Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

I.S. CEN TS 14807:2004

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

PLASTICS PIPING SYSTEMS - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON UNSATURATED POLYESTER RESIN (UP) - GUIDANCE FOR THE STRUCTURAL ANALYSIS OF BURIED GRP-UP PIPELINES
Available format(s)

Hardcopy , PDF

Superseded date

21-12-2013

Language(s)

English

Published date

01-01-2004

Preview

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Requirements
5 Classification and designation
Bibliography

Specifies limits applicable to glass-reinforced thermosetting plastics (GRP) pipes used for the conveyance of liquids under pressure or gravity conditions.

DocumentType
Standard
Pages
14
PublisherName
National Standards Authority of Ireland
Status
Superseded
SupersededBy

EN 1227 : 1997 PLASTICS PIPING SYSTEMS - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) PIPES - DETERMINATION OF THE LONG-TERM ULTIMATE RELATIVE RING DEFLECTION UNDER WET CONDITIONS
EN 1295-1:1997 Structural design of buried pipelines under various conditions of loading - Part 1: General requirements
ISO/TR 10465-2:2007 Underground installation of flexible glass-reinforced pipes based on unsaturated polyester resin (GRP-UP) Part 2: Comparison of static calculation methods
EN 805:2000 Water supply - Requirements for systems and components outside buildings
ISO/TR 10465-3:2007 Underground installation of flexible glass-reinforced pipes based on unsaturated polyester resin (GRP-UP) Part 3: Installation parameters and application limits
PREN 14364 : DRAFT 2011 PLASTICS PIPING SYSTEMS FOR DRAINAGE AND SEWERAGE WITH OR WITHOUT PRESSURE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON UNSATURATED POLYESTER RESIN (UP) - SPECIFICATIONS FOR PIPES, FITTINGS AND JOINTS
EN 1120:1996 Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes and fittings - Determination of the resistance to chemical attack from the inside of a section in a deflected condition
ISO 14828:2003 Glass-reinforced thermosetting plastics (GRP) pipes Determination of the long-term specific ring relaxation stiffness under wet conditions and calculation of the wet relaxation factor
EN 1447:2009+A1:2010 Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of long-term resistance to internal pressure
ISO/TR 10465-1:1993 Underground installation of flexible glass-reinforced thermosetting resin (GRP) pipes Part 1: Installation procedures
EN 1226:1996 Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Test method to prove the resistance to initial ring deflection
ISO 10468:2003 Glass-reinforced thermosetting plastics (GRP) pipes Determination of the long-term specific ring creep stiffness under wet conditions and calculation of the wet creep factor
PREN 1796 : DRAFT 2011 PLASTICS PIPING SYSTEMS FOR WATER SUPPLY WITH OR WITHOUT PRESSURE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON UNSATURATED POLYESTER RESIN (UP)
ISO 10471:2003 Glass-reinforced thermosetting plastics (GRP) pipes Determination of the long-term ultimate bending strain and the long-term ultimate relative ring deflection under wet conditions
EN 1228:1996 Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of initial specific ring stiffness
EN 1610:2015 Construction and testing of drains and sewers
EN 705:1994/AC:1995 PLASTICS PIPING SYSTEMS - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) PIPES AND FITTINGS - METHODS FOR REGRESSION ANALYSES AND THEIR USE
CEN/TS 14578:2013 Plastics piping systems for water supply or drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Recommended practice for installation
ENV 1046:2001 Plastics piping and ducting systems - Systems outside building structures for the conveyance of water or sewage - Practices for installation above and below ground

View more information
$66.40
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more