Customer Support: 131 242

i2i Intertek.com
  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Go to AMERICAS site
Dismiss alert
Please enter a keyword to search
Advanced search

I.S. EN 12516-1:2014

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

INDUSTRIAL VALVES - SHELL DESIGN STRENGTH - PART 1: TABULATION METHOD FOR STEEL VALVE SHELLS
Available format(s)

Hardcopy , PDF

Superseded date

21-01-2020

Published date

26-11-2014

Publisher

National Standards Authority of Ireland

Preview

For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.

Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and units
5 Material groups and material temperature limitations
6 Pressure/temperature (p/t) ratings
7 Temperature effects
8 Dimensions
9 Auxiliary connections
10 End dimensions
11 Marking
Annex A (normative) Methods used for establishing pressure/temperature ratings
Annex B (normative) Material groups
Annex C (informative) Special Class
Annex D (informative) Radiographic procedure and acceptance standards
Annex E (informative) Magnetic particle examination procedure and acceptance standards
Annex F (informative) Liquid penetrant examination procedure and acceptance standards
Annex G (informative) Ultrasonic examination procedure and acceptance standards
Annex H (informative) Requirement for Limited Class valves in sizes DN 65 and smaller
Annex I (informative) ASTM/ASME material
Annex J (informative) Relationship between DN, NPS, pipe inside diameter Dni, pipe outside diameter OD
Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 97/23/EC (Pressure Equipment Directive)
Bibliography

This European Standard specifies the tabulation method for determining the wall thickness of valve bodies, bonnets and covers with essentially circular cross-section made in forged, cast or fabricated steel.

Committee
TC 69
DocumentType
Standard
Pages
206
ProductNote
NOTE: The date of any NSAI previous adoption may not match the date of its original CEN/CENELEC document. THIS STANDARD ALSO REFERS TO EN 10213:2007,ASME Section II
PublisherName
National Standards Authority of Ireland
Status
Superseded
SupersededBy
Supersedes

EN ISO 9692-1:2013 Welding and allied processes - Types of joint preparation - Part 1: Manual metal arc welding, gas-shielded metal arc welding, gas welding, TIG welding and beam welding of steels (ISO 9692-1:2013)
EN 10228-3:1998 Non-destructive testing of steel forgings - Part 3: Ultrasonic testing of ferritic or martensitic steel forgings
ASTM E 446 : 2015 : REDLINE Standard Reference Radiographs for Steel Castings Up to 2 in. (50.8 mm) in Thickness
EN 10028-7:2000 Flat products made of steels for pressure purposes - Part 7: Stainless steels
ASTM E 186 : 2015 : REDLINE Standard Reference Radiographs for Heavy-Walled (2 to 4<fraction><num>1</num><den>2</den></fraction > in. (50.8 to 114 mm)) Steel Castings
EN 10222-2:1999 Steel forgings for pressure purposes - Part 2: Ferritic and martensitic steels with specified elevated temperature properties
EN 10213:2007+A1:2016 Steel castings for pressure purposes
ASTM E 446 : 2014 Standard Reference Radiographs for Steel Castings Up to 2 in. (50.8 mm) in Thickness
EN 10028-3:2017 Flat products made of steels for pressure purposes - Part 3: Weldable fine grain steels, normalized
EN 19:2002 Industrial valves - Marking of metallic valves
ASTM E 280 : 2010 Standard Reference Radiographs for Heavy-Walled (4<span class='unicode'>½</span> to 12-in. (114 to 305-mm)) Steel Castings
EN 1759-1:2004 Flanges and their joint - Circular flanges for pipes, valves, fittings and accessories, Class designated - Part 1: Steel flanges, NPS 1/2 to 24
EN 12680-1:2003 Founding - Ultrasonic examination - Part 1: Steel castings for general purposes
EN 10222-3:1998 Steel forgings for pressure purposes - Part 3: Nickel steels with specified low temperature properties
EN 12516-4:2014 Industrial valves - Shell design strength - Part 4: Calculation method for valve shells manufactured in metallic materials other than steel
EN 10025-1:2004 Hot rolled products of structural steels - Part 1: General technical delivery conditions
EN 736-2:2016 Valves - Terminology - Part 2: Definition of components of valves
ISO 5579:2013 Non-destructive testing — Radiographic testing of metallic materials using film and X- or gamma rays — Basic rules
EN 10028-2:2017 Flat products made of steels for pressure purposes - Part 2: Non-alloy and alloy steels with specified elevated temperature properties
EN 10228-1:1999 Non-destructive testing of steel forgings - Part 1: Magnetic particle inspection
EN 10028-7:2016 Flat products made of steels for pressure purposes - Part 7: Stainless steels
EN ISO 9934-1:2016 Non-destructive testing - Magnetic particle testing - Part 1: General principles (ISO 9934-1:2016)
ISO 9692-1:2013 Welding and allied processes — Types of joint preparation — Part 1: Manual metal arc welding, gas-shielded metal arc welding, gas welding, TIG welding and beam welding of steels
ISO 15614-1:2017 Specification and qualification of welding procedures for metallic materials — Welding procedure test — Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys
EN 10028-3:2003 Flat products made of steels for pressure purposes - Part 3: Weldable fine grain steels, normalized
EN 10028-2:2003 Flat products made of steels for pressure purposes - Part 2: Non-alloy and alloy steels with specified elevated temperature properties
EN ISO 5579:2013 Non-destructive testing - Radiographic testing of metallic materials using film and X- or gamma rays - Basic rules (ISO 5579:2013)
EN 10222-3:2017 Steel forgings for pressure purposes - Part 3: Nickel steels with specified low temperature properties
EN 10222-5:2017 Steel forgings for pressure purposes - Part 5: Martensitic, austenitic and austenitic-ferritic stainless steels
EN 10228-3:2016 Non-destructive testing of steel forgings - Part 3: Ultrasonic testing of ferritic or martensitic steel forgings
EN 736-2:1997 Valves - Terminology - Part 2: Definition of components of valves
EN 10028-4:2003 Flat products made of steels for pressure purposes - Part 4: Nickel alloy steels with specified low temperature properties
EN 12516-3:2002/AC:2003 VALVES - SHELL DESIGN STRENGTH - PART 3: EXPERIMENTAL METHOD
ISO 4200:1991 Plain end steel tubes, welded and seamless — General tables of dimensions and masses per unit length
EN 10222-4:2017 Steel forgings for pressure purposes - Part 4: Weldable fine grain steels with high proof strength
ISO 9934-1:2016 Non-destructive testing — Magnetic particle testing — Part 1: General principles
EN 10222-2:2017 Steel forgings for pressure purposes - Part 2: Ferritic and martensitic steels with specified elevated temperatures properties
EN 1369:2012 Founding - Magnetic particle testing
EN 462-1:1994 Non-destructive testing - Image quality of radiographs - Part 1: Image quality indicators (wire type) - Determination of image quality value
ASTM E 280 : 2015 : REDLINE Standard Reference Radiographs for Heavy-Walled (4<fraction><num>1</num><den>2</den></fraction > to 12 in. (114 to 305 mm)) Steel Castings
EN 12681 : 2003 FOUNDING - RADIOGRAPHIC EXAMINATION
ASTM E 186 : 2010 Standard Reference Radiographs for Heavy-Walled (2 to 4<span class='unicode'>½</span>-in. (50.8 to 114-mm)) Steel Castings
ISO 7005-1:2011 Pipe flanges — Part 1: Steel flanges for industrial and general service piping systems
EN 12516-2:2014 Industrial valves - Shell design strength - Part 2: Calculation method for steel valve shells
EN 10222-5:1999 Steel forgings for pressure purposes - Part 5: Martensitic, austenitic and austenitic-ferritic stainless steels
EN 571-1:1997 Non destructive testing - Penetrant testing - Part 1: General principles
EN 10028-4:2017 Flat products made of steels for pressure purposes - Part 4: Nickel alloy steels with specified low temperature properties
EN 19:2016 Industrial valves - Marking of metallic valves
EN 10222-4:1998 Steel forgings for pressure purposes - Part 4: Weldable fine grain steels with high proof strength
EN 736-3:2008 Valves - Terminology - Part 3: Definition of terms
EN ISO 9934-1:2001 Non-destructive testing - Magnetic particle testing - Part 1: General principles (ISO 9934-1:2001)
EN 287-1:2011 Qualification test of welders - Fusion welding - Part 1: Steels

View more information
$391.19
Including GST where applicable
AUD
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - English
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Learn more on subscription solutions

or

Get in touch with us

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more