technology equipment. Safety Equipment to be installed outdoors |
| 06/30137905 DC : DRAFT MAR 2006 | ISO 19072-2 - ROAD VEHICLES - CONNECTION INTERFACE FOR PYROTECHNIC DEVICES, TWO WAY AND THREE WAY CONNECTIONS - PART 2: TEST METHODS AND GENERAL PERFORMANCES REQUIREMENTS |
| UNE-EN 50342-5:2011 | Lead-acid starter batteries -- Part 5: Properties of battery housings and handles |
| I.S. EN 438-9:2017 | HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 9: CLASSIFICATION AND SPECIFICATIONS FOR ALTERNATIVE CORE LAMINATES |
| I.S. EN 60950-22:2017 | INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 22: EQUIPMENT TO BE INSTALLED OUTDOORS |
| I.S. EN 62368-1:2014 | AUDIO/VIDEO, INFORMATION AND COMMUNICATION TECHNOLOGY EQUIPMENT - PART 1: SAFETY REQUIREMENTS (IEC 62368-1:2014, MODIFIED) |
| I.S. EN 60851-3:2009 | WINDING WIRES - TEST METHODS - PART 3: MECHANICAL PROPERTIES (IEC 60851-3:2009 (EQV)) |
| I.S. EN 438-8:2009 | HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 8: CLASSIFICATION AND SPECIFICATIONS FOR DESIGN LAMINATES |
| I.S. EN 1013:2012 | LIGHT TRANSMITTING SINGLE SKIN PROFILED PLASTICS SHEETS FOR INTERNAL AND EXTERNAL ROOFS, WALLS AND CEILINGS - REQUIREMENTS AND TEST METHODS |
| CEI EN 60216-2 : 2006 | ELECTRICAL INSULATING MATERIALS - THERMAL ENDURANCE PROPERTIES - PART 2: DETERMINATION OF THERMAL ENDURANCE PROPERTIES OF ELECTRICAL INSULATING MATERIALS - CHOICE OF TEST CRITERIA |
| EN 62368-1:2014/AC:2017-03 | AUDIO/VIDEO, INFORMATION AND COMMUNICATION TECHNOLOGY EQUIPMENT - PART 1: SAFETY REQUIREMENTS (IEC 62368-1:2014, MODIFIED) |
| EN ISO 9093-2:2002 | Small craft - Seacocks and through-hull fittings - Part 2: Non-metallic (ISO 9093-2:2002) |
| I.S. EN 60371-2:2005 | SPECIFICATION FOR INSULATING MATERIALS BASED ON MICA - PART 2: METHODS OF TEST |
| BS EN ISO 9093-2:2002 | Small craft. Seacocks and through-hull fittings Non-metallic |
| ISO 9093-2:2002 | Small craft Seacocks and through-hull fittings Part 2: Non-metallic |
| DIN EN 438-2:2016-06 | HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 2: DETERMINATION OF PROPERTIES |
| S.R. CEN/TS 15534-2:2007 | WOOD-PLASTICS COMPOSITES (WPC) - PART 2: CHARACTERISATION OF WPC MATERIALS |
| I.S. EN 62208:2011 | EMPTY ENCLOSURES FOR LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES - GENERAL REQUIREMENTS (IEC 62208:2011) |
| I.S. EN 15345:2007 | PLASTICS - RECYCLED PLASTICS - CHARACTERISATION OF POLYPROPYLENE (PP) RECYCLATES |
| I.S. EN 61241-0:2006 | ELECTRICAL APPARATUS FOR USE IN THE PRESENCE OF COMBUSTIBLE DUST - PART 0: GENERAL REQUIREMENTS |
| I.S. EN 15564:2008 | PRECAST CONCRETE PRODUCTS - RESIN BOUND CONCRETE - REQUIREMENTS AND TEST METHODS |
| UNE-EN 12201-2:2012 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 2: Pipes |
| DIN EN ISO 14125:2011-05 | Fibre-reinforced plastic composites - Determination of flexural properties (ISO 14125:1998 + Cor 1:2001 + Amd 1:2011) |
| DIN EN ISO 11542-2:2010-01 | Plastics - Ultra-high-molecular-weight polyethylene (PE-UHMW) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 11542-2:1998 + Cor. 1:2007) (includes Corrigendum AC:2008) |
| DIN EN 438-6:2016-06 | HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 6: CLASSIFICATION AND SPECIFICATIONS FOR EXTERIOR-GRADE COMPACT LAMINATES OF THICKNESS 2 MM AND GREATER |
| 02/124520 DC : DRAFT DEC 2002 | EN 14598-3 - REINFORCED THERMOSETTING MOULDING COMPOUNDS - SPECIFICATION FOR SHEET MOULDING COMPOUND (SMC) AND BULK MOULDING COMPOUND (BMC) - PART 3: SPECIFIC REQUIREMENTS |
| ISO 9054:1990 | Cellular plastics, rigid — Test methods for self-skinned, high-density materials |
| 11/30242263 DC : 0 | BS EN 4691-001 - AEROSPACE SERIES - TIE ROD WITH INTEGRATED BOLTS - TECHNICAL SPECIFICATION |
| BS EN 845-1 : 2013 | SPECIFICATION FOR ANCILLARY COMPONENTS FOR MASONRY - PART 1: WALL TIES, TENSION STRAPS, HANGERS AND BRACKETS |
| BS EN 438-6:2016 | High-pressure decorative laminates (HPL). Sheets based on thermosetting resins (usually called laminates) Classification and specifications for Exterior-grade compact laminates of thickness 2 mm and greater |
| BS EN 12576:1998 | Plastics. Fibre reinforced composites. Preparation of compression moulded test plates of SMC, BMC and DMC |
| BS EN 13677-3:2003 | Reinforced thermoplastic moulding compounds. Specification for GMT Specific requirements |
| EN 62752:2016 | In-cable control and protection device for mode 2 charging of electric road vehicles (IC-CPD) |
| BS EN 13160-7:2003 | Leak detection systems General requirements and test methods for interstitial spaces, leak protecting linings and leak protecting jackets |
| BS EN ISO 3672-2:2001 | Plastics. Unsaturated-polyester resins (UP-R) Preparation of test specimens and determination of properties |
| UNE-EN 12566-3:2017 | Small wastewater treatment systems for up to 50 PT - Part 3: Packaged and/or site assembled domestic wastewater treatment plants |
| BS EN 438-4:2016 | High-pressure decorative laminates (HPL). Sheets based on thermosetting resins (usually called laminates) Classification and specifications for compact laminates of thickness 2 mm and greater |
| BS EN 1504-4:2004 | Products and systems for the protection and repair of concrete structures. Definitions, requirements, quality control and evaluation of conformity Structural bonding |
| BS EN 12566-3 : 2005 | SMALL WASTEWATER TREATMENT SYSTEMS FOR UP TO 50 PT - PART 3: PACKAGED AND/OR SITE ASSEMBLED DOMESTIC WASTEWATER TREATMENT PLANTS |
| BS EN ISO 899-2 : 2003 | PLASTICS - DETERMINATION OF CREEP BEHAVIOUR - PART 2: FLEXURAL CREEP BY THREE-POINT LOADING |
| UNE-EN 60079-0:2013 | Explosive atmospheres - Part 0: Equipment - General requirements |
| BS EN 62109-1:2010 | Safety of power converters for use in photovoltaic power systems General requirements |
| DIN EN 15334 E : 2007 | SANITARY APPLIANCES - METHACRYLIC DISPERSIONS OF HIGH FILLER CONTENT |
| DIN EN 13245-1 E : 2010 | PLASTICS - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) PROFILES FOR BUILDING APPLICATIONS - PART 1: DESIGNATION OF PVC-U PROFILES |
| UNE-EN 15274:2015 | General purpose adhesives for structural assembly - Requirements and test methods |
| DIN EN 13245-1:2010-11 | Plastics - Unplasticized poly(vinyl chloride) (PVC-U) profiles for building applications - Part 1: Designation of PVC-U profiles |
| BS EN ISO 7823-2:2003 | Plastics. Poly(methyl methacrylate) sheets. Types, dimensions and characteristics Extruded sheets |
| ISO 4894-2:1995 | Plastics Styrene/acrylonitrile (SAN) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties |
| BS EN 483 : 2000 | GAS-FIRED CENTRAL HEATING BOILERS - TYPE C BOILERS OF NOMINAL HEAT INPUT NOT EXCEEDING 70 KW |
| ISO 3672-2:2000 | Plastics — Unsaturated-polyester resins (UP-R) — Part 2: Preparation of test specimens and determination of properties |
| ISO 7823-1:2003 | Plastics — Poly(methyl methacrylate) sheets — Types, dimensions and characteristics — Part 1: Cast sheets |
| BS EN 13245-1:2010 | Plastics. Unplasticized poly(vinyl chloride) (PVC-U) profiles for building applications Designation of PVC-U profiles |
| BS EN ISO 7823-1:2003 | Plastics. Poly(methyl methacrylate) sheets. Types, dimensions and characteristics Cast sheets |
| BS EN 13813:2002 | Screed material and floor screeds. Screed material. Properties and requirements |
| BS EN 14598-3:2005 | Reinforced thermosetting moulding compounds. Specification for sheet moulding compound (SMC) and bulk moulding compound (BMC) Specific requirements |
| BS EN 60950-1 : 2006 | INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS |
| ISO 11542-2:1998 | Plastics Ultra-high-molecular-weight polyethylene (PE-UHMW) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties |
| UNE-EN 1013:2013 | Light transmitting single skin profiled plastics sheets for internal and external roofs, walls and ceilings - Requirements and test methods |
| UNE-EN 1873:2015 | Prefabricated accessories for roofing - Individual rooflights of plastics - Product specification and test methods |
| BS EN 15342:2007 | Plastics. Recycled plastics. Characterization of polystyrene (PS) recyclates |
| UNE-EN 89:2016 | Gas-fired storage water heaters for the production of domestic hot water |
| UNE-EN 26:2016 | Gas-fired instantaneous water heaters for the production of domestic hot water |
| UNE-EN 438-6:2016 | High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (Usually called Laminates) - Part 6: Classification and specifications for Exterior-grade compact laminates of thickness 2 mm and greater |
| BS EN 4691-1:2017 | Aerospace series. Tie rod with integrated bolts Technical specification |
| DIN EN 15334:2007-05 | Sanitary appliances - Methacrylic dispersions of high filler content |
| ISO 899-2:2003 | Plastics Determination of creep behaviour Part 2: Flexural creep by three-point loading |
| EN 61241-0:2006 | Electrical apparatus for use in the presence of combustible dust - Part 0: General requirements |
| EN 15334:2007 | Sanitary appliances - Methacrylic dispersions of high filler content |
| EN 15342:2007 | Plastics - Recycled Plastics - Characterization of polystyrene (PS) recyclates |
| EN 89:2015 | Gas-fired storage water heaters for the production of domestic hot water |
| EN 14879-2:2006 | Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media - Part 2: Coatings on metallic components |
| EN 14879-5:2007 | Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media - Part 5: Linings on concrete components |
| EN ISO 15252-2 : 1999 | PLASTICS - EPOXY POWDER MOULDING COMPOUNDS (EP-PMCS) - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| EN 845-1:2013+A1:2016 | Specification for ancillary components for masonry - Part 1: Wall ties, tension straps, hangers and brackets |
| EN 13786:2004+A1:2008 | Automatic change-over valves having a maximum outlet pressure of up to and including 4 bar with a capacity of up to and including 100 kg/h, and their associated safety devices for butane, propane or their mixtures |
| EN 14471:2013+A1:2015 | CHIMNEYS - SYSTEM CHIMNEYS WITH PLASTIC FLUE LINERS - REQUIREMENTS AND TEST METHODS |
| EN 16153:2013+A1:2015 | Light transmitting flat multiwall polycarbonate (PC) sheets for internal and external use in roofs, walls and ceilings - Requirements and test methods |
| EN 1504-4:2004 | Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part 4: Structural bonding |
| EN 13677-3:2003 | Reinforced thermoplastic moulding compounds - Specification for GMT - Part 3: Specific requirements |
| EN 14963:2006 | Roof coverings - Continuous rooflights of plastics with or without upstands - Classification, requirements and test methods |
| EN 13677-2:2003 | Reinforced thermoplastic moulding compounds - Specification for GMT - Part 2: Methods of test and general requirements |
| EN 438-6:2016 | High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually called laminates) - Part 6: Classification and specifications for Exterior-grade compact laminates of thickness 2 mm and greater |
| EN ISO 14529-2 : 1999 | PLASTICS - MELAMINE/PHENOLIC POWDER MOULDING COMPOUNDS (MP-PMCS) - PART 2 - PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| EN 15347:2007 | Plastics - Recycled Plastics - Characterisation of plastics wastes |
| EN 13785:2005+A1:2008 | Regulators with a capacity of up to and including 100 kg/h, having a maximum nominal outlet pressure of up to and including 4 bar, other than those covered by EN 12864 and their associated safety devices for butane, propane or their mixtures |
| EN 438-4:2016 | High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually called laminates) - Part 4: Classification and specifications for compact laminates of thickness 2 mm and greater |
| EN 15345:2007 | Plastics - Recycled Plastics - Characterisation of Polypropylene (PP) recyclates |
| EN 13892-1:2002 | Methods of test for screed materials - Part 1: Sampling, making and curing specimens for test |
| EN ISO 3672-2 : 2001 | PLASTICS - UNSATURATED-POLYESTER RESINS (UP-R) - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| EN ISO 11248 : 1999 | Plastics - Thermosetting moulding materials - Evaluation of short-term performance at elevated temperatures (ISO 11248:1993) |
| EN ISO 9054 : 1999 | CELLULAR PLASTICS, RIGID - TEST METHODS FOR SELF-SKINNED, HIGH-DENSITY MATERIALS |
| EN ISO 14530-2 : 1999 | PLASTICS - UNSATURATED-POLYESTER POWDER MOULDING COMPOUNDS (UP-PMCS) - PART 2 - PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| EN 15274:2015 | General purpose adhesives for structural assembly - Requirements and test methods |
| EN 1873:2014+A1:2016 | Prefabricated accessories for roofing - Individual rooflights of plastics - Product specification and test methods |
| EN 15502-2-1:2012+A1:2016 | Gas-fired central heating boilers - Part 2-1: Specific standard for type C appliances and type B2, B3 and B5 appliances of a nominal heat input not exceeding 1 000 kW |
| EN 26:2015 | Gas-fired instantaneous water heaters for the production of domestic hot water |
| EN ISO 7823-1:2003 | Plastics - Poly(methyl methacrylate) sheets - Types, dimensions and characteristics - Part 1: Cast sheets (ISO 7823-1:2003) |
| EN 438-7:2005 (edition 2) | High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (Usually called Laminates) - Part 7: Compact laminate and HPL composite panels for internal and external wall and ceiling finishes |
| EN ISO 4894-2 : 1999 | PLASTICS - STYRENE/ACRYLONITRILE (SAN) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| EN ISO 14528-2 : 1999 | PLASTICS - MELAMINE/PHENOLIC POWDER MOULDING COMPOUNDS (MP-PMCS) - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| EN ISO 7823-2 : 2003 | PLASTICS - POLY(METHYL METHACRYLATE) SHEETS - TYPES, DIMENSIONS AND CHARACTERISTICS - PART 2: EXTRUDED SHEETS |
| EN 14598-3:2005 | Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 3: Specific requirements |
| EN 14598-1:2005 | Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 1: Designation |
| EN 15564:2008 | Precast concrete products - Resin bound concrete - Requirements and test methods |
| EN 13813:2002 | Screed material and floor screeds - Screed material - Properties and requirements |
| EN ISO 14527-2 : 1999 | PLASTICS - UREA-FORMALDEHYDE AND UREA/MELAMINE-FORMALDEHYDE POWDER MOULDING COMPOUNDS (UF- AND UF/MF-PMCS) - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| EN 1825-1:2004/AC:2006 | GREASE SEPARATORS - PART 1: PRINCIPLES OF DESIGN, PERFORMANCE AND TESTING, MARKING AND QUALITY CONTROL |
| BS EN 14963:2006 | Roof coverings. Continuous rooflights of plastics with or without upstands. Classification, requirements and test methods |
| PREN 438-4 : DRAFT 2014 | HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 4: CLASSIFICATION AND SPECIFICATIONS FOR COMPACT LAMINATES OF THICKNESS 2 MM AND GREATER |
| DIN EN 1013:2015-03 | LIGHT TRANSMITTING SINGLE SKIN PROFILED PLASTICS SHEETS FOR INTERNAL AND EXTERNAL ROOFS, WALLS AND CEILINGS - REQUIREMENTS AND TEST METHODS |
| I.S. EN 4702-03:2017 | AEROSPACE SERIES - QUICK RELEASE FASTENING SYSTEMS FOR NON-STRUCTURAL AND LINING APPLICATIONS - PART 03: STUD - QUICK-RELEASE AND LOCKING |
| I.S. EN 438-7:2005 | HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 7: COMPACT LAMINATE AND HPL COMPOSITE PANELS FOR INTERNAL AND EXTERNAL WALL AND CEILING FINISHES |
| I.S. EN 13244-2:2002 | PLASTICS PIPING SYSTEMS FOR BURIED AND ABOVE-GROUND PRESSURE SYSTEMS FOR WATER FOR GENERAL PURPOSES DRAINAGE AND SEWERAGE - POLYETHYLENE (PE) - PIPES |
| CEI EN 60893-2 : 2005 | INSULATING MATERIALS - INDUSTRIAL RIGID LAMINATED SHEETS BASED ON THERMOSETTING RESINS FOR ELECTRICAL PURPOSES - PART 2: METHODS OF TEST |
| CEI EN 62752 : 1ED 2017 | IN-CABLE CONTROL AND PROTECTION DEVICE FOR MODE 2 CHARGING OF ELECTRIC ROAD VEHICLES (IC-CPD) |
| PREN 438-8 : DRAFT 2017 | HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 8: CLASSIFICATION AND SPECIFICATIONS FOR DESIGN LAMINATES |
| BS EN 60544-2:2012 | Electrical insulating materials. Determination of the effects of ionizing radiation on insulating materials Procedures for irradiation and test |
| DIN EN 16129:2013-08 | Pressure regulators, automatic change-over devices, having a maximum regulated pressure of 4 bar, with a maximum capacity of 150kg/h, associated safety devices and adaptors for butane, propane, and their mixtures |
| 07/30169818 DC : 0 | BS EN 1013 - LIGHT TRANSMITTING SINGLE SKIN PROFILED PLASTICS SHEETS FOR INTERNAL AND EXTERNAL ROOFS, WALLS AND CEILINGS - REQUIREMENTS AND TEST METHODS |
| NF EN 13245-3 : 2010 | PLASTICS - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) PROFILES FOR BUILDING APPLICATIONS - PART 3: DESIGNATION OF PVC-UE PROFILES |
| I.S. EN 15344:2007 | PLASTICS - RECYCLED PLASTICS - CHARACTERISATION OF POLYETHYLENE (PE) RECYCLATES |
| 04/30099887 DC : DRAFT MAY 2004 | PREN 14963 - ROOF COVERINGS - CONTINUOUS ROOFLIGHTS OF PLASTICS WITH UPSTANDS - CLASSIFICATION, REQUIREMENTS AND TEST METHODS |
| 02/124518 DC : DRAFT DEC 2002 | EN 14598-1 - REINFORCED THERMOSETTING MOULDING COMPOUNDS - SPECIFICATION FOR SHEET MOULDING COMPOUND (SMC) AND BULK MOULDING COMPOUND (BMC) - PART 1: DESIGNATION |
| PREN 438-6 : DRAFT 2014 | HIGH-PRESSURE DECORATIVE (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 6: CLASSIFICATION AND SPECIFICATIONS FOR EXTERIOR-GRADE COMPACT LAMINATES OF THICKNESS 2 MM AND GREATER |
| UNE-EN 13245-3:2011 | Plastics - Unplasticized poly(vinyl chloride) (PVC-U) profiles for building applications - Part 3: Designation of PVC-UE profiles |
| UNI EN 1013 : 2015 | LIGHT TRANSMITTING SINGLE SKIN PROFILED PLASTICS SHEETS FOR INTERNAL AND EXTERNAL ROOFS, WALLS AND CEILINGS - REQUIREMENTS AND TEST METHODS |
| BS EN 438-9:2017 | High-pressure decorative laminates (HPL). Sheets based on thermosetting resins (usually called laminates) Classification and specifications for alternative core laminates |
| I.S. EN 60079-7:2015 | EXPLOSIVE ATMOSPHERES - PART 7: EQUIPMENT PROTECTION BY INCREASED SAFETY 'E' |
| I.S. EN 12608-1:2016 | UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) PROFILES FOR THE FABRICATION OF WINDOWS AND DOORS - CLASSIFICATION, REQUIREMENTS AND TEST METHODS - PART 1: NON-COATED PVC-U PROFILES WITH LIGHT COLOURED SURFACES |
| I.S. EN 16153:2013 | LIGHT TRANSMITTING FLAT MULTIWALL POLYCARBONATE (PC) SHEETS FOR INTERNAL AND EXTERNAL USE IN ROOFS, WALLS AND CEILINGS - REQUIREMENTS AND TEST METHODS |
| I.S. EN 16129:2013 | PRESSURE REGULATORS, AUTOMATIC CHANGEOVER DEVICES, HAVING A MAXIMUM REGULATED PRESSURE OF 4 BAR, WITH A MAXIMUM CAPACITY OF 150 KG/H, ASSOCIATED SAFETY DEVICES AND ADAPTORS FOR BUTANE, PROPANE, AND THEIR MIXTURES |
| I.S. EN 15534-1:2014 | COMPOSITES MADE FROM CELLULOSE-BASED MATERIALS AND THERMOPLASTICS (USUALLY CALLED WOOD-POLYMER COMPOSITES (WPC) OR NATURAL FIBRE COMPOSITES (NFC)) - PART 1: TEST METHODS FOR CHARACTERISATION OF COMPOUNDS AND PRODUCTS |
| I.S. EN 50617-1:2015 | RAILWAY APPLICATIONS - TECHNICAL PARAMETERS OF TRAIN DETECTION SYSTEMS FOR THE INTEROPERABILITY OF THE TRANS-EUROPEAN RAILWAY SYSTEM - PART 1: TRACK CIRCUITS |
| I.S. EN 60216-2:2005 | ELECTRICAL INSULATING MATERIALS - THERMAL ENDURANCE PROPERTIES - PART 2: DETERMINATION OF THERMAL ENDURANCE PROPERTIES OF ELECTRICAL INSULATING MATERIALS - CHOICE OF TEST CRITERIA |
| BS EN 60079-0 : 2012 | EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS |
| 17/30361211 DC : 0 | BS EN 513 - PLASTICS - POLY(VINYL CHLORIDE) (PVC) BASED PROFILES - DETERMINATION OF THE RESISTANCE TO ARTIFICIAL WEATHERING |
| PREN 50290-2-34 : DRAFT 2016 | COMMUNICATION CABLES - PART 2-34: COMMON DESIGN RULES AND CONSTRUCTION - POLYETHYLENE SHEATHING COMPOUND FOR OUTDOOR OPTICAL FIBRE CABLES |
| UNE-EN 62752:2017 | In-cable control and protection device for mode 2 charging of electric road vehicles (IC-CPD) |
| UNE-EN 60079-7:2016 | Explosive atmospheres - Part 7: Equipment protection by increased safety "e" |
| BS EN 60851-3 : 2009 | WINDING WIRES - TEST METHODS - PART 3: MECHANICAL PROPERTIES |
| S.R. CEN TS 15534-1:2007 | WOOD-PLASTICS COMPOSITES (WPC) - PART 1: TEST METHODS FOR CHARACTERISATION OF WPC MATERIALS AND PRODUCTS |
| DIN EN 12201-2:2013-12 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 2: Pipes (includes Amendment A1:2013) |
| DIN EN 1504-4:2016-05 (Draft) | PRODUCTS AND SYSTEMS FOR THE PROTECTION AND REPAIR OF CONCRETE STRUCTURES - DEFINITIONS, REQUIREMENTS, QUALITY CONTROL AND EVALUATION OF CONFORMITY - PART 4: STRUCTURAL BONDING |
| UNE-EN 61439-1:2012 | Low-voltage switchgear and controlgear assemblies - Part 1: General rules |
| UNE-EN 13245-1:2011 | Plastics - Unplasticized poly(vinyl chloride) (PVC-U) profiles for building applications - Part 1: Designation of PVC-U profiles |
| BS EN 15274:2015 | General purpose adhesives for structural assembly. Requirements and test methods |
| BS EN ISO 1163-2:2000 | Plastics. Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials Preparation of test specimens and determination of properties |
| BS EN 1825-1:2004 | Grease separators Principles of design, performance and testing, marking and quality control |
| BS EN 15334:2007 | Sanitary appliances. Methacrylic dispersions of high filler content |
| BS EN 15344:2007 | Plastics. Recycled plastics. Characterization of polyethylene (PE) recyclates |
| BS EN 61439-1:2011 | Low-voltage switchgear and controlgear assemblies General rules |
| BS EN 13244-2:2002 | Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage. Polyethylene (PE) Pipes |
| BS EN 61212-2:2006 | Insulating materials. Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes Methods of test |
| BS EN 14598-1:2005 | Reinforced thermosetting moulding compounds. Specification for sheet moulding compound (SMC) and bulk moulding compound (BMC) Designation |
| EN 61212-2:2006 | Insulating materials - Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes - Part 2: Methods of test |
| EN 60079-0:2012/A11:2013 | EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS (IEC 60079-0:2011, MODIFIED) |
| EN 13566-4:2002 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 4: Lining with cured-in-place pipes |
| CEN/TS 14758-3:2006 | Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifier(s) (PP-MD) - Part 3: Guidance for installation |
| EN 12608:2003 | Unplasticized polyvinylchloride (PVC-U) profiles for the fabrication of windows and doors - Classification, requirements and test methods |
| EN 60371-2:2004 | Specification for insulating materials based on mica - Part 2: Methods of test |
| EN 60544-2:2012 | Electrical insulating materials - Determination of the effects of ionizing radiation on insulating materials - Part 2: Procedures for irradiation and test |
| DIN EN 14879-5:2007-10 | Organic coating systems and linings for protection of industrial apparatus and plants against corrosion caused by aggressive media - Part 5: Linings on concrete components |
| DIN EN 13244-2:2003-04 | PLASTICS PIPING SYSTEMS FOR BURIED AND ABOVE-GROUND PRESSURE SYSTEMS FOR WATER FOR GENERAL PURPOSES, DRAINAGE AND SEWERAGE - POLYETHYLENE (PE) - PART 2: PIPES |
| DIN EN 12608-1:2016-08 | UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) PROFILES FOR THE FABRICATION OF WINDOWS AND DOORS - CLASSIFICATION, REQUIREMENTS AND TEST METHODS - PART 1: NON-COATED PVC-U PROFILES WITH LIGHT COLOURED SURFACES |
| DIN EN 483:2000-06 | GAS-FIRED CENTRAL HEATING BOILERS - TYPE C BOILERS OF NOMINAL HEAT INPUT NOT EXCEEDING 70 KW |
| DIN EN 1825-1:2004-12 | Grease separators - Part 1: Principles of design, performance and testing, marking and quality control; German version EN 1825-1:2004 |
| CEN/TS 15534-2:2007 | Wood-plastics composites (WPC) - Part 2: Characterisation of WPC materials |
| EN 13245-1:2010 | Plastics - Unplasticized poly(vinyl chloride) (PVC-U) profiles for building applications - Part 1: Designation of PVC-U profiles |
| EN 13244-2:2002 | Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 2: Pipes |
| EN 60455-2:2015 | Resin based reactive compounds used for electrical insulation - Part 2: Methods of test |
| EN 50617-1:2015 | Railway applications - Technical parameters of train detection systems for the interoperability of the trans-European railway system - Part 1: Track circuits |
| DIN EN 13892-1:2003-02 | METHODS OF TEST FOR SCREED MATERIALS - PART 1: SAMPLING - MAKING AND CURING SPECIMENS FOR TESTING |
| EN 62109-1 : 2010 | SAFETY OF POWER CONVERTERS FOR USE IN PHOTOVOLTAIC POWER SYSTEMS - PART 1: GENERAL REQUIREMENTS |
| UNE-EN 16153:2013 | Light transmitting flat multiwall polycarbonate (PC) sheets for internal and external use in roofs, walls and ceilings - Requirements and test methods |
| ISO 10350-2:2011 | Plastics Acquisition and presentation of comparable single-point data Part 2: Long-fibre-reinforced plastics |
| ISO 293:2004 | Plastics — Compression moulding of test specimens of thermoplastic materials |
| ISO 23529:2016 | Rubber General procedures for preparing and conditioning test pieces for physical test methods |
| ISO 295:2004 | Plastics — Compression moulding of test specimens of thermosetting materials |
| ISO 10350-1:2017 | Plastics — Acquisition and presentation of comparable single-point data — Part 1: Moulding materials |
| ISO 10724-1:1998 | Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 1: General principles and moulding of multipurpose test specimens |
| ISO 527-2:2012 | Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics |
| ISO 9513:2012 | Metallic materials — Calibration of extensometer systems used in uniaxial testing |
| ISO 2602:1980 | Statistical interpretation of test results Estimation of the mean Confidence interval |
| ISO 1209-2:2007 | Rigid cellular plastics Determination of flexural properties Part 2: Determination of flexural strength and apparent flexural modulus of elasticity |
| ISO 472:2013 | Plastics Vocabulary |
| ISO 291:2008 | Plastics Standard atmospheres for conditioning and testing |
| ISO 14125:1998 | Fibre-reinforced plastic composites Determination of flexural properties |
| ISO 294-1:2017 | Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens |
| ISO 7500-1:2015 | Metallic materials Calibration and verification of static uniaxial testing machines Part 1: Tension/compression testing machines Calibration and verification of the force-measuring system |
| ISO 2818:1994 | Plastics — Preparation of test specimens by machining |
| ISO 20753:2008 | Plastics Test specimens |
| ISO 16012:2015 | Plastics Determination of linear dimensions of test specimens |
| ISO 1209-1:2007 | Rigid cellular plastics Determination of flexural properties Part 1: Basic bending test |
Sorry this product is not available in your region.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.