Skip to content
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Go to AMERICAS site X
Please enter a keyword to search
  • Preview

    I.S. EN 13236:2010

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    View superseded by
    This Standard has been added successfully to your Watchlist
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    SAFETY REQUIREMENTS FOR SUPERABRASIVE PRODUCTS

    Available format(s):  Hardcopy, PDF

    Superseded date:  14-05-2019

    Language(s):  English

    Published date:  01-01-2010

    Publisher:  National Standards Authority of Ireland

    Add to Watchlist

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    National Foreword
    European foreword
    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms, definitions and symbols
    4 List of significant hazards
    5 Safety requirements
    6 Verification of the safety requirements
    7 Information for use
    Annex A (normative) - Marking
    Annex B (normative) - Colour codes
    Annex C (informative) - Mounted points
    Annex D (normative) - Reconditioning of cutting-off wheels
            according to 5.3.6.4
    Annex E (informative) - Speed conversion table
    Bibliography

    Abstract - (Show below) - (Hide below)

    Pertains only to superabrasives products containing natural or synthetic diamond or cBN (cubic boron Nitride).

    General Product Information - (Show below) - (Hide below)

    Development Note 2010 Edition Re-Issued in January 2016 & incorporates AMD 1 2015. (02/2016)
    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Superseded
    Superseded By
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    EN 60745-2-3:2011/A13:2015 HAND-HELD MOTOR-OPERATED ELECTRIC TOOLS - SAFETY - PART 2-3: PARTICULAR REQUIREMENTS FOR GRINDERS, POLISHERS AND DISK-TYPE SANDERS
    ISO 6106:2013 Abrasive products Checking the grain size of superabrasives
    EN ISO 286-1:2010/AC:2013 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - ISO CODE SYSTEM FOR TOLERANCES ON LINEAR SIZES - PART 1: BASIS OF TOLERANCES, DEVIATIONS AND FITS (ISO 286-1:2010/COR 1:2013)
    ISO 19432:2012 Building construction machinery and equipment Portable, hand-held, internal combustion engine driven cut-off machines Safety requirements
    EN 12413:2007+A1:2011 Safety requirements for bonded abrasive products
    ISO 3864-2:2016 Graphical symbols — Safety colours and safety signs — Part 2: Design principles for product safety labels
    EN 13218:2002+A1:2008/AC:2010 MACHINE TOOLS - SAFETY - STATIONARY GRINDING MACHINES
    ISO 6104:2005 Superabrasive products Rotating grinding tools with diamond or cubic boron nitride General survey, designation and multilingual nomenclature
    EN 792-9:2001+A1:2008 Hand-held non-electric power tools - Safety requirements - Part 9: Die grinders
    1995/16/EC : 1995 DIRECTIVE 95/16/EC OF 29 JUNE 1995 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES RELATING TO LIFTS
    IEC 60745-2-3:2006+AMD1:2010+AMD2:2012 CSV Hand-held motor-operated electric tools - Safety - Part 2-3: Particular requirements for grinders, polishers and disk-type sanders
    ISO 666:2012 Machine tools — Mounting of grinding wheels by means of hub flanges
    ISO 286-1:2010 Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 1: Basis of tolerances, deviations and fits
    EN 22768-1:1993 General tolerances - Part 1: Tolerances for linear and angular dimensions without individual tolerance indications (ISO 2768-1:1989)
    EN ISO 19432:2012 Building construction machinery and equipment - Portable, hand-held, internal combustion engine driven cut-off machines - Safety requirements (ISO 19432:2012)
    ISO 286-2:2010 Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts
    EN 792-7:2001+A1:2008 Hand-held non-electric power tools - Safety requirements - Part 7: Grinders
    ISO 22917:2016 Precision superabrasives Limit deviations and run-out tolerances for grinding wheels with diamond or cubic boron nitride
    1998/37/EC : 1998 DIRECTIVE 98/37/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 22 JUNE 1998 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES RELATING TO MACHINERY
    EN ISO 286-2:2010/AC:2013 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - ISO CODE SYSTEM FOR TOLERANCES ON LINEAR SIZES - PART 2: TABLES OF STANDARD TOLERANCE CLASSES AND LIMIT DEVIATIONS FOR HOLES AND SHAFTS (ISO 286-2:2010/COR 1:2013)
    EN 13743:2017 Safety requirements for coated abrasive products
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective
Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more